Hoover U5758-900, U5757-900, U5755-900, U5750-900, U5721-900 Owner’s Manual

...
m
TM
by HOOVER
Congratulations
your purchase!
www.hoover.com
This product was designed for easy assembly (see page 3)
Review this manual before
ENGLISH -_ pp.1-14
operating cleaner
ESPANOL -_ pag. 16-23 FRANGAIS -_ p. 24-31
Fill in and retain
The model and serial number are located on the bottom of the cleaner.
For your personal records, please enter the COMPLETE model and serial number in the spaces provided and retain this information.
Your cleaner is model
and has serial number It is suggested that you attach your sales receipt to this owner's manual.
Verification of date of purchase may be required for warranty service of your
HOOVER product.
|mportant Safegua
When using an electrical appliance, always follow
|ndex
Assembling Cleaner .......................... 3-4
Carton Contents .................................... 3
Cleaner Descriptions ............................ 5
How To Use ........................................ 5-7
Cleaning Tools .................................. 7
If You Have a Problem .................. 13=14
Clearing Blockages ........................ 14
important Safeguards .......................... 2
Lubrication .......................................... 13
Maintenance
Authorized Service .......................... 13
Cleaning filters .............................. 8-9
Emptying Dirt Cup ............................ 8
Replacing Agitator Brush Roll ...... 11
Replacing Power Hand Tool
Agitator Brush Roll ...................... 12
Replacing Belt ............................ 10-11
Replacing Power Hand Tool Belt ..12
Replacing Edge Groomers ............ 11
Replacing Headlight ........................ 10
Thermal Protector .............................. 13
Warranty .............................................. 14
®@
© 2000 The Hoover Company
www, hoover, com
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
am=rig-[]To reduce the risk of fire, electric shock, or injury:
Do not use outdoors or on wet surfaces.
Close supervision is necessary when any appliance is used by or near children.
Do not allow vacuum cleaner to be used as a toy or to run unattended at any time. Keep hair, loose clothing, fingers, feet and all parts of body away from openings,
rotating agitator and other moving parts. Do not operate cleaner in bare feet or when wearing open toe shoes or sandals.
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Do not use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present.
Avoid picking up hard, sharp objects with the cleaner. They may damage the cleaner,
Always turn off this appliance before connecting or disconnecting hose.
Do not use without dirt cup or filters in place. Empty cup and clean filter frequently
when picking up very fine materials such as powder. Use extra care when cleaning on stairs. Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, or anything that may reduce air flow.
Do not pul! or carry by cord, use cord as a handle, close door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
Always disconnect cord from electrical outlet before servicing the cleaner. Unplug cleaner when not in use. Turn off all controls before unplugging. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Never
handle plug or appliance with wet hands. The use of an extension cord is not recommended.
Do not use with damaged cord or plug. if appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover
Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot). Use vacuum cleaner only for its intended use as described in the instructions.
Use only attachments recommended by The Hoover Company; others may cause hazards.
Save
basic precautions, including the following:
m
m
ructio.s!
This cleaner was inspected and packaged carefully before being shipped from the factory. If you should happen to need assistance during assembly or operation, call:
1-800-944-9200 for an automated referral of service outlet locations (U.S. only) OR
1-330-499-9499 to speak with a representative in our Consumer Response Center OR
Visit us on-line at www.hoover.com to find the service outlet nearest you (click on the "Service" button).
Carton contents
uu
C
A B
Remove all parts from carton and identify each item shown.
Make sure all parts are located before disposing of packing.
A. Handle section
B. Cleaner body C. Hose, cleaning tools and wands
(packed on cleaner) D. Powered hand tool (some models)
Note: The white switch lock above the ON/OFF switch aids in the assembly of your cleaner, Assembly can be continued if
the switch lock is missing, However, do not remove the switch lock until assembly is completed.
Continued -_ 3
STEP 1 Attach handle
\\
Remove cardboard (A) and screws from handle section. Discard card-
board.
Slide handle section onto back of handle.
Push screws into holes on back of handle.
Tighten screws securely with a Phillips screwdriver.
