Horizon Fitness Treadmill User Manual
Horizon Fitness
800 Burton Blvd
DeForest, Wisconsin 53532
Ph: 1-888-993-3199 Fax: 1-608-842-1660
www.horizonfitness.com
In the event that a problem should arise,
DO NOT RETURN TO THE STORE,
please contact:
Horizon Fitness @ 1-888-993-3199
or
www.horizonfitness.com
Rev. 1.5
COMMON PRODUCT QUESTIONS
Are the sounds my treadmill makes normal?
All treadmills make a certain type of thumping noise due to the
belt riding over the rollers, especially new treadmills. This noise
will diminish over time, although may not totally go away. Over
time, the belt will stretch, causing the belt to ride smoother over
the rollers.
Why is the treadmill I had delivered louder than the one at the
store?
All fitness products seem quieter in a large store showroom
because there is generally more background noise than in your
home. Also, there will be less reverberation on a carpeted concrete floor than on a wood overlay floor. Sometimes a heavy
rubber mat will help reduce reverberation through the floor. If a
fitness product is placed close to a wall, there will be more
reflected noise.
When should I be worried about a noise?
As long as the sounds your treadmill makes are no louder than a
normal conversational tone of voice, it is considered normal noise.
If your treadmill is louder than this, you may want to call your
service technician. Sometimes an initial diagnosis can be made
over the phone.
MAINTENANCE
What kind of routine maintenance is required?
We use sealed bearings throughout our treadmill so
lubrication is not needed. The most important maintenance step is
to simply wipe your perspiration off the treadmill after each use.
How do I clean my Horizon Fitness Treadmill?
Clean with soap and water cleaners only. Never use
solvents on plastic parts.
Tensioning the running belt
If you can feel a slipping sensation when running on the treadmill,
the running belt must be tightened. In most cases, the belt has
stretched from use, causing the belt to slip. This is a normal and
common adjustment. To eliminate this slipping, tension both the
rear roller bolts with the appropriate sized Allen wrench (Alpine 8mm, Paragon II/Quantum II/Omega II - 6mm), turning it 1/4
TURN as shown below. Try the treadmill again to check for slipping. Repeat if necessary, but NEVER TURN the roller bolts more
than 1/4 turn at a time. The belt tension is set properly when the
running belt is 1/4 of an inch from the deck.
If the belt is too far to the left side:
1. Turn the left roller bolt 1/4 turn
clockwise (tighten).
2. Turn the right roller bolt 1/4 turn
counterclockwise (loosen).
If the belt is too far to the right
side:
1. Turn the right roller bolt 1/4 turn
clockwise (tighten).
2. Turn the left roller bolt 1/4 turn
counterclockwise (loosen).
Centering the belt
If the running belt is too far to the right side, use the
supplied Allen wrench to turn the right tension bolt
clockwise 1/4 turn at a time until the belt remains centered
during use.
tension
tension
IMPORTANT SAFETY INSTRUCTIONS.
SAVE THESE INSTRUCTIONS
Read all instructions before using this Treadmill.
When using an electrical product, basic precautions
should always be followed, including the following:
Read all instructions before using this HORIZON
FITNESS Treadmill
WARNING! Connect this exercise product to
a properly grounded outlet only. See grounding
instructions.
GROUNDING INSTRUCTIONS
This product must be grounded. If a treadmill
should malfunction or breakdown, grounding
provides a path of least resistance for electrical
current to reduce the risk of electrical shock. This
product is equipped with a cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in
accordance with local codes and ordinances.
DANGER! Improper connection of the equipment-
grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or
serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify the
plug provided with the product. If it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.
This product is for use on a nominal 120-volt cir-
cuit, and has a grounding plug that looks like the
plug illustrated below. A temporary adapter such as
the one illustrated below may be used to connect
this plug to a 2-pole receptacle as shown, if a prop-
erly grounded outlet is not available. The temporary
adapter should be used only until a properly
grounded outlet can be installed by a qualified
electrician. The green colored rigid ear, lug, or the
like extending from the adapter must be connected
to a permanent ground such as a properly grounded
outlet box cover. Whenever the adapter is used, it
must be held in place by a metal screw.
GROUNDED
TREADMILL
POWER CORD
3-POLE
GROUNDED
OUTLET
WARNING! To reduce the risk of burns, fire, electrical shock or injury to persons:
· Never use the treadmill before securing the safety tether clip to your clothing.
· If you experience chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and
consult your physician before continuing.
· Do not wear clothes that might catch on any part of the treadmill.
· Keep power cord away from heated surfaces.
