Horizon Hobby blade 230 s Instruction Manual

Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni

RTF

2

EN

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before
operating. Failure to operate the product correctly can result in damage to the product, personal property and

cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage
to the product or other property. This product is not intended for use by children without direct adult supervision. Do
not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow
all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid
damage or serious injury.

The following terms are used throughout the product literature to indicate various levels of potential harm when
operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no
possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a
possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,
and serious injury OR create a high probability of superfi cial injury.

• Always keep a safe distance in all directions around
your model to avoid collisions or injury. This model is
controlled by a radio signal subject to interference from
many sources outside your control. Interference can
cause momentary loss of control.

• Always operate your model in open spaces away from
full-size vehicles, traffi c and people.

• Always carefully follow the directions and warnings for
this and any optional support equipment
(chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything
electrical out of the reach of children.

• Always avoid water exposure to all equipment not
specifi cally designed and protected for this purpose.
Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as it
could cause serious injury or even death.

• Never operate your model with low transmitter
batteries.

• Always keep aircraft in sight and under control.

• Always move the throttle fully down at rotor strike.

• Always use fully charged batteries.

• Always keep transmitter powered on while aircraft is
powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon
Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

Safety Precautions and Warnings

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in

a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to
ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards,
but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with
DSM or Spektrum.

3

EN

Box Contents

• Blade 230 S

• 800mAh 3S 11.1V 30C Li-Po Battery

• 3S Li-Po Balancing Charger with AC to DC Adapter

• DXe Transmitter (RTF Only)

• 4 AA Batteries (RTF Only)

Table of Contents

Length

18.66 in (474mm)

Height

6.46 in (164 mm)

Main Rotor Diameter

21.10in (536mm)

Tail Rotor Diameter

3.25 in (82.5mm)

Flying Weight

11.95oz (339 g)

Specifications

Components RTF BNF

Airframe

Blade® 230 S

Included Included

Main Motor

3900Kv Brushless

Installed Installed

Tail Motor

3600Kv Brushless

Installed Installed

Receiver

Spektrum™ AR636 Receiver

Installed Installed

ESC

Dual Brushless ESC

Installed Installed

Battery

800mAh 3S 11.1V 30C Li-Po

Included Included

Charger

3S 0.8A Li-Po Balancing Charger with AC to DC Adapter

Included Included

Transmitter

DSM2®/DSMX® Compatible Transmitter

DXe Included Required

To register your product online,visit www.bladehelis.com

Safety Precautions and Warnings ...................................... 2

Table of Contents .............................................................. 3

Box Contents .................................................................... 3

First Flight Preparation ...................................................... 4

Flying Checklist ................................................................4

Charging Warnings............................................................4

Battery Charging ............................................................... 4

Installing the DXe Transmitter Batteries (RTF) .................... 5

DXe Transmitter Control (RTF) ...........................................5

Transmitter Setup Table (BNF) ........................................... 6

Installing the Flight Battery ...............................................8

Transmitter and Receiver Binding ...................................... 8

Safe

®

Technology .............................................................. 9

Flight Mode and Rate Selection ......................................... 9

Panic Recovery .................................................................9

Throttle Hold ................................................................... 10

Control Tests ................................................................... 10

Understanding the Primary Flight Controls ......................11

Flying the 230 S.............................................................. 12

Advanced Settings ..........................................................12

Servo Adjustment ........................................................... 14

Post-Flight Inspection and Maintenance Checklist ........... 15

Troubleshooting Guide ....................................................15

Exploded View ................................................................ 17

Parts Listings .................................................................. 17

Optional Parts .................................................................18

Limited Warranty ............................................................ 18

Warranty and Service Contact Information ......................19

FCC Information .............................................................. 20

IC Information .................................................................20

Compliance Information for the European Union .............. 20

4

EN

NOTICE: Charge only batteries that are cool to the touch
and are not damaged. Look at the battery to make
sure it is not damaged e.g., swollen, bent, broken or
punctured.

1. Connect the AC to DC adapter to an AC outlet.

2. Connect the AC to DC adapter to the charger.

3. Connect the battery balance lead to the charger.
The connector is keyed to prevent reverse
polarity connection.

4. Always disconnect the fl ight battery from the charger
immediately upon completion of charging.

LED Indicators

R ed Flashing LED: Input power with no battery

connected

R ed and Green Solid LEDs: Battery connected and

charging

Red Solid LED: Charge complete
Red and Green Flashing LEDs: Charge error

Charging a fully discharged (not over-discharged) 800mAh
battery takes approximately 1–1.5 hours.
The charger can also be powered through the DC alligator
clips. Connect them to a 11.5–15V DC power source, not­ing proper polarity.

CAUTION: Do not connect to AC and DC power

sources at the same time. Doing so may cause
a short circuit, resulting in damage to the product,
personal injury or property damage.

NOTICE: Always connect cable polarities correctly.
Consult the battery instructions, safety sheet or product
support before using a 12V battery with sources other
than a standard AC wall outlet.

