Horizon Fitness T901 User Manual

PREMIER SERIES

TREADMILL USER’S GUIDE

FOR MODEL :

T901

T901_Rev.2.0.indd 1 9/10/08 11:15:14 AM

BEFORE

YOU BEGIN

ASSEMBLY

INTRODUCTION

IMPORTANT

PRECAUTIONS

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

CONGRATULATIONS and THANK YOU for your purchase of this Premier Series Treadmill!

Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, a Premier Series treadmill can help you attain it – adding club-quality performance to your at-home workouts, with the ergonomics and innovative features you need to get stronger and healthier, faster. Because we're committed to designing fitness equipment from the inside out, we use only the highest quality components. It's a commitment we back with one of the strongest frame-to-motor warranty packages in the industry.

You want exercise equipment that offers the most comfort, the best reliability and the highest quality in its class.

Horizon Premier Series Treadmills deliver.

IN TRODUCTION

Important Precautions

Assembly

Before You Begin

Treadmill Operation

Conditioning Guidelines

Troubleshooting & Maintenance

Limited Warranty

CONTACT INFORMATION

Back Panel

TA B L E OF CONTENTS

T901_Rev.2.0.indd 2-3 9/10/08 11:15:14 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY

BEFORE

YOU BEGIN

ASSEMBLY

INTRODUCTION

IMPORTANT

PRECAUTIONS

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets.

It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.

OPERATION

To reduce the risk of damaging important components on your treadmill, it is strongly recommended that your treadmill is plugged into a dedicated 20 amp circuit, without the use of an additional extension cord and/or power strip. Failure to comply may void the warranty.

To reduce the risk of burns, fire, electrical shock or injury to persons:

SAVE THESE INSTRUCTIONS

Read all instructions before using this treadmill. When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. If you have any questions after reading this manual, contact Customer Tech Support at the number listed on the back panel of this manual.

Connect this exercise product to a properly grounded outlet only. See grounding instructions.

GROUNDING INSTRUCTIONS

This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least speed for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 110-volt circuit and has a grounding plug that looks like the illustration below. This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one circuit. It is recommended that the treadmill be used with a 20 amp circuit for optimal performance.

IM PO RTANT P REC AUTIONS

WARNING

3-Pole Grounded Outlet

GROUNDED TREADMILL POWER CORD

At NO time should pets or children under the age of 12 be closer to the treadmill than 10 feet. At NO time should children under the age of 12 use the treadmill. Children over the age of 12 should not use the treadmill without adult supervision.

• Never use the treadmill before securing the safety tether clip to your clothing.

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing.

• Do not wear clothes that might catch on any part of the treadmill.

• Always wear athletic shoes while using this equipment.

• Do not jump on the treadmill.

• Keep power cord away from heated surfaces.

• Do not insert or drop any object into any opening.

• Unplug treadmill before moving or cleaning it. To clean, wipe surfaces down with soap and slightly damp cloth only; never use solvents. (See MAINTENANCE)

• At no time should more than one person be on treadmill while in operation.

• This treadmill should not be used by persons weighing more than 325 pounds. Failure to comply will void the warranty.

• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.

• Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty.

• Use the treadmill only as described in this manual.

OTHER SAFETY TIPS FOR YOUR TREADMILL

T901_Rev.2.0.indd 4-5 9/10/08 11:15:16 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY

BEFORE

YOU BEGIN

ASSEMBLY

INTRODUCTION

IMPORTANT

PRECAUTIONS

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

ASSEMBLY

IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!

During the assembly process of the treadmill there are several areas that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. There should be no side-to-side play in the console masts or any forward and back play in the console assembly or handlebars. If there is any play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position or until specified in the assembly instructions. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

Before proceeding, find your treadmill’s serial number and model name located to the left of the on/off power switch and power cord and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOxES BELOW:

SERIAL NUMBER:

MODEL NAME:

* Refer to the SERIAL NUMBER and MODEL NAME when calling for service. * Also enter this serial number on your Warranty Card.