· Keep children off of treadmill at all times.
· Do not use treadmill outdoors.
· Unplug treadmill before moving it.
· Do not remove the treadmill motor covers or roller covers. Service should be performed only by an
authorized Horizon Fitness service provider.
· Treadmill should be plugged into a dedicated 20amp circuit.
CHILDREN
• Keep children off your Treadmill at all times.
• When the Treadmill is in use, young children and pets should be kept at least 10 feet away.
CAUTION! If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising
immediately and consult your physician before continuing.
• Do not wear clothing that might catch on any part of the Treadmill.
• Read this Owner’s Guide before operating this Treadmill.
METAL
GROUNDING
SCREW
2-POLE
OUTLET IN
GROUNDED BOX
ADAPTOR
Assembly Guide
IMPORTANT SAFETY
INSTRUCTIONS SAVE
THESE INSTRUCTIONS
ALPINE, PARAGON II, QUANTUM II & OMEGA II
1.888.993.3199 or www.horizonfitness.com
Congratulations on choosing a Horizon
Fitness Treadmill. You’ve taken an important
step in developing and sustaining an
exercise program! Your Horizon Fitness
Treadmill is a tremendously effective
tool for achieving your personal fitness
goals. Regular use of your Horizon
Fitness Treadmill can improve the
quality of your life in so many ways.
Here are just a few of the health
benefits of aerobic exercise:
• Weight Loss
• A Healthier Heart
• Improved Muscle Tone
• Increased Daily Energy Levels
• Reduced Stress
• Help In Countering Anxiety
and Depression
• An Improved Self Image
The key to reaping these
benefits is to develop the
exercise habit. Your new
Horizon Fitness Treadmill
will help you eliminate the
obstacles that prevent you
from getting in your
exercise time. Inclement
weather and darkness
won't interfere with your
workout when you use
your Horizon Fitness
Treadmill in the comfort
of your home. This
manual provides you
with basic information
for using and enjoying
your new machine. A more
complete knowledge of your
new Horizon Fitness Treadmill
will assist you in realizing your
goal of a healthy lifestyle.
CAUTION:
BEFORE
BEGINNING
ANY EXERCISE
PROGRAM, ALWAYS
CONSULT YOUR
PHYSICIAN.
IF YOU EXPERIENCE
CHEST PAINS, NAUSEA,
DIZZINESS OR SHORT-
NESS OF BREATH, STOP
EXERCISING AND
CONSULT YOUR
PHYSICIAN BEFORE
CONTINUING.
GETTING STARTED
To avoid possible damage to this Treadmill, please follow
these assembly steps in the correct order. Before pro-
ceeding, find your Treadmill’s serial number and model
name located to the left of the on/off power switch and
power cord and enter it in the space provided below:
Refer to this number when calling for service, and also
enter this serial number on your Warranty Card and in
your own records. Be sure to read the Safety Instructions
and Owner’s Guide before using your new Horizon
Fitness Treadmill.
SERIAL NUMBER AND MODEL
NAME LOCATION:
EXCLUSIONS AND LIMITATIONS
This warranty applies only to the original owner and
is not transferable. This warranty is expressly limited
to the repair or replacement of a defective frame,
motor, electronic component, or defective part and is
the sole remedy of the warranty. The warranty does
not cover normal wear and tear, improper assembly
or maintenance, or installation of parts or accessories
not originally intended or compatible with the
Treadmill as sold. The warranty does not apply to
damage or failure due to accident, abuse, corrosion,
discoloration of paint or plastic, or neglect. Horizon
Fitness shall not be responsible for incidental or consequential damages. All returns must be pre-authorized by Horizon Fitness. Horizon Fitness’ obligation
under this warranty is limited to replacing or repairing, at Horizon Fitness’ option, the product at one of
its authorized service centers. An Horizon Fitness
authorized service center must receive all products
for which a warranty claim is made. These products
must be received with all freight and other transportation charges prepaid, accompanied by sufficient
proof of purchase. Parts and electronic components
reconditioned to As New Condition by Horizon
Fitness or its vendors may sometimes be supplied as
warranty replacement parts and constitute fulfillment
of warranty terms. This warranty gives you specific
legal rights, and your rights may vary from state to
state.
WARRANTY REGISTRATION
Your warranty card must be completed and sent to
Horizon Fitness or register on line at www.horizonfitness.com, before a warranty claim can be processed.
LIMITED HOME USE WARRANTY
FRAME - LIFETIME
Horizon Fitness warrants the frame against defects in
workmanship and materials for the lifetime of the
original owner.