CAUTION: All instructions and warnings

must be followed exactly. Mishandling of Li-Po
batteries can result in a fi re, personal injury and/or
property damage.

• NEVER LEAVE CHARGING BATTERIES UNATTENDED.

• NEVER CHARGE BATTERIES OVERNIGHT.

• By handling, charging or using the included Li-Po
battery, you assume all risks associated with lithium
batteries.

• If at any time the battery begins to balloon or swell,
discontinue use immediately. If charging or discharging,
discontinue and disconnect. Continuing to use, charge
or discharge a battery that is ballooning or swelling can
result in fi re.

• Always store the battery at room temperature in a dry
area for best results.

• Always transport or temporarily store the battery in a
temperature range of 40–120º F (5–49° C).

• Do not store battery or model in a car or direct sunlight.
If stored in a hot car, the battery can be damaged or
even catch fi re.

• Always charge batteries away from fl ammable
materials.

• Always inspect the battery before charging

• Always disconnect the battery after charging, and
let the charger cool between charges.

• Always constantly monitor the temperature of the
battery pack while charging.

• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO
CHARGE LI-PO BATTERIES. Failure to charge the battery
with a compatible charger may cause a fi re resulting in
personal injury and/or property damage.

• Never discharge Li-Po cells to below 3V under load.

• Never cover warning labels with hook and loop strips.

• Never charge batteries outside recommended levels.

• Never charge damaged batteries.

• Never attempt to dismantle or alter the charger.

• Never allow minors to charge battery packs.

• Never charge batteries in extremely hot or cold places
(recommended between 40–120° F or
(5–49° C) or place in direct sunlight.

Charging Warnings

Battery Charging

First Flight Preparation

• Remove and inspect contents

• Begin charging the fl ight battery

• Program your computer transmitter (BNF only)

• Install the fl ight battery in the helicopter
(once it has been fully charged)

• Bind your transmitter (BNF only)

• Familiarize yourself with the controls

• Find a suitable area for fl ying

Flying Checklist

❏ Always turn the transmitter on fi rst

❏ Plug the fl ight battery into the lead from the ESC
❏ Allow the receiver and ESC to initialize and arm properly
❏ Fly the model
❏ Land the model
❏ Unplug the fl ight battery from the ESC

❏ Always turn the transmitter off last

5

EN

Fli ght Mode Switch

0 = Stability Mode (NORM)
1 = Intermediate Mode (FM1)
2 = Agility Mode (FM2)

Bind/Panic Switch

Throttle Hold
Du al Rate Switch

Installing the DXe Transmitter Batteries (RTF)

DXe Transmitter Control (RTF)

The LED indicator fl ashes and the transmitter
beeps progressively faster as the battery voltage
drops.

Replace the transmitter batteries when the
transmitter begins to beep.

A

B

C

D

E

F

G

LED Indicator

ABCDEF G

Mode 1

Aileron (Left/Right)
Throttle (Up/Down)

Throttle
Trim

Aileron
Trim

ON/OFF
Switch

Rudder
Trim

Elevator
Trim

Rudder (Left/Right)
Elevator (Up/Down)

Mode 2

Aileron (Left/Right)
Elevator (Up/Down)

Elevator
Trim

Aileron
Trim

ON/OFF
Switch

Rudder
Trim

Throttle
Trim

Rudder (Left/Right)
Throttle (Up/Down)

6

EN

Transmitter Setup Table (BNF)

D/R & Expo

Chan

Switch Pos

(Ail D/R) D/R Expo

AILE

0 100/100 +25
1 100/100 +25
2 75/75 +25

ELEV

0 100/100 +25
1 100/100 +25
2 75/75 +25

RUDD

0 100/100 +25
1 100/100 +25
2 75/75 +25

Throttle Hold

Throttle 0%

D/R & Expo
Chan Sw Pos D/R Expo

AILE

0 100 +25
1 75 +25

ELEV

0 100 +25
1 75 +25

RUDD

0 100 +25
1 75 +25

Mix 1

GYRO->GYRO ACT
Rate D+125% U+125%
SW ELE D/R TRIM – INH

Timer

Mode Count Down
Time 5:00 Tone
Start Throttle Out
Over 25%

Timer
Down Timer 5:00
Switch THR CUT

SYSTEM SETUP

Model Type HELI
Swash Type 1 servo

Normal

F-Mode Setup
Flight Mode F Mode
Hold Hold

SW Select

Trainer Aux 2
F Mode Gear
Gyro INH
Mix INH
Hold INH
Knob INH

Frame Rate

11ms

DSMX

Chan Travel Reverse

THR 100/100 Normal
AIL 100/100 Normal
ELE 100/100 Normal
RUD 100/100 Normal

Chan Travel Reverse

GER 100/100 Normal
PIT 100/100 Normal
AX2 100/100 Normal

Servo Setup

FUNCTION LIST

ADJUST LISTSETUP LIST

DX6i

DX7s, DX8

Throttle Curve

Switch Pos

(F Mode)