LED DISPLAY WINDOWS

AUDIO-IN JACK

PULSE GRIPS

SUPPORT BAR

ON/OFF SWITCH

CIRCUIT BREAKER

TRANSPORT WHEEL

IPOD DOCKING STATION

HEADPHONE JACK

POWER CORD

HANDLEBAR

CONSOLE

MOTOR COVER

RUNNING BELT / RUNNING DECK

SIDE RAIL

ROLLER END CAP

CONSOLE MAST

REAR ROLLER

ADJUSTMENT BOLTS

SAFETY KEY PLACEMENT

WATER BOTTLE POCKET

TOOLS INCLUDED

PARTS INCLUDED

c 1 Console Assembly

(located under treadmill deck)

c 2 Console Masts c 2 Handlebars c 2 Support Bars c 2 Water Bottle Pockets c 6 Hardware Bags

c 1 Right Linkage Arm

If you have questions or if there are any missing parts, contact Customer Tech Support.

Contact information is located on the back panel of this manual.

For a complete exploded diagram, visit us at www.horizonfitness.com

c Screwdriver

c 5 mm T-wrench

c 10 mm L-wrench

c 6 mm T-wrench

c 10 mm/13 mm Flat Wrench

c 1 Safety Key c 1 Bottle of Silicone Lubricant c 3 iPod

Dock Inserts

c 1 Universal MP3 Player Dock Insert c 1 iPod

Docking Station Rubber Plug

c 1 Audio Adaptor Cable c 1 Power Cord

FOOT LOCK LATCH (UNDER DECK)

WARNING

T901_Rev.2.0.indd 6-7 9/10/08 11:15:18 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY

BEFORE

YOU BEGIN

ASSEMBLY

INTRODUCTION

IMPORTANT

PRECAUTIONS

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

PRE-ASSEMBLY

ASS E M B LY ST E P 1

FLAT WASHER (B) 20 mm Qty: 1

WAVY WASHER (F) 29 mm Qty: 1

BOLT (D) Qty: 1

BOLT (A) 15 mm Qty: 1

TEFLON WASHER (C) 18 mm Qty: 1

FLAT WASHER (E) 27 mm Qty: 1

HARDWARE BAG 1 CONTENTS :

TEFLON WASHER (C)

FLAT WASHER (B)

BOLT (A)

LEFT CONSOLE MAST

BOLT (D)

MAIN FRAME

LEFT LINKAGE ARM

FLAT WASHER (E)

WAVY WASHER (F)

ELEVATION FRAME

DO NOT ATTEMPT TO LIFT THE TREADMILL!* Do not move or lift

treadmill from packaging until specified to do so in the assembly instructions. Failure to do so may result in injury! Remove plastic wrap from console masts.

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

WARNING

Open HARDWARE BAG 1.

Move LEFT LINKAGE ARM into position. Insert 1 BOLT (A) and 1 FLAT WASHER (B) into LEFT LINKAGE ARM followed by 1 TEFLON WASHER (C) and attach to ELEVATION FRAME.

Lift LEFT CONSOLE MAST into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on its own.

Insert 1 BOLT (D) and 1 FLAT WASHER (E) through LEFT CONSOLE

MAST followed by 1 WAVY WASHER (F) and attach to MAIN FRAME.

NOTE: Do not completely tighten any screws or bolts until step 6 is complete!

* NOTE: If you have lifted the treadmill deck too far or attempted to move the machine and it has

sprung open and cannot be assembled, refer to the troubleshooting section in order to restore the treadmill to its proper position.

DO NOT

EXCEED

DEGREES!

Cut the yellow banding straps.

Raise the deck slightly – NO MORE THAN 45 DEGREES – to remove all contents from underneath the deck.

