Assembling your cleaner
5
1 Stand ZOOM on the floor and push the handle firmly into the top of the
cleaner making sure it clicks into place.
2 Place the dust container onto the ribbed moulding and push into main body until
it clicks into place.
3 Push hose into the two hose clips.
www.hoover.co.uk
Using your cleaner
FLOOR CLEANING
Make sure handle is fully clicked into place.
1 Self adjusting head
Is ideal to clean carpeted areas.
2 Release power cord
Rotate the quick release cord storage hook to release the cord.
Plug the cleaner into a power socket.
3 Power cord location
For safe operation always ensure cord is located into the 2 cord retaining clips.
4 Working mode
Place foot on cleaner base and pull the handle back to put the cleaner in working mode.
5 Switching your cleaner on
Press the on/off switch as shown.
6
STAIR CLEANING
REMEMBER – Always work with the cleaner below you. The exceptional suction may
cause the cleaning tool to become locked to a surface, restricting airflow. In such cases,
simply lift the tool away from the surface. Make sure the handle is fully clicked into place
after use.
6 Stair cleaning mode
To use the cleaning tools, press the stair cleaning release button and lift the handle from
the cleaner body.
Release the flexible hose from clips.
The flexible hose fitted with the extended Zoom Cleaning Tool with integrated crevice tool
will reach up a full flight of 13 stairs.
7 Positioning the cleaner for maximum safety
Your cleaner incorporates an Anti-Tip Design. Ensure the cleaner is positioned up against
the bottom step.
www.hoover.co.ukwww.hoover.co.uk
1
2
3
4
5
6
7
Maintaining performance
Using your cleaner
EMPTYING THE DUST CONTAINER
For peak performance we recommend the dust container is emptied on a regular basis.
Filling must not exceed the maximum level indicated on the dust level viewing window.
REMEMBER – Always switch off and unplug the machine from the electricity supply
before maintaining your cleaner.
12 Dust container release
Holding the pre-motor filter cover, press the dust container release button and lift the dust
container from the cleaner.
13 Dust container emptying
The 2-stage opening system minimises the escape of dust when emptying. To release fine dust
first, firmly hold the dust container and push down the hand grip at the back of the container
with your palm (13a).
Rotate hand grip with your fingers to open fully the dust container and release the remaining
debris (13b). Reverse operation to close the dust container.
7
USING THE CLEANING TOOLS
8 Tools mode
Press the stair cleaning release button and lift the handle from the cleaner body.
There are 3 cleaning tools included:
9 Zoom Cleaning Tool with integrated crevice tool
The Zoom Cleaning Tool can be extended for extra reach by pushing the collar
and the handle away from each other. To retract the Zoom Cleaning Tool pull
the collar towards the handle.
10 Furniture nozzle
The furniture nozzle is stored on the cleaner body and fits on the crevice tool.
It is ideal for upholstery, stair cleaning and many other uses.
11 Dusting brush
The dusting brush is stored on the cleaner body and fits on the crevice tool.
It is ideal for gentle dusting on all surfaces.
REMEMBER - Make sure handle is fully clicked into place after use.
11
www.hoover.co.uk
8
9a
9b
10
12
13a
13b
Maintaining performance
FILTER SYSTEM
There are 3 filters and a vortex tube. The HEPA and foam pre-motor filters and vortex tube
are located beneath the dust container lid (14a). The exhaust filter is located below the dust
container (16b).
REMEMBER – Always switch off and unplug the machine from the electricity supply before
maintaining your cleaner.
14 Cleaning the pre-motor filters
For optimum performance clean the HEPA pre-motor and foam pre-motor filter after each
dust container empty.
(14a) Rotate the pre-motor filters cover anticlockwise.
(14b) The HEPA and foam pre-motor filters and the vortex tube are attached to the lid.
(14c) Remove the vortex tube.
(14d) Remove the foam filter.
(14e) Tap the HEPA pre-motor filter against an hard surface and shake the foam filter to
remove dust.
15 Washing the pre-motor filters
For optimum performance wash the pre-motor filters after 5 dust container empties.
(15a) Wash the HEPA and foam pre-motor filters under hand warm water.
If preferred, remove the HEPA filter from the lid prior washing (15b).
Do not scrub and do not use detergents. Allow to air dry thoroughly before refitting.
Reassemble the components by reversing the above process.
16 Exhaust filter maintenance
The exhaust filter requires little or no maintenance and should only need checking if there is a
drop in performance.
To access the exhaust filter, remove the dust container from the cleaner (16a). Press the filter
release button to release the exhaust filter (16b and 16c). Do not scrub and do not use
detergents. Allow to air dry thoroughly before refitting.
