Horizon Hobby DASRX12 Users manual

SRS4210 | AR636H

SRS4200 | SRS4201

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁcial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become

familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS

Always purchase from a Horizon Hobby, Inc. authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, Inc. disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and aircraft. Horizon Hobby disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.

Warranty Registration

Visit www.spektrumrc.com/registration today to register your product.

WATERPROOF COMPONENT

Your new Spektrum™ receiver has been designed and built to allow you to operate your vehicle in many wet conditions, including puddles, creeks, wet grass, snow and even rain.

While waterproof, this component has not been designed to be immersed in water for long periods of time and should NOT be treated like a submarine. In addition, most metal parts, including any screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions.

To maximize the long-term performance of your receiver and to keep the warranty intact, it should only be used as described in the “Usage Conditions” section of this manual. Additionally, the procedures described in the “Wet Conditions Maintenance” section must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate your vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and

comply with the following precautions could result in product malfunction and/or void the warranty.

General Precautions

Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your receiver.

Do not operate your receiver where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.

Usage Conditions

Your receiver will operate successfully in any of the following, individual-usage scenarios:

•

2 hours continuous operation in dew-covered (damp) grass or vegetation.

•

2 hours continuous operation in heavy fog (95% humidity, saturated air, condensing water).

•

1 hour continuous operation in light rain (< 0.10 in / 2.5mm per hour).

•

15 minutes continuous operation in heavy rain (> 0.30 in / 7.6mm per hour).

•

1 hour continuous operation in light sleet (< 0.10 in / 2.5mm per hour).

•

1 hour continuous operation in light snow (< 0.25 in / 6.35mm per hour).

•

45 minutes continuous operation in standing or running fresh water (the water level should always remain below the vehicle frame), or constant splashing water, without any immersion of waterproof component(s).

•

5 minutes continuous operation in standing or running fresh water (the water level should never rise higher than 0.5 in (about 10 mm) above the vehicle frame), constant splashing water, or frequent, intermittent immersion of waterproof component(s).

•

1 hour continuous operation in damp sand, dirt, mud or snow (the material level should always be below the vehicle frame), constant splatter without any immersion or coverage of waterproof component(s).

Furthermore, when appropriate maintenance procedures (as described below) are performed promptly following exposure, the receiver will remain best protected from corrosion or other long-term, water-related damage.

Wet Conditions Maintenance

•

Gently rinse the mud and dirt off the vehicle with a garden hose.

•

Remove the battery pack(s) and dry the contacts.

•

If you have an air compressor or a can of compressed air available, blow off the receiver to help remove any water that may have gotten into small crevices or corners. Dry any water that may be inside a recessed connector housing.

•

Let the receiver air dry before you store it. Water may continue to seep or evaporate out of tight areas for a few hours.

NOTICE: Never use a pressure washer to clean your vehicle. NOTICE: The receiver is waterproofed for use in wet conditions. Make sure

the other components in your vehicle are waterproof or water-resistant before driving in wet conditions.

AVC – ACTIVE VEHICLE CONTROL

AVC™ technology is the newest Spektrum™ RC innovation from Horizon Hobby. This Spektrum stabilization system adds a whole new level of control to your RC driving experience. AVC technology utilizes sensors to adjust steering and throttle output, providing you with a more stable and controlled driving experience.

NOTICE: You must use digital servos with the SR4210 receiver. Using analog servos will reduce the performance of the system and may cause analog servos to overheat.

SRS4210 INSTRUCTION MANUAL

The Spektrum™ SRS4210 DSMR™ Surface receiver is compatible with all Spektrum DSMR transmitters and is also backwards compatible with DSM2® transmitters. The SRS4210 receiver is NOT compatible with DSM® transmitters. For a complete list of compatible transmitters, see the SRS4210 product page on spektrumrc.com.

Speciﬁcations

Type: DSMR Dimensions (LxWxH):

1.43 x 0.96 x 0.51 in (36.3 x 24.4 x 13.0mm)

Channels: 2, 4 with AVC disabled

Bind/Battery Port

Disable Port

Data Port Aux 2 Port Aux 1 Port

Throttle Port

Steering Port

Aux channels

The Aux channels can operate as additional servo channels, or as a power supply for a personal transponder. If AVC is active, only two channels, Steering and Throttle, are operational. The Aux channels can be used to power a personal transponder or lights.

If AVC is disabled (see DISABLING THE STABILITY ASSIST FUNCTION to disable AVC), the Aux channels will operate as servo channels.