Remove powered hand tool (some models) from plastic bag and return it to the tool storage area.
Open tool cover on cleaner body (B).
Remove powered hand tool (some models).
Remove switch lock (C) above ON/ OFF switch (D) by pulling it straight
out. Dispose of switch lock.
If switch lock has come off during assembly, make sure switch is in OFF position (down) before plug- ging into electrical outlet.
Make sure that the switch is in the OFF position.
Cleaner description
The assembled cleaner will look like the drawing. Model with Powered Hand Tool is shown.
1. Handle
2. ON/OFF switch
3. Tool cover
4. Dusting brush
5. Powered hand tool* or Crevice tool*
(depending on model)
6. Furniture nozzle
7. Dirt cup latch
19
8. Dirt cup lid
9. Dirt cup
10. Dirt cup handle
11. HEPA cartridge filter
12. Pre-filter
13. Final filter
14. Three position handle
release pedal: step on
lever to lower handle to operating or low positions.
15. Nozzle control knob:
slide knob to correct set- ting for height of carpet
being cleaned.
16. Furniture guard
17. Headlight
18. Edge groomers
19. Hose
20. Hose rack
21. Cord hooks: wrap cord around hooks for
storage. The top hook can be rotated right or left for easy cord
release.
22. Carrying handle
23. Extension wands
24. Crevice wand*: stores
in rear wand.
*Some models only
Operate cleaner only at voltage specified on data
plate on bottom of
cleaner. This cleaner is intended
for household use.
Polarized plug
Toreduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the proper outlet. Do not change the plug in
any way.
Transporting cleaner
To move your cleaner from room to room, put handle in upright position, tilt cleaner back on rear wheels and push
forward.
ON-OFF switch
Plug cord into electrical outlet. To turn cleaner ON, push switch up. To turn cleaner OFF,push switch down.
p_,€]
Carrying cleaner
The cleaner can also be moved by
using the carrying handle.
Handle positions
The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating posi- tion for general operation on carpet and floors; low for reaching under low furniture. Step on handle release lever
to lower handle.
Continued -_ 5
C
P_4
i._ _ D
IIIIIliil l......
B
Carpet height adjustment
The cleaning of carpet and rugs takes place at the nozzle (A).
When it is necessary to raise and lower the nozzle for various carpet pile heights, slide
the nozzle control knob (B) to the desired setting.
.z: ......
Handle position
For ease in sliding knob, the handle should be in the upright position (C).
The nozzle will not move into the
adjusted position until the cleaner
handle is lowered to the operating position (D).
Settings
For maximum cleaning performance,
the following carpet height settings are
recommended.
Lowest setting: for bare floors and all types of carpet
Note: If the cleaner is difficult to push, slide knob to the next higher setting.
Higher settings: for very deep pile carpet where easier pushing effort is
desired, while maintaining good cleaning performance.
Cleaning lightweight flexible rugs
Stand on one end of rug and move cleaner toward other end or edge.
Before reaching edge, push down on
handle. This will lift up the nozzle (front of cleaner) and will prevent rug from clinging to cleaner. Continue to lift up
nozzle so that when you have reached the edge, it is completely off the rug.
Move cleaner back to start again, lower
nozzle, and use only forward strokes.
Edge cleaning
Special edge groomers are provided on both sides of the nozzle to remove dirt in
carpet near baseboards and furniture. Guide either side of nozzle parallel to
edge of carpet or furniture.
Stair cleaning
Use the hose and powered hand tool* or furniture nozzle for stair cleaning. Clean from bottom to top.
When using cleaning tools, the
agitator will continue to rotate. CAUTION: To avoid personal injury or
unnecessary wear to carpet, and to prevent the cleaner from falling, always place it at bottom of stairs.
*some models only
How to attach tool
cover
The tool cover is designed with a "break-
away" feature which allows it to snap free if
it is pushed open too far.
Toreattach, align hinges of cover with slots
on sides of tool storage area.
Push cover down to secure in place.
Cleaning tools
Tools allow for cleaning surfaces above the floor and for reaching hard to clean
areas.