REMEMBER – To maintain optimum cleaning performance it is imperative to wash the HEPA
pre-motor filter and foam pre-motor filter every 5 dust container empties.
8
www.hoover.co.ukwww.hoover.co.uk
14a
14b
14c
14d
14e
15a
15b
16b
16a
16c
Maintaining performance
9
CLEARING BLOCKAGES
REMEMBER – Always switch off and unplug the machine from the electricity supply before
maintaining your cleaner.
17 Clearing a blockage in the flexible hose
Twist the hose end connectors to remove hose from both the base of the cleaner and the
handle.
Check hose and handle for blockages. Use a blunt rod to remove any obstruction.
After clearing any blockage in the hose, refit both hose connectors ensuring the hose
supports are located on the inner side of the hose.
18 Clearing a blockage at the cleaner base
Remove the flexible hose as previously described. Unclip the cover at the base of the machine
(18a). Check the lower hose for any blockages (18b). The lower hose can be easily removed for
inspection. Refit hose and hose cover.
www.hoover.co.uk
17
18a
18b
Maintaining performance
19 CHECKING BELT AND BRUSHES/ REPLACING THE BELT
REMEMBER – Always switch off and unplug the machine from the electricity supply before
checking the brushes, belt or removing the hood.
Remove the flexible hose from the cleaner – twist hose end connectors to remove hose
at both ends as shown in section 17.
Lie cleaner flat. Using a crosshead screwdriver remove 4 hood screws as shown (19a).
Turn cleaner over and lift off hood (19b).
Remove agitator brush and belt assembly by pulling upwards out of the cleaner
base (19c).
Replace belt, if worn or broken, by looping the new belt over the metal
motor spindle (19d).
Refit agitator brush assembly by holding the brush and stretching the belt.
Align and insert both agitator end caps into slots in the base as shown (19e).
When located, rotate the agitator brush to ensure free movement of the belt.
Push down front of hood to fit in the cleaner base (19f).
Lie cleaner flat and secure hood using the 4 screws (19a).
Refit flexible hose.
10
i)
ii)
iii)
iv)
v)
vi)
vii)
viii)
ix)
x)
www.hoover.co.ukwww.hoover.co.uk
19a
19b
19c
19d
19e
19f
Before calling Hoover
11
User checklist
If your cleaner has stopped working completely, run through the following check list:
NOTE: It will take about 30 minutes for the thermal cut out to automatically reset.
If your cleaner is not working properly, run through the following checklist:
REMEMBER – Always switch off and unplug the machine from the electricity supply before
maintaining your cleaner.
REMEMBER - If there is any doubt, call the Hoover Advice Helpline (open 7 days a week)
on 08705 400600. They may be able to assist you over the telephone.
Is there a working electricity supply to the cleaner?
Check with another electrical product.
A thermal cut out switches off the cleaner automatically to prevent overheating if the
cleaner is used when the dust container is over full, or the filters require cleaning,
or there is a blockage. If this should happen switch off and unplug the machine from
the electricity supply. To correct the fault please refer to sections 12-18.
i)
ii)
Is the dust container overfilled? (refer to sections 12 and 13)
Is the hose blocked? (refer to section 17)
Is there a blockage in the cleaner base? (refer to section 18)
Are the filters blocked? (refer to sections 14, 15 and 16)
Are the brushes rotating? (refer to section 19)
i)
ii)
iii)
iv)
v)
www.hoover.co.uk
Important information
12
www.hoover.co.uk
Genuine Hoover Spares
Always replace parts with Genuine Hoover Spares. These are available from your local
Hoover dealer or direct from Hoover. When ordering parts, always quote your model
number.
Hoover Service
Should you require service at any time, please call your local Hoover Service Office. Hoover
have a computerised nationwide service network of over 500 engineers who will respond
quickly to your call and guarantee your repair for 12 months.
Safety and the Environment
As the owner of a new Hoover product, we would like to tell you more about the high
standards we have set in safety and the environment.
Safety
Although safety certification of electrical appliances is not required by law in the UK,
Hoover believe that independent approval is the best way of demonstrating safety in design
and manufacture. The British Electrotechnical Approvals Board (BEAB), the independent UK
national authority for the safety of domestic electrical appliances, ensure that European
Safety Standards are met and maintained throughout the production life of an appliance.
All appliances which pass these tests are permitted to carry the BEAB mark of safety.
The Environment - WEEE Directive
This appliance is marked according to the European directive 2002/96/EC on
the Waste of Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this
product.
The symbol on the product indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for waste
disposal.
For more detailed information about treatment, recovery and recycling of this product, please
contact your local city office, your household waste disposal service or the shop where you
purchased the product.
Notes
13
www.hoover.co.uk
Loading...