Weight: 10.9 g (0.39 oz) Band: 2.4GHz Voltage Range:

3.5–9.6V

Antenna

Receiver Connection and Installation

You must install the receiver in the vehicle before binding the transmitter and receiver. The receiver can be mounted ﬂat with the label up or on its side. When you bind the receiver, the AVC system automatically detects the orientation of the receiver. The receiver must be mounted completely ﬂat when in the label-up orientation or completely perpendicular when mounted on its side. If the receiver is angled even slightly, AVC may not function properly. If the orientation of the receiver is changed after binding, you must then rebind for AVC to fuction properly.

Install the Receiver in your vehicle using the included double-sided foam servo tape. Foam servo tape will hold the receiver in place and help isolate it from vibrations.

IMPORTANT: Do not use hook & loop material to install the SRS4210 receiver. Using hook & loop material will affect the performance of the AVC system.

Mount the antenna up and away from the vehicle in an antenna tube. The higher up the antenna is, the better signal it will receive.

NOTICE: Do not cut or modify the antenna.

Failsafe

In the unlikely event that the radio link is lost during use, the receiver will drive the throttle channel to the neutral position. If the receiver is powered on prior to turning on the transmitter, the receiver will enter the failsafe mode, driving the throttle channel to the neutral position. When the transmitter is turned on, normal control is resumed.

IMPORTANT: Failsafe activates only in the event that signal is lost from the transmitter. Failsafe will NOT activate in the event that receiver battery power decreases below the recommended minimums or power to the receiver is lost.

Powering the receiver with a separate receiver pack

Battery

Throttle Servo

Steering Servo

Receiver

Powering the receiver with an ESC

Battery

To Motor

Steering

Servo

IMPORTANT: If you adjust the steering and throttle trim on your transmitter, the receiver must be turned off and back on again in order to save the new trim settings. Otherwise, AVC will not function properly.

Electronic Speed Control

Receiver

Binding Receiver to Transmitter

In order to operate, the receiver must be bound to the transmitter. Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identiﬁer) code of a single speciﬁc transmitter. When areceiver is bound to atransmitter/model memory, the receiver will only respond to that speciﬁc transmitter/model memory.

Binding and Calibrating the Receiver

You must calibrate the receiver each time it is placed in bind mode. IMPORTANT: The following sequence of steps must be followed in order

for AVC to function properly.

1. Insert the Bind Plug in the BIND port on the receiver.

2. Power on the receiver. The orange LED ﬂashes, indicating the receiver is in bind mode.

3. Center the ST TRIM and TH TRIM on the transmitter.

4. Put your transmitter in bind mode.

5. The bind process is complete when the orange LED on the receiver is solid.

6. Pull the transmitter trigger to Full Throttle.

7. Push the transmitter trigger to Full Brake, then return the trigger to center.

8. Turn the transmitter steering wheel to Full Right.

9. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center. The orange LED ﬂashes once.

10. Remove the bind plug once the calibration and binding process is complete.

11. Power off the transmitter.

IMPORTANT: You must rebind the transmitter and receiver if you:

•

Change the servo reverse after binding

•

Change the travel after binding

•

Want to use the receiver with a different model memory

If you change the servo reversing or travel adjust after binding, AVC will not work properly.

Disabling the Stability Assist Function

If you participate in organized racing, you may be required to turn AVC technology off. To turn off AVC technology, insert a second Bind Plug in the Disable port before binding.

IMPORTANT: You must calibrate the receiver each time it is placed in bind mode. To activate AVC, see the steps in BINDING AND CALIBRATING THE RECEIVER.

2.4GHZ TROUBLESHOOTING GUIDE

Problem Possible Cause Solution

The system will not connect

The receiver goes into failsafe mode a short distance away from the transmitter

The receiver stops responding during operation

The front wheels oscillate

The front wheels turn the wrong way when the car slides/ rotates

The throttle does not reduce when the car slides/rotates

Your transmitter and receiver are too close together

You are around metal objects

The receiver is not bound to the active model memory

Your transmitter was accidentally put into bind mode and is no longer bound to your receiver

Check the receiver antenna to be sure it is not cut or damaged

Inadequate battery voltage

Loose or damaged wires or connectors between battery and receiver

The steering gain is set too high

The steering channel was reversed after calibration

The throttle channel was reversed after calibration

Move transmitter 1 to 3 meters from receiver

Move to an area with less metal

Check model selected and ensure you are bound to that model

Rebind your transmitter and receiver

Replace the receiver or contact Horizon Product Support

Make sure your receiver antenna is in an antenna tube and is above the vehicle

Charge or replace the receiver batteries. Spektrum receivers require at least 3.5V to operate (We recommend using a 6V receiver pack). An inadequate power supply can allow voltage to momentarily drop below 3.5V and cause the receiver to brown out and reconnect

Check the wires and connection between the battery and receiver. Repair or replace wires and/or connectors

Turn down the steering gain

Rebind and calibrate

EN10EN

1-YEAR LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, Inc., (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 1 years from the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modiﬁcation of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂict of law principals).This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http:// www.horizonhobby.com/content/service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support ofﬁce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty

conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and payment will be required without notiﬁcation or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing

to payment of the service without notiﬁcation. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts

EN12EN

money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http:// www.horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notiﬁcation, after which it will be discarded.

