Horizon Hobby DSTX1 User Guide

®

ST. RATE

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc.

For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate various levels of potential harm when operating
this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no
possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility
of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and
serious injury OR create a high probability of superficial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some

basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to
the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt
disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc.
This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions
and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

EN

WARNING AGAINST COUNTERFEIT PRODUCTS: Thank you for purchasing a genuine Spektrum product. Always

purchase from a Horizon Hobby, Inc. authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, Inc.
disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or
products claiming compatibility with DSM or Spektrum.

Age Recommendation:
Not for Children under 14 years. This is not a toy.

NOTICE: This product is only intended for use with

unmanned, hobby-grade, remote-controlled vehicles and
aircraft. Horizon Hobby disclaims all liability outside of the
intended purpose and will not provide warranty service
related thereto.

INSTALLING THE
TRANSMITTER BATTERIES

FRANCE RF SETTING:

The DX2E has a France RF setting that complies with French
regulations. When in France, always use the France power
setting when operating the transmitter outdoors.

WARRANTY REGISTRATION

Visit www.spektrumrc.com/registration today
to register your product.

BATTERY LED MONITOR

POWER

Solid Green Battery is good (Above 4V)
Flashing Green Battery voltage is critically low. Replace batteries

(below 4V)

ST. TRIM

SPEKTRUM DX2E USER GUIDE

1

EN

RECEIVER COMPATIBILITY

The DX2E is compatible with all Spektrum™ DSM®, DSM2™
and Marine surface receivers.

RECEIVER CONNECTION
AND INSTALLATION

Antenna
LED

SR200

THR
STR
BIND

Throttle Port
Steering Port
Bind/Battery Port
Bind Plug

1. With the receiver off, insert the bind plug into the BIND
port on the receiver.

2. Power the receiver through any other port. The green
LED will flash continuously, indicating the receiver is
in bind mode.

3. With the steering wheel and throttle trigger in the desired
preset failsafe positions (see the Failsafe section on this
page for more information), press and hold the bind
button and turn on the transmitter. The green LED on the
front of the transmitter will flash within three seconds,
indicating the transmitter is in bind mode. Release the
bind button when the green LED flashes. Continue to
hold the failsafe positions until the binding process
is complete.

Bind Button

Typical Electric Installation

2.4Ghz DSM

SR200

SPORT SURFACE

RECEIVER

Receiver

Battery

Electronic

Speed Control

THR

STR

BIND

Steering Servo

To Motor

Typical Gas Installation

Receiver

2.4Ghz DSM

SR200

THR

SPORT SURFACE

RECEIVER

STR

BIND

Install the Receiver in your vehicle using double-sided foam
servo tape. Foam servo tape will hold the receiver in place
and help isolate it from vibrations. Mount the antenna up
and away from the vehicle in an antenna tube. The higher
up the antenna is, the better signal it will receive.

NOTICE: Do not cut the antenna.

Throttle Servo

Steering Servo

Battery

BINDING A RECEIVER

Binding is the process of programming the receiver to
recognize the GUID (Globally Unique Identifier) code of a
single specific transmitter. When a receiver is bound to
a transmitter, the receiver will only respond to that specific
transmitter. The DX2E and SR200 are bound at the factory,
but if you need to rebind for any reason, please follow
these steps:

BIND THST

N R N R

4. The LED on the receiver will glow solid when the
transmitter and receiver are bound.

5. Remove the bind plug and store it in a convenient place.

You must rebind when:

• Differentfailsafepositionsaredesirede.g.,whenthrottle
or steering reversing has been changed.

• Changingreceivertypese.g.,changingfromaDSM
receiver to a DSM2 or Marine receiver.

• Bindingthereceivertoadifferenttransmitter.

Some Spektrum receivers, like the SR3001, use a bind
button rather than a bind plug. The binding process is the
same with this receiver; however, instead of inserting the
plug before powering up the receiver, press and hold the
bind button while powering up the receiver to enter bind
mode.