DRIVE MOTOR - 10 year
Horizon Fitness warrants the drive motor against
defects in workmanship and materials for a period of
ten years from the date of purchase, so long as the
device remains in the possession of the original
owner.
ELEVATION MOTOR - 10 year
Horizon Fitness warrants the elevation motor against
defects in workmanship and materials for a period of
ten years from the date of purchase, so long as the
device remains in the possession of the original
owner.
ELECTRONICS & PARTS - 1 year
Horizon Fitness warrants the electronic components
and all original parts for a period of one year from
the date of original purchase, so long as the device
remains in the possession of the original owner.
LABOR - 1 year
Horizon Fitness shall cover the labor cost for the
repair of the device for a period of one year from the
date of the original purchase, so long as the device
remains in the possession of the original owner.
In the event that a problem should arise,
DO NOT RETURN TO
THE STORE,
please contact:
Horizon Fitness
@
1.888.993.3199
or
www.horizonfitness.com
treadmillv1.5.qxd 9/13/2001 2:33 PM Page 1
TREADMILL
Grip Pusle
Handlebars
Power Cord
Console Mast
Console Cable
Water Bottle Holder
Console Assembly
Safety Key
STEP 1
Install Console Assembly
a. Lift the console masts into the
upright position.
b. Align the console masts with
the holes in the base bracket.
Make sure that the console
masts are inserted completely
into the base bracket.
c. Insert a 60mm bolt (A) with a
16mm washer (B) and a 13mm
nylon nut (C) into the outside
base bracket holes on both the
left and right sides. Secure
using a 5mm Allen wrench and
13mm flat wrench. Tighten the
pre-installed 60mm bolt on
both the left and right base
brackets.
d. Insert a 16mm bolt (D) and arc
washers (H) into the front of the
base bracket on both the right
and left sides. Secure with a
5mm Allen wrench.
STEP 2
Install the Console Assembly
a. Tilt the console assembly back,
and lower the console assembly
into place by sliding the
console assembly axles into the
receiving tubes. Align the left
and right console assembly
brackets holes with the holes in
front of the console mast. Be
sure not to pinch the console
cable when lowering the
console assembly into place.
b. Insert a 20mm bolt (E) for both
the left and right console
assembly brackets.
STEP 3
Attach Console Assembly
a. Make sure the console assembly
is pressed down completely.
Insert a 15mm bolt (F) into the
back of the console mast to
secure the console assembly
on both the left and right sides.
Secure with a 5mm Allen wrench.
Tighten the pre-installed bolts
(G) on bolt the left and right
sides.
b. Insert the 2 water bottle holders
into the console.
CUSTOMER ASSISTANCE CENTER 1.888.993.3199
or www.horizonfitness.com
ASSEMBLY
GUIDE
Base Bracket
Levelers
NOTE: The assembly picture may not represent your exact treadmill model
F
G
E
A
D
H
B
C
Safety Key
Holder
UNPACKING
Unpack your treadmill and the contents
inside the box. Do not attempt to move
the treadmill until it is completely assembled. Leave the treadmill in the bottom
portion of the treadmill box to assemble.
Unpack your treadmill where you will be
using it. Place your treadmill on a level
flat surface. It is recommended that you
place a protective covering on your floor.
Your treadmill will arrive almost completely assembled. You will only need to
attach the following items. Verify that the
following parts and tools are included:
Parts
•1 Power Cord
(Alpine/Paragon II)
•1 Safety Key
•2 Water Bottle
Holders
•1 Hardware
Pack (contents
listed below)
B) Base Bracket
16mm washer
Quantity: 2
H) Arc Washer
Quantity: 2
E) Console Assembly Bracket
20mm long bolt
Quantity: 2
D) Base Bracket
16mm bolt
Quantity: 2
A) Base Bracket
60mm bolt
Quantity: 2
C) Base Bracket
13mm nylon nut
Quantity: 2
F) Console Assembly
15mm bolt
Quantity: 2
Hardware (Actual Size)
Tools
•5mm Allen Wrench/
Phillips Screw Driver
•Flat Wrench
•8mm Allen Wrench
(Alpine)
•6mm Allen Wrench
(Paragon II, Quantum II
& Omega II)
NOTE: It is recommended that you apply grease
to the threads of each bolt as you assemble
your Treadmill, to prevent loosening and noise.
Also, during each assembly step, ensure that
ALL nuts and bolts are in place and partially
threaded in before completely tightening any
ONE bolt.
treadmillv1.5.qxd 9/13/2001 2:33 PM Page 2
Loading...