Warranty and Service Contact Information

Country

Purchase

United

States of

America

Horizon

Hobby

Horizon Service

Center

(Repairs and Repair

Requests)

Horizon Product

Support

(Product

Technical

Assistance)

Sales

Horizon

Technischer

Service

Sales: Horizon

Hobby GmbH

Contact

Information

servicecenter.horizonhobby.com/

RequestForm/

productsupport@horizonhobby.com

877-504-0233

websales@horizonhobby.com

800-338-4639

service@horizonhobby.eu

+49 (0) 4121 2655 100

Address

4105 Fieldstone Rd Champaign, Illinois,

61822

USA

Hanskampring 9

D 22885 Barsbüttel,

Germany

FCC Statement

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which

the receiver is connected.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: Modiﬁcations to this product will void the user’s authority to operate this equipment.

IC Statement

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”

Antenna Separation Distance

When operating your transmitter, please be sure to maintain a separation distance of at least 20 cm between your body (excluding ﬁngers, hands, wrists, ankles

20 cm

and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.

This illustration shows the approximate 20 cm RF exposure area and typical hand placement when operating your transmitter.

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

EU Compliance Statement: Horizon Hobby, LLC hereby declares

that this product is in compliance with the essential requirements and other relevant provisions of the RED directive.

A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the

user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city ofﬁce, your household waste disposal service or where you purchased the product.

HINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby, Inc. jederzeit geändert werden. Die aktuelle Produktliteratur ﬁnden Sie auf horizonhobby.com unter der Registerkarte „Support“ für das betreffende Produkt.

SPEZIELLE BEDEUTUNGEN

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden, Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂächliche Verletzungen.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die Gefahr von schweren Verletzungen.

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND eine geringe oder keine Gefahr von Verletzungen ergeben.

Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung durch,

um sich vor der Inbetriebnahme mit den Funktionen des Produkts vertraut zu machen. Wird dieses Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder anderen Sachschäden und zu schweren Verletzungen führen.

Dies ist ein hochentwickeltes Hobbyprodukt und KEIN Spielzeug. Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden und erfordert gewisse technische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines Erwachsenen. Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby, Inc., das Produkt zu zerlegen, es mit inkompatiblen Komponenten zu verwenden oder auf jegliche Weise zu erweitern. Diese Bedienungsanleitung enthält Anweisungen für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit das Produkt bestimmungsgemäß betrieben werden kann und Schäden oder schwere Verletzungen vermieden werden.

WARNUNG ZU GEFÄLSCHTEN PRODUKTEN

Bitte kaufen Sie Ihre Spektrum Produkte immer von einem autorisiertem Händler um sicherzu stellen, dass Sie ein authentisches hochqualitatives original Spektrum Produkt gekauft haben. Horizon Hobby lehnt jede Unterstützung, Service oder Garantieleistung von gefälschten Produkten oder Produkten ab die von sich in Anspruch nehmen kompatibel mit Spektrum oder DSM zu sein.

HINWEIS: Dieses Produkt ist ausschließlich für die Verwendung inunbemanten, ferngesteuerten Fahrzeugen und Fluggeräten im Hobbybereich vorgese-hen. Horizon Hobby lehnt jede Haftung und Garantieleistung ausserhalb der vorgesehen Verwendung ab.

Garantie Registrierung

Registrieren Sie bitte Ihr Produkt unter www.spektrumrc.com/registration.

WASSERFESTE KOMPONENTE

Ihr neuer Spektrum Empfänger wurde entwickelt und gebaut um den Betrieb in feuchten Umgebungen inklusive Pfützen, Bächen, nassem Gras, Schnee oder sogar Regen ermöglichen.

Bitte beachten Sie, dass auch wenn die Komponente wasserfest ist, diese NICHT dafür geeignet ist, längere Zeit unter Wasser getaucht zu werden. Zudem sind die elektrischen Kabel sowie auch die meisten Metallteile, inkl. Schrauben und Muttern, korrosionsanfällig, wenn nach dem Betrieb in nasser Umgebung keine zusätzliche Wartung durchgeführt wird.

Für die Maximierung der Langzeitleistung und den Erhalt der Garantie Ihres Empfängers, sollten Sie dieses nur entsprechend der „Nutzungsbedingungen“ einsetzen. Wenn Sie in feuchten Umgebungen fahren, sollten Sie außerdem regelmäßig die Wartung, wie in der Wartungsanleitung unter „Nach Einsatz in nasser Umgebung“ beschrieben, durchführen. Wenn Sie diese zusätzliche Wartung nicht ausführen möchten, dann sollten Sie das Produkt auch nicht unter diesen Bedingungen betreiben.