Handle must be in the upright posi-
tion for tool use.
CAUTION: Agitator continues to rotate
while cleaner handle is in upright
position. Avoid tipping cleaner or
setting it on furniture, fringed area
rugs or carpeted stairs during tool
use,
F
E
Attach wand and tools
Attach tool or wand to the hose (E). Attach second wand or tool to wand (F)
by pushing it firmly onto the wand. Twist wand or tool slightly to tighten or
loosen the connection.
How to clean tools
To clean the hose and the powered hand tool, wipe off dirt with a cloth dampened in a mild detergent. Rinse with a damp cloth. Do not submerge powered hand tool in water.
Cleaning tools may be washed in warm water with a detergent. Rinse and air dry before using.
J | J
K
( )) ( ))
Select proper tool
G. Dusting brush may be used for
carved furniture, table tops, books,
lamps, lighting fixtures, venetian blinds,
baseboards, shutters, and registers.
H. Furniture nozzle may be used for
upholstered furniture, draperies, mat-
tresses, clothing, automobile interiors,
and carpeted stairs.
I. Powered hand tool* may be used for upholstered furniture, carpeted stairs and hard-to-reach places.
J. Crevice tool* may be used in tight spaces, corners and along edges in such places as dresser drawers, uphol- stered furniture, stairs and baseboards.
K. Crevice wand* can be used in tight
L
spaces, corners and along edges in such places as dresser drawers, uphol- stered furniture, stairs, and baseboards.
It can also be used for extra reach with the dusting brush and/or extension
wand. L. Wands are used to give extra length
to your hose. Use them with any of the above tools.
Extra reach hose*
Push ON/OFF switch to OFF position. Remove regular hose from cleaner. Align end of extra reach hose with projections (M) over slots (N) in dirt duct.
*some models
Slide hose into (N) and twist hose to lock
it into place. (To detach hose, reverse
procedure.) Attach wands or tools to the other end of hose.
*Available at additional cost if not includ- ed with your cleaner. 7
Familiarizeyourselfwiththesehome maintenancetasksasproperuseand
careofyourcleanerwillensurecontin- uedcleaningeffectiveness.
Dirt cup
The dirt cup assembly consists of the following parts:
Lid (A)
Dirt Cup (B)
Pre-filter (C)
HEPA Cartridge Filter (D)
Dirt Inlet Opening (E) While the cleaner is in operation, the pre-
filter screen will stop larger debris from
entering the HEPA cartridge filter chamber. This larger debris will be seen collecting in the left side of the dirt cup. The HEPA car- tridge filter will collect fine particles that
have passed through the pre-filter screen.
When to empty
Itis recommended that the dirt cup be
emptied before the dirt reaches the dirt inlet opening on back of dirt cup (Fig. 3-1)
or after every use if preferred.
CAUTION: Very fine materials, such as face powder, cornstarch or fire- place soot, may seal the filter and cause loss of suction. When using the cleaner for this type of dust, empty the cup and clean the filters
often.
How to empty
Disconnect cleaner from electrical outlet. Do not use cleaner without dirt
cup or filters in place.
Push latch (F) to the left to unlock. Lift cup slightly and pull straight out to
remove from cleaner.
Remove lid. Note: It is not necessary to remove the
HEPA cartridge filter to empty the dirt
cup. Tap side of cup until no more dust
particles fall from the HEPA cartridge
filter.
G
Replace dirt cup lid.
Slide cup straight into cleaner cavity.
Bottom of cup will rest behind grooves
at bottom of cleaner cavity (G).
Push latch (F) to the right to lock in
place.
Filter assembly
The HEPA cartridge filter and pre-filter are essentially self-shedding.
Tapping the side of the dirt cup as described in "How to empty dirt cup" should sufficiently remove dust and fine particles from the HEPA cartridge filter and pre-filter.
The filter assembly can also be removed for additional cleaning.
B5.1
How to clean filter assembly
Remove dirt cup and dirt cup lid as described in "How to empty dirt cup."
Grasp pre-filter frame and pull up firmly. Slide filter assembly out of cup.
