Horizon Fitness Delos, Delos Pro Owner's Manual
ELLIPTICAL OWNER’S MANUAL
Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.
Delos ProDelos
2 3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to
the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your elliptical’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SE RIAL NUMBE R AND MODEL NAME IN TH E BOXES BELOW:
SERIAL N UMBER:
MODEL NAM E: Horizon elliptical
WarninG
4 5
Delos
Delos Pro
Delos
Delos Pro
UnpacKinG
Unpack the product where you will be using it. Place the elliptical carton on a level flat
surface. It is recommended that you place a protective covering on your floor. Never
open box when it is on its side.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
If you have questions or if
there are any missing parts,
contact your local dealer.
neeD Help?
pre ASSEMBLY
Main partS inclUDeD:
1 main frame
2 handlebar and pedal sets
1 console mast set
1 console box
1 main parts box:
(Handle axle, Front and rear stabilizers)
partS pacKinG inclUDe D:
1 hardware paperboard
1 plastic parts bag
1 Owners manual
1 Power Cord
UPPER HANDLE BAR
PULSE GRI PS
PEDAL ARM
( DELOS PRO )
FOOTPAD
CONSOLE
UPPER HANDLE BAR COVER
LOWER HANDLEBAR
CRANK COVER
POWER CORD
SOCKET
6 7
DeloS & DeloS pro proDUc t Spare part liSt
Delos
Delos Pro
Delos
Delos Pro
SCREW (4)
Φ4 x Φ15
Qty: 8 PCS
(Delos Pro Only)
SCREW (23)
M8*55
Qty: 2 PCS
FLAT WASHER (5)
Φ8 x Φ16 x T1.5
Qty: 12 PCS
ARC WASHER (27)
Φ8 x Φ22 x T1.5
Qty: 8 PCS
SPRIN G WASHER (6)
Φ8
QTY: 10 PCS
SPRIN G WASHER (32)
Φ6
QTY: 4 PCS
SCREW (39)
Φ5 x 15
QTY: 8 PCS
L-WRENCH
8 mm
L-WRENCH WITH
SCREWDR IVER
8 mm
MULTI-USE
FLAT WRENCH
SCREW (45)
Φ4 x 20
QTY: 2 PCS
BOLT (88)
M8 x 20
QTY: 2 PCS
NUT (96)
M8
QTY: 2 PCS
screw (49)
M5 x 12
Qty: 4 PCS
PEDAL TUBE (9 8)
QTY: 4 PCS
WAVY WASHER (109)
Φ16 x Φ30 x T0.6
QTY: 2 PCS
PEDAL ADJUSTING K NOB (33)
QTY: 4 PCS
PEDAL WASHER (29)
QTY: 4 PCS
BOLT (12)
M8*15
QTY: 18 PCS
BOLT (30)
M6*52
QTY: 4 PCS
FLAT WASHER (16)
Φ8.5*Φ32*T2.0
QTY: 2 PCS
FLAT WASHER (31)
Φ6.5*Φ13*T1.5
QTY: 4 PCS
8 9
WASHER (5)
Φ8 x Φ16 x T1.5
QTy: 4
BOLT (12)
M8 x 15
QTy: 4
A Attach the REAR STABILIzER TUBE(8) to the
MAIN FRAME(1) using 4 BOLTS (12), and 4
WASHERS (5).
1
12
5
8
ASSEMBLY Step 1 ASSEMBLY Step 2
Delos
Delos Pro
Delos
Delos Pro
A Attach the FRONT STABILIzER TUBE(2) to the
MAIN FRAME(1) using 4 BOLTS (12), and 4
WASHERS (5).
WASHER (5)
Φ8 x Φ16 x T1.5
QTy: 4
BOLTT (12)
M8 x 15
QTy: 4
HarDWare partS: HarDWare partS:
1
2
12
5
10 11
ASSEMBLY Step 3 ASSEMBLY Step 4
Delos
Delos Pro
HarDWare partS: HarDWare partS:
Delos
Delos Pro
15
13
14
27
12
1
6
15
20
16
17
16
12
12
109
109
6
6
18
A Slide HANDLE AxLE (17) to the console mast
carefully and slide 2 WAVy WASHERS (109).
B Slide upper handlebar to the console mast and attach
using 2 BOLTS(12), 2 SPRING WASHE RS (6) and
2 FLAT WASHERS (16).
WAVy WASHER (109)
Φ16 x Φ30 x T0.3
QTy: 2
FLAT WASHERSCREW (16)
Φ8.5 x Φ32 x T2.0
QTy: 2
SPRING WASHE R (6)
Φ8
QTy: 2
BOLT (12)
M8 x 15
QTy: 2
A Carefully connect the upper and lower CONSOLE
CABLE (13&14) inside the console mast.
B Gently slide the CONSOLE MAST(15) onto
the MAIN FRAME (1) and attach console mast
to main frame using 4 BOLTS(12), 4 SPRING
WASHERS (6) and 4 ARC WAS HERS (27).
(Note : Be careful not to pinch any wires while
attaching)
SPRING WASHE R (6)
Φ8
QTy: 4
BOLT (12)
M8 x 15
QTy: 4
ARC WASHER (27)
Φ8 x Φ22 x T1.5
QTy: 4
12 13
A Insert LOWER HANDLEBAR COVER (50) to the
LOWER HANDLEBAR (26) on both sides
B Connect UPPER and LOWER HANDLE BAR
(20&26) with 2 BOLTS (12), 2 SPRING WASHE RS
(6) and 2 ARC WASHERS (27).
C Repeat steps A & B to connect parts 18 to 26.
SPRING WASHE R (6)
Φ8
QTy: 4
ARC WASHER (27)
Φ8 x Φ22 x T1.5
QTy: 4
BOLT (12)
M8 x 15
QTy: 4
ASSEMBLY Step 5 ASSEMBLY Step 6
Delos
Delos Pro
HarDWare partS: HarDWare partS:
Delos
Delos Pro
50
50
20
26
26
27
12
6
18
56
5
5
21
24
23
98
98
96
A Connect right PEDAL ARM (24) to CRANK (5 6)
using preassemble parts: 1 SCREWS(23), 2
WASHERS (5), 2 S LEEVES (98) and 1 NUT (96).
B Repeat above steps on the opposite side of the
elliptical.
WASHER (5)
Φ8 x Φ16 x T1.5
QTy: 4
NUT (96)
M8
QTy: 2
SCREW (23)
M8 x 55
QTy: 2
SLEEVE (98)
QTy: 4
Loading...