FAILSAFE

Failsafe positions are also set during binding. In the unlikely
event that the radio link is lost during use, the receiver will
drive the servos to their preprogrammed failsafe positions
(normally full brakes and straight steering). If the receiver
is turned on prior to turning on the transmitter, the receiver
will enter failsafe mode. When the transmitter is turned on,
normal control is resumed. For more information on setting
the failsafe, refer to the Binding a Receiver section above.

SERVO REVERSING

If a right steering command does not result in the wheels
turning right (and vice versa), the channel may need to be
reversed. To reverse a channel, switch the position of the
correlating switch—“N” is for normal, “R” is for reverse. You
can use a small screwdriver to move the switch if necessary.

2 SPEKTRUM DX2E USER GUIDE

Reverse Switch

ST. RATE

ST. RATE

Steering

Reverse Switch
Throttle

EN

Steering Rate Dial

BIND THST

N R N R

STEERING TRIM

The steering trim dial is used to adjust the steering trim
when the wheel is centered. Rotating the dial changes the
steering trim (the steering at rest position). Normally, the
steering trim is adjusted until the vehicle tracks straight.

Steering Trim Dial

ST. TRIM

POWER

TH. TRIM

THROTTLE TRIM

The throttle trim dial is used to adjust the throttle trim
when the throttle stick is released (neutral position). This is
typically used to adjust the brakes. Rotating the dial causes
the throttle trim (the throttle position at rest) to be changed.

Throttle Trim Dial

ST. TRIM

POWER

TH. TRIM

STEERING RATE

Steering rate (also known as dual rate) allows on-the-fly
steering travel adjustments to be made using the steering
rate dial. Steering rate limits the amount of travel of the
steering servo. The steering rate cannot be greater
than 100%.

ST. RATE

RF MODE

The DX2E has a France RF Mode that complies with French
regulations. The DX2E must be in France mode when used
outdoors in France. At all other times, the transmitter should
be in Standard mode.

FRANCE MODE

Turn the wheel full left, pull the trigger full throttle and
hold down the bind button while turning on the transmitter.
The Green LED will flash twice.

STANDARD MODE

Turn the wheel full right, pull the trigger full throttle and
hold down the bind button while turning on the transmitter.
The Green LED will flash once.

GENERAL NOTES

Radio controlled models are a great source of pleasure.
Unfortunately, they can also pose a potential hazard if not
operated and maintained properly. It is imperative to install
your radio control system correctly. Additionally, your level of
operating competency must be high enough to ensure you
are able to control your model under all conditions. If you are
a newcomer to radio controlled models, please seek help
from an experienced modeler or your local hobby shop.

SAFETY POINTS TO OBEY FOR MODELERS

• Ensureyourbatteries(bothtransmitterandreceiver)
have been properly charged for your model.

• Checkallservosandtheirconnectionspriortoeachrun.

• Donotoperateyourmodelnearspectators,parkingareas

or any other area that could result in injury to people or
damage of property.

• Donotoperateyourmodelduringadverseweather

conditions. Poor visibility can cause disorientation
and loss of control of your model.

• Donotpointthetransmitterantennadirectlytowardthe

model. The radiation pattern from the tip of the antenna
is inherently low.

• Donottakechances.Ifatanytimeduringtheoperation
of your model you observe any erratic or abnormal
operation, immediately stop operation of your model
until the cause of the problem has been ascertained
and corrected. Safety can never be taken lightly.

SPEKTRUM DX2E USER GUIDE

3

EN

2.4GHz TROUBLESHOOTING GUIDE

Problem Possible Cause Solution

The system will not
connect

The receiver goes into
failsafe mode a short
distance away from the
transmitter

The receiver quits
responding during
operation

Your transmitter and receiver are too close
together

You are around metal objects Move to an area with less metal

The model selected is not the model bound to Check model selected and ensure you are bound to

Your transmitter was accidentally put into bind
mode and is no longer bound to your receiver

Check the receiver antenna to be sure it is not
cut or damaged

Inadequate battery voltage Charge batteries. Spektrum receivers require at least

Loose or damaged wires or connectors between
battery and receiver

Move transmitter 8 to 12 feet from receiver

that model

Rebind your transmitter and receiver

Replace the receiver or contact Horizon Product
Support

Make sure your receiver antenna is in an antenna
tube and is above the vehicle

3.5V to operate. An inadequate power supply can
allow voltage to momentarily drop below 3.5V and
cause the receiver to brown out and reconnect

Check the wires and connection between the ba­ttery and receiver. Repair or replace wires and/or
connectors

FCC INFORMATION

This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly

approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless
technology which has been tested and found to be compliant
with the applicable regulations governing a radio transmitter
in the 2.400GHz to 2.4835GHz frequency range.