T901_Rev.2.0.indd 8-9 9/10/08 11:15:21 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY

BEFORE

YOU BEGIN

ASSEMBLY

INTRODUCTION

IMPORTANT

PRECAUTIONS

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

ELEVATION FRAME

PRE-ATTACHED BOLT

PRE-ATTACHED NUT

RIGHT LINKAGE ARM

BOLT (I)

TEFLON WASHER (J)

RIGHT CONSOLE MAST

PRE-ATTACHED TEFLON WASHER

ASS E M B LY ST E P 3

RIGHT HANDLEBAR

CONSOLE MASTS

BOLTS (K)

FLAT WASHERS (L)

ARC WASHERS (N)

SPRING WASHERS (M)

BOLTS (K)

CONSOLE CABLE

BOLT (K) 20 mm Qty: 6

FLAT WASHER (L) 8 mm Qty: 4

SPRING WASHER (M) 8 mm Qty: 6

ARC WASHER (N) 8 mm Qty: 2

HARDWARE BAG 3 CONTENTS:

CABLE HOLE

CONSOLE CABLE

RIGHT CONSOLE MAST

RIGHT HANDLEBAR

PULSE CABLE

POWER CABLE

CONSOLE CABLE

ASS E M B LY ST E P 2

Open HARDWARE BAG 2.

Attach LOCK LATCH PIN (G) to RIGHT FOLDING FRAME using T-wrench and tighten completely.

Pull LEAD WIRE through RIGHT CONSOLE MAST. After pulling the lead wire through the mast, the top of the console cable should be located at the top of the mast. Detach and discard lead wire.

Insert 1 BOLT (D) and 1 FLAT WASHER (E) through RIGHT CONSOLE MAST followed by 1 WAVY WASHER (F) and attach to MAIN FRAME.

Unscrew PRE-ATTACHED NUT and remove from RIGHT LINKAGE ARM and discard. Carefully move

RIGHT LINKAGE ARM and PRE-ATTACHED TEFLON WASHER into position to attach to ELEVATION FRAME.

While holding RIGHT CONSOLE MAST in the upright position, attach RIGHT LINKAGE ARM using BOLT (I) and TEFLON WASHER (J) as shown.

Open HARDWARE BAG 3.

With the running deck in the lowered position, place the RIGHT HANDLEBAR on top of the RIGHT CONSOLE MAST. Carefully route the CONSOLE CABLE through the bottom of the handlebar and out the CABLE HOLE as shown in second drawing below. The

PULSE CABLE and POWER CABLE should be pulled out of

the hole as well.

NOTE: Do not pinch the CONSOLE CABLE when placing

right handlebar on top of the RIGHT CONSOLE MAST.

To assemble the RIGHT

HANDLEBAR to the RIGHT CONSOLE MAST, insert 2 BOLTS (K), 2 SPRING WASHERS (M) and 2 FLAT WASHERS (L) in the inside

of the mast and 1 BOLT (K), 1 SPRING WASHER (M) and 1 ARC WASHER (N) in the rear of the mast as shown.

Repeat on other side.

NOTE: Only the pulse cable will need to be routed through the cable hole on the left handlebar.

NOTE: Carefully align holes

when assembling handlebars to console mast, making sure to not press down on handlebars.

NOTE: Do not completely tighten any screws or bolts until step 6 is complete!

HARDWARE BAG 2 CONTENTS :

LOCK LATCH PIN (G) Qty: 1

WAVY WASHER (F) 29 mm Qty: 1

BOLT (D) Qty: 1

FLAT WASHER (E) 27 mm Qty: 1

BOLT (I) Qty: 1

TEFLON WASHER (J) Qty: 1

RIGHT CONSOLE MAST

LEAD WIRE

CONSOLE CABLE

LOCK LATCH PIN (G)

ELEVATION FRAME

BOLT (D)

FLAT WASHER (E)

WAVY WASHER (F)

T901_Rev.2.0.indd 10-11 9/10/08 11:15:33 AM

+ 11 hidden pages