Pos 1Pos 2Pos 3Pos 4Pos

5

NORM 0 25 50 75 100

STUNT 100 90 85 90 100

Throttle Curve

Switch Pos

(F Mode) Pt 1 Pt 2 Pt 3 Pt 4 Pt 5

N 0 25 50 75 100
1 100 80 75 80 100
2 100 90 85 90 100

TRAVEL ADJ
Channel Travel

THRO 100/100
AILE 100/100
ELEV 100/100
RUDD 100/100
GYRO 100/100
PITC 100/100

REVERSE
Channel Direction

THRO N
AILE N
ELEV N
RUDD N
GYRO N
PITC R

GYRO

RATE SW-F.MODE

0 88% NORM 0
1 12% STUNT 1

Modulation Type

AUTO DSMX-ENABLE

D/R COMBI

D/R SW AILE

Model Type HELI

Swash Type

1 servo
Normal

Pitch Curve

Switch Pos

(F Mode)

Pos 1Pos 2Pos 3Pos 4Pos

5

NORM 30 40 50 75 100

STUNT 0 25 50 75 100

HOLD 25 37 50 75 100

Pitch Curve
Switch Pos

(F Mode) Pt 1 Pt 2 Pt 3 Pt 4 Pt 5

N 30 40 50 75 100
1 0 25 50 75 100
2 0 25 50 75 100

HOLD 25 37 50 75 100

Panic Mode Operation

ELEV D/R Switch

Sw Pos 0 = Panic Mode Off
Sw Pos 1 = Panic Mode On

Once the model has returned to level you must manually return the Panic Mode
Switch to the off position otherwise the cyclic and tail rotor controls will be reduced.

Panic Mode Operation

Trainer/Bind Button

Pressed = Panic Mode On
Released = Panic Mode Off

7

EN

D/R & Expo Throttle Curve
Chan Sw (F) Pos D/R Expo Sw (B) Pos Pt 1 Pt 2 Pt 3 Pt 4 Pt 5

AILE

0 100/100 +25 N 0 25 50 75 100
1 100/100 [phone]
2 75/75 [phone]

ELEV

0 100/100 +25 Pitch Curve
1 100/100 +25

Sw (B) Pos Pt 1 Pt 2 Pt 3 Pt 4 Pt 5

2 75/75 +25 N 30 40 50 75 100

RUDD

0 100/100 [phone]
1 100/100 [phone]
2 75/75 +25 HOLD 25 37 50 75 100

Gyro

Inhibit

D/R & Expo Throttle Curve
Chan Sw (F) Pos D/R Expo Sw (B) Pos Pt 1 Pt 2 Pt 3 Pt 4 Pt 5

AILE

0 100/100 +25 N 0 25 50 75 100
1 100/100 [phone]
2 75/75 [phone]

ELEV

0 100/100 +25 Pitch Curve
1 100/100 +25

Sw (B) Pos Pt 1 Pt 2 Pt 3 Pt 4 Pt 5

2 75/75 +25 N 30 40 50 75 100

RUDD

0 100/100 [phone]
1 100/100 [phone]
2 75/75 +25 HOLD 25 37 50 75 100

Gyro

Inhibit

Mixing

P-Mix 1

Normal
Channels -I- > Ger
Rate 0/–125
Offset 100
Switch Switch I
Position 0

1

Timer

Mode Count Down
Time 5:00
Start Throttle Out
Over 25%
One Time Inhibit

SYSTEM SETUP

Model Type HELI
Swash Type Normal

F-Mode Setup
Switch 1 Switch B
Switch 2 Inhibit
Hold Switch Switch H

RX Port Assignments

1 Throttle
2 Aileron
3 Elevator
4 Rudder
5 Flight Mode Switch B
6 Collective

Frame Rate

11ms

DSMX

Chan Travel Reverse

THR 100/100 Normal
AIL 100/100 Normal
ELE 100/100 Normal

Chan Travel Reverse

RUD 100/100 Normal
GER 100/100 Normal
PIT 100/100 Normal

Chan Travel Reverse

THR 100/100 Normal
AIL 100/100 Normal
ELE 100/100 Normal
RUD 100/100 Normal
GER 100/100 Normal

Chan Travel Reverse

PIT 100/100 Normal
AX2 100/100 Normal
AX3 100/100 Normal
AX4 100/100 Normal

Servo Setup

Servo Setup

FUNCTION LIST

FUNCTION LIST

DX6

DX7 (new), DX9, DX18

Panic Mode Operation

Bind / I Button

Pressed = Panic Mode On
Released = Panic Mode Off

Panic Mode Operation

Bind / I Button

Pressed = Panic Mode On
Released = Panic Mode Off

Timer

Mode Count Down
Time 5:00
Start Throttle Out
Over 25%
One Time Inhibit

SYSTEM SETUP

Model Type HELI
Swash Type Normal

F-Mode Setup
Switch 1 Switch B
Switch 2 Inhibit
Hold Switch Switch H

0

1

Channel Assign

Channel Input

1 Throttle
2 Aileron
3 Elevator
4 Rudder
5 Gear Switch B
6 Collective
7 AUX 2 Switch I

Frame Rate

11ms

DSMX