ANTENNA SEPARATION DISTANCE

When operating your Spektrum transmitter, please be sure
to maintain a separation distance of at least 5 cm between
your body (excluding fingers, hands, wrists, ankles and feet)
and the antenna to meet RF exposure safety requirements
as determined by FCC regulations.

The following illustrations show the approximate 5 cm RF
exposure area and typical hand placement when operating
your Spektrum transmitter.

1-YEAR LIMITED WARRANTY

WHAT THIS WARRANTY COVERS

Horizon Hobby, Inc. (“Horizon”) warrants to the original
purchaser that the product purchased (the “Product”) will be
free from defects in materials and workmanship for a period of
1 year from the date of purchase by the Purchaser.

WHAT IS NOT COVERED

This warranty is not transferable and does not cover (i)
cosmetic damage, (ii) damage due to acts of God, accident,
misuse, abuse, negligence, commercial use, or due to
improper use, installation, operation or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted
service by anyone other than a Horizon Hobby authorized
service center, or (v) Products not purchased from an
authorized Horizon dealer.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE
DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

PURCHASER’S REMEDY

Horizon’s sole obligation and purchaser’s sole and exclusive
remedy shall be that Horizon will, at its option, either (i)
service, or (ii) replace, any Product determined by Horizon
to be defective. Horizon reserves the right to inspect any
and all Product(s) involved in a warranty claim. Service or
replacement decisions are at the sole discretion of Horizon.
Proof of purchase is required for all warranty claims. SERVICE
OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

4 SPEKTRUM DX2E USER GUIDE

LIMITATION OF LIABILITY

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED
IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF
HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. Further, in no event shall the liability of Horizon
exceed the individual price of the Product on which liability
is asserted. As Horizon has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed
nor accepted for any resulting damage or injury. By the act of
use, setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the
liability associated with the use of the Product, purchaser is
advised to return the Product immediately in new and unused
condition to the place of purchase.

LAW

These terms are governed by Illinois law (without regard to
conflict of law principals). This warranty gives you specific
legal rights, and you may also have other rights which vary
from state to state. Horizon reserves the right to change or
modify this warranty at any time without notice.

WARRANTY SERVICES

QUESTIONS, ASSISTANCE, AND SERVICES

Your local hobby store and/or place of purchase cannot
provide warranty support or service. Once assembly, setup or
use of the Product has been started, you must contact your
local distributor or Horizon directly. This will enable Horizon to
better answer your questions and service you in the event that
you may need any assistance. For questions or assistance,
please direct your email to productsupport@horizonhobby.
com, or call 877.504.0233 toll free to speak to a Product
Support representative. You may also find information on our
website at www.horizonhobby.com.

INSPECTION OR SERVICES

If this Product needs to be inspected or serviced, please use
the Horizon Online Service Request submission process found
on our website or call Horizon to obtain a Return Merchandise
Authorization (RMA) number. Pack the Product securely
using a shipping carton. Please note that original boxes may

be included, but are not designed to withstand the rigors
of shipping without additional protection. Ship via a carrier
that provides tracking and insurance for lost or damaged
parcels, as Horizon is not responsible for merchandise until
it arrives and is accepted at our facility. An Online Service
Request is available at http://www.horizonhobby.com under
the Support tab. If you do not have internet access, please
contact Horizon Product Support to obtain a RMA number
along with instructions for submitting your product for service.
When calling Horizon, you will be asked to provide your
complete name, street address, email address and phone
number where you can be reached during business hours.
When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary
of the problem. A copy of your original sales receipt must
be included for warranty consideration. Be sure your name,
address, and RMA number are clearly written on the outside
of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you
have any issue with a Li-Po battery, please contact
the appropriate Horizon Product Support office.

