Horizon Fitness e1100GS Owner's Manual

e1100GS

ELLIPTICAL OWNER’S MANUAL

Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.

2

3

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to
the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your elliptical’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.

ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.

SERIAL NUMBER:

MODEL NAME: HORIZON e1100GS ELLIPTICAL

WARNING

4

PIVOT IN G F OOT PA DS

CR AN K

TOP CA P

GUID E R A IL SE T

SPEA KER S

WATE R B OT TL E H OLDER

UPPE R H AN DLE BA R

PULS E G RIP S

CONSOLE

RE AR COVER

STABILIZE R TUBE

POWE R C ORD SO CK ET

MAIN FR AME

PE DAL A RM

IPOD /MP 3 P LAYER P OC KET

CONSOLE FA N

CONSOLE M AS T

TOU CH PA D PANEL AN D DI SP LAY WIN DO WS

LOW ER H AN DLE BA R

LOW ER LIN K A RM

5

TOOLS INCLUDED:

F Screwdriver
F 8 mm L-Wrench
F 6 mm L-Wrench
F 5 mm L-Wrench
F 13/15 mm Flat Wrench

PARTS INCLUDED:

F 1 Main Frame
F 1 Stabilizer Tube
F 1 Guide Rail Set
F 2 Pedal Arms
F 2 Lower Handlebars
F 2 Upper Handlebars
F 2 Lower Link Arms With Footpads
F 1 Top Cap
F 1 Top Cap Rear Cover
F 1 Console Mast
F 1 Console Mast Boot
F 1 Console
F 2 Handlebar Caps
F 1 Water Bottle Holder
F 1 Audio Adapter Cable
F 1 Power Cord
F 7 Hardware Bags

UNPACKING

Unpack the product where you will be using it. Place the elliptical carton on a level flat
surface. It is recommended that you place a protective covering on your floor. Never
open box when it is on its side.

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.

If you have questions or if

there are any missing parts,

contact Customer Tech

Support. Contact information

is located on the back panel

of this manual.

NEED HELP?

PRE ASSEMBLY

6

ASSEMBLY STEP 1

A Open hardware bag 1.

B Attach the stabilizer tube to the main

frame using 4 bolts (a), 4 spring
washers (b) and 4 arc washers (c).

BOLT (A)
30 mm
Qty: 4

SPRIN G WASHER (B)
15 mm
Qty: 4

ARC WASHER (C)
17 mm
Qty: 4

HARDWARE BAG 1 CONTENTS :

BOLTS (A)

SPRING WASH ERS (B)

ARC WASHERS (C)

STABILIZER TUB E

MAIN FRAME

7

ASSEMBLY STEP 2

A Open hardware bag 2.

B Align guide rail set with main frame as

shown.

C Attach the guide rail set to the main frame

using 4 bolts (d), 4 flat washers (e) and 4
tooth washers (g).

HARDWARE BAG 2 CONTENTS :

TOOTH WASHERS (G)

FLAT WASHERS (E)

GUI DE RAIL S ET

BOLTS (D)

MAIN FRAME

TOOTH WASHER (G)
15 mm
Qty: 4

FLAT WASHER (E)
17 mm
Qty: 4

BOLT (D)
55 mm
Qty: 4

8

ASSEMBLY STEP 3

BOLT (M)

SPRING WASH ER (B)

FLAT WASHER (K)

WAVY WASHER (L)

PEDAL ARM

CRANK

PEDAL ARM WHEE L

GUID E RAIL

CONSOLE MAST

PRE-INSTALLED BOLTS

CONSOLE CABLE

MAIN FRAME

NOTE: Be
careful not
to pinch any
wires while
attaching the
console mast.

A Open hardware bag 3.

B Carefully pull the console cable through

the console mast using the twist tie located
inside the console mast.

C Gently slide the console mast onto the

main frame and attach console mast to
main frame using pre-installed bolts.

D Slide wavy washer (l) over crank

followed by pedal arm as shown. Rest
pedal arm wheel on guide rail.

E Attach the pedal arm to the crank using 1

flat washer (k), 1 spring washer (b)
and 1 bolt (m).

F Repeat steps E–F on the opposite side of the

elliptical.

BOLT (M)
20 mm
Qty: 2

SPRING WASHE R (B)
15 mm
Qty: 2

FLAT WASHER (K)
20 mm
Qty: 2

WAVY WASHER (L)

22.5 mm
Qty: 2

HARDWARE BAG 3 CONTENTS :