GraspendofHEPAcartridgefilterand pullitawayfrompre-filter.Remove
cartridgefromassembly. Thepre-filter(O)canbecleanedwitha
brushandthenrinsedwithwater.Allow pre-filtertodrythoroughly.
!
i
i
i i
It is recommended that the HEPA cartridge filter be cleaned by tapping
either of the ends. DO NOT tap soft
pleated sides of HEPA cartridge filter as this could damage the filter.
Tap filter until no more dust particles fall from the filter.
E_5[i]
To re-assemble filter assembly, place
large knob of HEPA cartridge filter in hole on bottom of pre-filter.
Snap top of HEPA cartridge filter into
place.
Secondary and final filters
Align grooves (H) on pre-filter frame with
grooves (I)in dirt cup.
Slide filter assembly down into cup until a light snap is felt. Gently pull up on
assembly to ensure that it is seated properly in the cup. Ensure that no part of pre-filter screen extends above top
edge of dirt cup.
Replace lid and return cup to cleaner
(Fig. 3-4).
Let filter air dry and reposition it on the
side of cleaner. Make sure the white side of the filter faces outward. Close door.
Should you want to replace this filter, ask for HOOVER part No. 40110006.
Do not operate cleaner without any of
the filters in place,
Cleaning secondary filter
Disconnect cleaner from electrical
outlet.
The secondary filter (J), located behind the grill in the bottom of cleaner cavity,
protects the motor from dirt particles.
If the filter becomes dirty, remove dirt cup (Fig. 3-2). Remove screw and pull grill out. Lift out filter.
Hand wash filter in cold water with mild detergent, then air dry.
Reposition dry filter, grill and screw.
Replace dirt cup. Should you want to replace this filter, ask
for HOOVER part No. 38762008.
Cleaning final filter
The final filter assists in the filtration
process to return clean air to the room.
To remove this filter when it becomes
dirty, open the door on the side of the cleaner.
Lift out filter (K) and hand wash it in cold
water with mild detergent.
Reattaching filter door
Tile filter door is designed with a "break- away" feature which allows it to snap free if it is pushed open too far.
To reattach, align hinges (L) of cover with slots on sides of filter area.
Press door back into place.
Continued ._ 9
Check agitator shield
Because your cleaner picks up so well, we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters.
Removing debris under the shield will help maintain your cleaner's excellent pick up and suction. Remove debris as
follows:
1. Disconnect cleaner from electrical outlet.
2. Check for dirt accumulation by removing bottom plate (Fig. 3-17), removing agitator (Fig. 3-18), and lifting agitator shield (Fig. 3-20).
3. Remove any debris and replace shield, agitator and bottom plate (Figs.
3-20 to 3-22).
Headlight replacement
What to buy
This cleaner uses a 12 volt, wedge base type 912 bulb, HOOVER part No.
27313101.
Removing lens
Disconnect cleaner from electrical outlet.
Using a screwdriver, remove tile two screws as shown and lift off lens.
Installing bulb
Pull old bulb straight out of socket. Push new bulb straight into socket until
locked in place
Excessive force is not required.
Belt replacement
The belt on your HOOVER cleaner causes the agitator to rotate and is
important for the effective operation of the cleaner. The belt is located under
the bottom plate of the cleaner and should be checked from time to time
to be sure it is in good condition.
When to replace
Disconnect cleaner from electrical outlet.
To check belt, remove bottom plate as shown in "How to replace." Replace
belt if it is stretched, cut or broken.
What to buy
To assure effective operation, use only genuine HOOVER belts with your
cleaner. When purchasing a new belt, ask for HOOVER part No. 38528033.
Replacing lens
Reposition lens and secure with the two
screws.
How to replace
Disconnect cleaner from electrical outlet.
Place handle in low position and turn cleaner over so bottom side is up.
Remove the 4 screws as shown with a Phillips screw driver.
Lift off bottom plate (A).
Removing belt
Remove agitator brush roll and used belt.
Discard used belt.
10
Loading...
+ 22 hidden pages