WARRANTY REQUIREMENTS

For Warranty consideration, you must include your
original sales receipt verifying the proof-of-purchase
date. Provided warranty conditions have been met, your

Product will be serviced or replaced free of charge. Service or
replacement decisions are at the sole discretion of Horizon.

NON-WARRANTY SERVICE

Should your service not be covered by warranty service
will be completed and payment will be required without
notification or estimate of the expense unless the
expense exceeds 50% of the retail purchase cost. By

submitting the item for service you are agreeing to payment of
the service without notification. Service estimates are available
upon request. You must include this request with your item
submitted for service. Non-warranty service estimates will
be billed a minimum of ½ hour of labor. In addition you will
be billed for return freight. Horizon accepts money orders
and cashiers checks, as well as Visa, MasterCard, American
Express, and Discover cards. By submitting any item to
Horizon for service, you are agreeing to Horizon’s
Terms and Conditions found on our website
http://www.horizonhobby.com/Service/Request/.

WARRANTY AND SERVICE CONTACT INFORMATION

Country of Purchase Horizon Hobby Address Phone Number/Email Address

United States
of America

United Kingdom Horizon Hobby Limited Units 1-4 Ployters Rd

Germany Horizon Technischer Service Christian-Junge-Straße 1

France Horizon Hobby SAS 14 Rue Gustave Eiffel

China Horizon Hobby China Room 506, No. 97 Changshou Rd.

Horizon Service Center
(Electronics and engines)

Horizon Product Support
(All other products)

4105 Fieldstone Rd
Champaign, Illinois, 61822 USA

4105 Fieldstone Rd
Champaign, Illinois, 61822 USA

Staple Tye, Harlow, Essex
CM18 7NS, United Kingdom

25337 Elmshorn, Germany

Zone d’Activité du Réveil Matin
91230 Montgeron

Shanghai, China 200060

877-504-0233
Online Repair Request:
visit www.horizonhobby.com/service

877-504-0233
[e-mail]

[phone]
[e-mail]

[phone]
[e-mail]

[phone]
[e-mail]

[phone]
[e-mail]

EN

SPEKTRUM DX2E USER GUIDE

5

EN

PARTS CONTACT INFORMATION

Country of Purchase Horizon Hobby Address Phone Number/Email Address

United States Sales

United Kingdom Horizon Hobby Limited

Germany Horizon Hobby GmbH

France Horizon Hobby SAS

China Horizon Hobby China

4105 Fieldstone Rd
Champaign, Illinois, 61822 USA

Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS, United Kingdom

Christian-Junge-Straße 1
25337 Elmshorn, Germany

14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron

Room 506, No. 97 Changshou Rd.
Shanghai, China 200060

800-338-4639
[e-mail]

[phone]
[e-mail]

[phone]
[e-mail]

[phone]
[e-mail]

[phone]
[e-mail]

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

Instructions for disposal of WEEE
by users in the European Union

This product must not be disposed of with other waste.
Instead, it is the user’s responsibility to dispose of their waste
equipment by handing it over to a designated collections
point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your

Declaration of Conformity

(in accordance with ISO/IEC 17050-1)

No. HH2012010601
Product(s): Spektrum DX2E/

Item Number(s): SPMR2300, SPM2300
Equipment class: 2
The object of declaration described above is in conformity
with the requirements of the specifications listed below,
following the provisions of the European R&TTE directive
1999/5/EC:

EN 300-328 V1.7.1
EN 301 489-1 V1.7.1: 2006
EN 301 489-17 V1.3.2: 2008
EN 60950-1:2006+A11

Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
January 6, 2011

Spektrum DX2E with SR200

International Operations and Risk Management

Horizon Hobby, Inc.

waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner
that protects human health and the environment. For more
information about where you can drop off your waste equip­ment for recycling, please contact your local city office, your
household waste disposal service or where you purchased
the product.

