Horizon Fitness T-PRO Owner's Manual

TREADMILL OWNER’S MANUAL

Read the TREADMILL GUIDE before using this OWNER’S MANUAL.

T-PRO

2

3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an electrical product, basic precautions should always be followed, including the following: Read all instructions
before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of
all warnings and precautions. If you have any questions after reading this manual, contact your local dealer.

4

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Never use the treadmill before securing the safety tether clip to your clothing.

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop
exercising immediately and consult your physician before continuing.

• When exercising, always maintain a comfortable pace.

• Do not wear clothes that might catch on any part of the treadmill.

• Always wear athletic shoes while using this equipment.

• Do not jump on the treadmill.

• At no time should more than one person be on treadmill while in operation.

• This treadmill should not be used by persons weighing more than Max. user weight. Failure to comply will void the warranty.

• When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck.

• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth
only; never use solvents. (See MAINTENANCE)

• The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or
taking off parts.

• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

• Connect this exercise product to a properly grounded outlet only.

WARNING

TO REDUCE THE RISK OF ELECTRICAL SHOCK:

Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or
taking off parts.

DANGER

5

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• At NO time should pets or children under the age of 13 be closer to the treadmill than 10 feet.

• At NO time should children under the age of 13 use the treadmill.

• Children over the age of 13 or disabled persons should not use the treadmill without adult supervision.

• Use the treadmill only for its intended use as described in the treadmill guide and owner’s manual.

• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.

• Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
immersed in water. Return the treadmill to a service center for examination and repair.

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair, and the like.

• To prevent electrical shock, never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Do not use treadmill in any location that is not temperature controlled, such as but not limited to porches, pool rooms, bathrooms,
car ports or outdoors. Failure to comply may void the warranty.

• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.
Failure to comply will void the warranty.

• Do not remove the console covers unless instructed by your local dealer. Service should only be done by an authorized service
technician

It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder
temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before
first time use. Failure to do so may cause premature electronic failure.

WARNING

6

GROUNDING INSTRUCTIONS

This product must be grounded. If a treadmill should malfunction or break down, grounding provides a path of least resistance
for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with local codes and ordinances.

Connect this exercise product to a properly grounded outlet only.
Never operate product with a damaged cord or plug even if it is working

properly. Never operate any product if it appears damaged, or has been
immersed in water. Contact your local dealer for replacement or repair.

3-POLE

GROUNDED

OUTLET

GROUNDING PIN

WARNING

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 220 Volt circuit and has a grounding plug that looks like the plug in the illustration. Make sure
that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.

This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and
observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one
circuit. This treadmill should be used with a minimum 10-amp circuit.

7

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the
treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmill’s serial number and model name located on a
white barcode sticker near the on/off power switch and power cord and enter them in the
space provided below.

ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

SERIAL NUMBER:

TM

WARNING

SERIAL NUMBER LOCATION

MODEL NAME: HORIZON TREADMILL

8

USB PORT

WATER BOTTLE HOLD ER

GRIP PULSE H ANDR AIL S

CONSOLE

ON/OFF SWITCH

CIRCUIT BREAKER

TRANSPORT WHEEL

POWER CORD

RE AD IN G R AC K

HAN DL EB AR S

CON SO LE CON TR OL S A ND DISPL AY WI ND OW S

AUDIO I N / OUT JACK S

SAFET Y KEY PLACEMEN T

MOTOR COVER

SIDE RAIL

ROLLE R END CA P

REAR ROLLER

TENSION/ADJUSTMENT BOLTS

CONSOLE MAST

RUNNI NG BELT / RUNNING D ECK

T-PRO

Max. User Weight: 182 kg / 400 lbs
Product Weight: 130 kg / 286 lbs
Overall Dimensions: 196.5 x 95.5 x 151 cm / 77.5” x 37.5”x 59.5”

9

TOOLS INCLUDED:

F 5 mm T-Wrench
F 8 mm T-Wrench
F Screwdriver

PARTS INCLUDED:

F 1 Console Assembly
F 2 Handlebars
F 2 Console Masts
F 1 Hardware Kit
F 1 Safety Key
F 1 USB Cover
F 1 Audio Adapter Cable
F 1 Power Cord
F 1 Bottle of Silicone Lubricant
F 4 Console Mast Covers

If you have questions or if

there are any missing parts,

contact your local dealer.

Contact information is located

on the back panel of this

manual.

NEED HELP?

DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.

WARNING

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Once the banding straps have been removed, do not transport this unit unless it is
fully assembled. Unpack and assemble the unit where it will be used. Never grab hold of
any portion of the incline frame and attempt to lift or move the treadmill. Lift the treadmill
from the roller end caps area while a second person removes the parts packed under
the treadmill.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

WARNING

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.

PRE ASSEMBLY

10

BOLTS (A)

SPRING
WASHERS (B)

LEFT CONSOLE MAST

ARC WASHER S (C)

MAIN FRAME BRACKET

RIGHT CON SOLE MAST

LEAD WIRE

CONSOLE CABLE

T-PRO ASSEMBLY STEP 1

A Open haRdwaRe fOR sTeP 1.

B Pull lead wiRe through RighT cOnsOle masT.

After pulling the lead wiRe through the mast, the
top of the cOnsOle cable should be located at
the top of the mast. Detach and discard lead wiRe.

C Place RighT cOnsOle masT over main fRame

bRackeT.

D Attach cOnsOle masT to main fRame

bRackeT using 4 bOlTs (a), 4 sPRing
washeRs (b) and 4 aRc washeRs (c).

E Repeat steps C–D on other side.

NOTE: Do not pinch console cable when placing
the mast onto the main frame bracket.

BOLT (A)
20 mm
Qty: 8

SPRIN G WASHER (B)

8.2 mm
Qty: 8

ARC WASHER (C)

8.4 mm
Qty: 8

HARDWARE FOR STEP 1 :

NOTE: Do not tighten bolts until step 3 is complete.

11

T-PRO ASSEMBLY STEP 2

A Open haRdwaRe fOR sTeP 2.

B Feed handlebaR cable through

cOnsOle masT bRackeT and out through
the top of cOnsOle masT.

C Slide handlebaR onto cOnsOle masT

bRackeT and attach using 3 bOlTs (a),
3 sPRing washeRs (b) and 3 flaT
washeRs (d).

D Repeat on other side.

BOLT (A)
20 mm
Qty: 6

SPRIN G WASHER (B)

8.2 mm
Qty: 6

FLAT WASHER (D)

8.2 mm
Qty: 6

HARDWARE FOR STEP 2 :

BOLTS (A)

SPRING WASHERS (B)

HANDLEBAR CABLE

CONSOLE MAST

FLAT WASHERS (D)

HANDLEBAR S

CONSOLE MAST BRACKET

NOTE: Be careful not to pinch any wires
while attaching the handlebars.