ACHTUNG: Unaufmerksamkeit beim Betrieb des Produktes

und in Zusammenhang mit den folgenden Sicherheitshinweisen kann zu Fehlfunktionen und dem Verlust der Garantie führen.

Allgemeine Sicherheitshinweise

Bitte lesen Sie sich die Wartungsanleitung für den Einsatz in nasser Umgebung sorgfältig durch und stellen Sie sicher, dass Sie alle Werkzeuge für eine Wartung des Servos zur Verfügung haben.

Betreiben Sie Ihr Servo nicht dort, wo es in Kontakt mit Salzwasser (Meerwasser oder mit Salz bedeckten Straßen) oder mit schmutzigem oder belastetem Wasser kommen kann. Salzwasser ist stark leitend und korrosionsfördernd, seien Sie daher bitte sehr achtsam.

Nutzungsbedingungen

Ihr Empfänger kann erfolgreich unter folgenden Bedingungen in einem der folgenden Szenarios eingesetzt werden:

•

2 Stunden unterbrochener Betrieb in taubedeckten Gras oder Vegetation.

•

2 Stunden Dauerbetrieb in dichtem Nebel (95% Luftfeuchtigkeit, gesättigte Luft, Kondenswasser).

•

1 Stunde Dauerbetrieb in leichtem Regen (<2,5mm per Stunde).

•

15 Minuten Dauerbetrieb in starkem Regen (>7,6mm per Stunde).

•

1 Stunde Dauerbetrieb in leichtem Graupel (<2,5mm per Stunde).

•

1 Stunde Dauerbetrieb bei leichtem Schneefall (<6,35mm per Stunde).

•

45 Minuten Dauerbetrieb in Süßwasser (die Wasserhöhe darf dabei nicht die untere Chassiskante übersteigen oder bei kontinuierlichem Kontakt mit Spritzwasser, jedoch ohne Eintauchen der wasserdichten Komponenten.

•

5 Minuten Dauerbetrieb in Süßwasser (die Wasserhöhe darf die untere Chassiskante um max. 10mm übersteigen), bei kontinuierlichem Kontakt mit Spritzwasser oder bei ständigem kurzen Eintauchen der wasserdichten Komponenten.

•

1 Stunde unterbrochener Betrieb in Sand, Matsch oder Schnee (die untere Rumpfkante sollte nicht durch den Untergrund überdeckt werden), bei Kontakt mit Spritzwasser, jedoch ohne Eintauchen der wasserfesten Komponenten.

Führen Sie im Anschluss unverzüglich die beschriebenen Wartungsmaßnahmen durch und das Servo ist bestens gegen Korrosion und andere langfristige Wasserschäden geschützt.

Wartung nach Fahrten in nasser Umgebung

•

Nehmen Sie die Akkus aus dem Fahrzeug heraus und trocknen die Kontakte.

•

Entfernen Sie mit einem Gartenschlauch vorsichtig Dreck und Schmutz von Ihrem Fahrzeug.

•

Sollten Sie einen Kompressor oder Druckluft zur Hand haben, blasen Sie die Innenräume, Ritzen und Spalten des Fahrzeuges aus. Trocknen Sie alle Anschlüsse und Stecker sorgfältig.

•

Lassen Sie das Fahrzeug an der Luft trocknen bevor Sie ihn einlagern. Wasser kann für einige Stunden aus dem Fahrzeug heraus tropfen.

HINWEIS: Verwenden Sie für die Reinigung Ihres Fahrzeuges NIEMALS einen Hochdruckreiniger.

HINWEIS: Der Empfänger ist wasserfest für den Einsatz in nasser Umgebung. Stellen Sie sicher, dass andere Komponenten in Ihrem Fahrzeug wasserdicht oder wassergeschützt sind, bevor Sie in nasser Umgebung fahren.

AVC – ACTIVE VEHICLE CONTROL

Die AVC Technologie ist die neueste Spektrum RC Innovation von Horizon Hobby. Dieses Spektrum Stabilisierungssystem ermöglich ein vollkommen neues Level der Fahrzeugbeherrschung. Die AVC Technologie nutzt dazu Sensoren die Gas und Lenkung beeinﬂussen und für ein erheblich stabileres und kontrolliertes Fahrerlebnis sorgen.

HINWEIS: Sie müssen mit dem SR4210 Empfänger Digitalservos verwenden. Analoge Servos reduzieren die Systemleistung und könnten überhitzen.

+ 36 hidden pages