Steven A. Hall

Vice President

6 SPEKTRUM DX2E USER GUIDE

DE

ST. RATE

HINWEIS:

Alle Anweisungen, Garantien und dazugehörigen Dokumente können ohne Ankündigung von Horizon Hobby Inc. geändert

werden. Eine aktuelle Version ersehen Sie bitte im Support Feld unter: http://www.horizonhobby.com

Erklärung der Begriffe

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahrenrisiken
beim Betrieb dieses Produkts hinzuweisen:
HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe
oder keine Gefahr von Verletzungen ergeben.
ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die
Gefahr von schweren Verletzungen.
WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,
Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberflächliche Verletzungen.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen vertraut

zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem Eigentum führen
oder schwere Verletzungen verursachen.

Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug. Dies ist ein hochentwickeltes Hobby-Produkt. Es muss
mit Vorsicht und gesundem Menschenverstand betrieben werden und benötigt gewisse mechanische Grundfähigkeiten. Wird
dieses Produkt nicht auf eine sichere und verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden
am Produkt oder anderen Sachwerten führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne
direkte Überwachung eines Erwachsenen. Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby, Inc., das Produkt zu
zerlegen, es mit inkompatiblen Komponenten zu verwenden oder auf jegliche Weise zu erweitern. Diese Bedienungsanleitung
enthält Anweisungen für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder
Verwendung alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß
betrieben werden kann und Schäden oder schwere Verletzungen vermieden werden.

WARNUNG ZU GEFÄLSCHTEN PRODUKTEN: Vielen

Dank, dass Sie sich dieses Spektrum Produkt gekauft haben.

EINSETZEN DER SENDERBATTERIEN

Bitte kaufen Sie Ihre Spektrum Produkte immer von einem
autorisiertem Händler um sicherzu stellen, dass Sie ein
authentisches hochqualitatives original Spektrum Produkt
gekauft haben. Horizon Hobby lehnt jede Unterstützung,
Service oder Garantieleistung von gefälschten Produkten
oder Produkten ab die von sich in Anspruch nehmen
kompatibel mit Spektrum oder DSM zu sein.

Nicht geeignet für Kinder unter 14 Jahren.
Dies ist kein Spielzeug.

HINWEIS: Dieses Produkt ist ausschließlich für die

Verwendung in unbemannten ferngesteuerten Fahrzeugen

BATTERY LED MONITOR

und Fluggeräten im Hobbybereich vorgesehen. Horizon Hobby
lehnt jede Haftung und Garantieleistung ausserhalb der
vorgesehen Verwendung ab.

RF EINSTELLUNG FRANKREICH

POWER

ST. TRIM

Die DX2E hat eine französische RF Einstellung die mit den
Bestimmungen in Frankreich kompatibel ist. Bitte benutzen
Sie wenn Sie in Frankreich den Sender im Freien betreiben
immer diese Einstellung.

GARANTIEREGISTRIERUNG

Grün Batterie ist OK (über 4V)
Grün blinkt Batteriespannung ist kritisch niedrig.
Ersetzen Sie die Batterien. (unter 4 Volt)

Registrieren Sie bitte heute Ihr Produkt unter
www.spektrumrc.com/registration.

®

SPEKTRUM DX2E Bedienungsanleitung

7

DE

EMPFÄNGER KOMPATIBILITÄT

Die DX2E ist kompatibel mit allen Spektrum™ DSM,
DSM2™ und Marine Empfängern.

EMPFÄNGEREINBAU
UND ANSCHLÜSSE

Antenne
LED

SR200

THR
STR
BIND

TYPISCHER ELEKTROEINBAU

Akku

Elektronischer

Empfänger

2.4Ghz DSM

SR200

SPORT SURFACE

RECEIVER

THR

STR

BIND

Fahrtenregler

Lenkservo

TYPISCHER VERBRENNEREINBAU

Empfänger

2.4Ghz DSM

SR200

THR

SPORT SURFACE

RECEIVER

STR

BIND

Befestigen Sie den Empfänger mit doppelseitigen
Schaumklebeband. Das Klebeband hält den Empfänger
in Position und schützt ihn vor Vibrationen. Schieben Sie
die Antenne in ein Antennenröhrchen und stellen dieses
aufrecht. Je höher die Antenne steht, desto besser wird
sie das Signal empfangen.

