HOOVER UDT518SAFP Dimension Guide

Undercounter Dishwasher
PRODUCT MODEL NUMBERS
UDT518SAFP
Location Requirements
There must be a minimum of 255/8" (65.1 cm) in front of dishwasher to allow door to open fully.
Countertop
Dishwasher
255/8"
(65.1 cm)
2" (5.1 cm) min.
clearance for door
opening
Electrical Requirements
■ 120 volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical supply
■ Wiring must be 2-wire with ground
We recommend:
■ A time-delay fuse or circuit breaker
■ A separate circuit
Water Supply Requirements
■ A hot water line with 20-120 psi (138-862 kPa) water pressure.
■ 120°F (49°C) water at dishwasher.
3
/8" O.D. copper tubing with compression fitting or flexible stainless steel braided fill line (1/2" minimum plastic tubing is not recommended).
■ A 90° elbow with
3
/8" N.P.T. external pipe threads on one end.
Do not solder within 6" (15.2 cm) from water inlet valve.
Product Dimensions
22" (59 cm)*
321/2" (82.6 cm) min.
35" (88.9 cm) max.
18"
(45.7 cm)
*To front of door frame
SIDE VIEW
171/2" (44.5 cm min.
18"(45.7 cm) max.
21/2"
(6.2 cm)
Drain Requirements
■ Use the new drain hose supplied with your dishwasher. If this is
not long enough, use a new drain hose with a maximum length of 10 ft (3.05 m) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, use 5/8" (1.58 cm) or 7/8" (2.2 cm) inside diameter hose and a coupler to connect the two hose ends. Secure the connection with 2 clamps.
■ Connect drain hose to waste tee or disposer inlet above drain
trap in house plumbing and 32" (81.3 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.
■ Use an air gap if the drain hose is connected to house
plumbing lower than 18" (45.7 cm) above floor.
Air gap
Use 1/2" minimum I.D. drain line fittings.
■ Do not connect drain lines from other devices to the
dishwasher drain hose.
REAR VIEW
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
Page 1 of 2
W10702387-D-WH
5/16
Cabinet Cutout Dimensions
All surfaces must be free from instrusions
4"
(10.2 cm)
175/8" (44.8 cm) min.
18" (45.7 cm) max.
* Underside of countertop to floor
323/4" to 341/2"*
(83 cm to 88 cm)
24"
(61 cm)
min.
6"
(15.2 cm)
Cut holes in shaded area of cabinet walls or floor for plumbing and electrical service.
NOTE: ADA installation, 321/2" (82.5 cm) beneath 34" (86.4 cm) high countertops may be accomplished by adjusting the toekick and leveling legs.
Custom Panel Dimensions and Installation
Custom panel should be constructed according to diagram below.
15.35" (39.0 cm)+
12-φ 0.08" (0.2 cm)+
Hole deep 0.39" (0.10 cm)
2.56" (6.5 cm)+
6.79" (17.25 cm)+
17.64" (44.9 cm)+
16.48" (41.8 cm)+
7.05" (17.9 cm)+
6.89" (17.5 cm)+
0.59" (1.5 cm)+
26.77" (68.0 cm)+
1.50" (3.8 cm)+
1.18" (3.0 cm)
17.4" + (44.4 cm)
Install the hook on the custom wood panel and insert the hook into the slot on the outer door of the dishwasher. After positioning the panel, attach the panel to the outer door with screws and bolts.
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
Page 2 of 2
W10702387-D-WH
5/16
Loading...