HINWEIS: Schneiden oder kürzen Sie die Antenne nicht.

Anschluß Gas
Anschluß Lenkung
Bindestecker/

Akkuanschluß
Bindestecker

Zum Motor

Gasservo

Lenkservo

Akku

1. Stecken Sie mit ausgeschalteten Empfänger den
Bindestecker in den Bindeanschluß des Empfängers.

2. Schalten Sie den Empfänger durch einen beliebigen
anderen Anschluß ein. Die grüne LED blinkt und zeigt
damit den Binde Mode an.

3. Mit dem Gashebel und Lenkrad in den gewünschten
Preset Failsafepositionen (siehe dazu den Abschnitt
Failsafe auf dieser Seite) drücken und halten Sie den
Bindeknopf gedrückt und schalten den Sender ein.
Die grüne LED auf der Vorderseite des Senders blinkt
innerhalb von drei Sekunden und zeigt damit an, dass
sich der Sender im Bindemode befindet. Lassen Sie
den Knopf los wenn die grüne LED blinkt. Halten Sie die
Failsafepositionen bis der Bindevorgang durchgeführt ist.

Bindeknopf

BIND THST

N R N R

4. Die LED auf dem Empfänger leuchtet und zeigt damit an,
dass Sender und Empfänger gebunden sind.

5. Nehmen Sie den Bindestecker aus dem Bindeport
herraus und heben ihn sorgfältig auf.

Sie müssen den Bindevorgang wiederholen wenn:

• SieandereFailsafepositionenwünschen,oderwenn
die Gas- oder Lenkfunktion reversiert wurden.

• SieeinenanderenEmpfängerverwendenodervoneinem

DSM zu einem DSM2 oder Marine Empfänger wechseln.

• SiedenEmpfängeraneinenanderenSenderbinden.

Einige Spektrum Empfänger wie zum Beispiel der SR3001
haben einen Bindeknopf und keinen Bindeanschluß.
(Port) Der Bindevorgang ist der gleiche. Statt vorher
den Bindestecker einzustecken, drücken und halten Sie
den Bindeknopf gedrückt während Sie den Empfänger
einschalten um in den Bindemode zu gelangen.

FAILSAFE

Die Failsafepositionen werden während des Bindes
eingestellt. In dem unvorhergesehenden Fall, dass die RF
Verbindung unterbrochen wird, fährt der Empfänger die
Servos in die vorprogrammierten Failsafepositionen. Sollte
der Empfänger vor dem Sender eingeschaltet werden geht
der Empfänger in den Failsafemode. Wird dann der Sender
eingeschaltet haben, Sie wieder normale Kontrolle über
das Modell. Für mehr Informationen über das Einstellen der
Faisafepositionen sehen Sie bitte im Abschnitt-Binden des
Empfänger nach.

BINDEN DES EMPFÄNGERS

Binden ist der Prozess der Programmierung des Empfänger
mit dem eindeutigen Signal eines spezifischen Senders
(GUID). Ist der Empfänger an den Sender gebunden, wird nur
er auf die Signale des Senders reagieren. Die DX2E und der
SR200 sind ab Werk gebunden. Sollten Sie diese neu binden
wollen folgen Sie bitte dieses Schritten:

8 SPEKTRUM DX2E Bedienungsanleitung

SERVOREVERSE

Sollte die Lenkbewegung nach Rechts nicht zur Folge haben,
dass sich die Reifen auch nach rechts bewegen, müssen
Sie den Kanal reversieren (umdrehen). Um den Kanal zu
reversieren schalten Sie den dazugehörigen Schalter auf
die andere Position - N steht für Normal, R für Reversiert.
Sie können einen kleinen Schraubendreher nutzen um die
Schalter zu bewegen.