Hoover U5432900 User Manual

WindTunnel

™

by HOOVER

Congratulations on your purchase!

This WindTunnel™ vacuum cleaner takes HOOVER® Type “Y” Allergen Filtration filter bags

This product was designed for easy assembly (see page 3)

www.hoover.com

Thank you for choosing a HOOVER product

Please enter the COMPLETE model and serial numbers in the spaces provided. Model___________________________________

Serial number___________________________________ Hint: Attach your sales receipt to this owner’s manual.

Verification of date of purchase may be required for warranty service of your HOOVER product.

Be sure to fill out and return the product registration card included with your cleaner (see back cover).

Owner’s Manual

ENGLISH ➜ pp.1-13

ESPAÑOL ➜ pág. 15-22 FRANÇAIS ➜ p. 23-30

Review this manual before

operating cleaner

Important Safeguards!

When using an electrical appliance, always follow basic precautions, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

Warning:To reduce the risk of fire, electric shock, or injury:

• Do not use outdoors or on wet surfaces.

• Close supervision is necessary when any appliance is used by or near children. Do not allow vacuum cleaner to be used as a toy or to run unattended at any time.

• Keep hair, loose clothing, fingers, feet and all parts of body away from openings, rotating agitator and other moving parts. Do not operate cleaner in bare feet or when wearing open toe shoes or sandals.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Do not use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present.

• Avoid picking up hard, sharp objects with the cleaner. They may damage the cleaner and the bag.

• Always turn off this appliance before connecting or disconnecting hose.

• Do not use without dust bag or filters in place. Change bag frequently when picking up very fine materials such as powder.

• Use extra care when cleaning on stairs.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, or anything that may reduce air flow.

• Do not pull or carry by cord, use cord as a handle, close door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Always disconnect cord from electrical outlet before servicing the cleaner.

• Unplug cleaner when not in use. Turn off all controls before unplugging.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Never handle plug or appliance with wet hands.

• The use of an extension cord is not recommended.

• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot).

• Use vacuum cleaner only for its intended use as described in the instructions. Use only attachments recommended by The Hoover Company; others may cause hazards.

Save these instructions!

Contents

Assembling Cleaner..........................3-5

Carton Contents ....................................3

Cleaner Descriptions............................5

How To Use ........................................5-7

Cleaning Tools ................................7-8

If You Have a Problem........................12

Important Safeguards ..........................2

Lubrication ..........................................11

Maintenance ....................................8-11

Authorized Service ..........................12

Cleaning Filters ................................9

Clearing Blockages ........................12

Replacing Agitator Brush Roll ......11

Replacing Belt ................................10

Replacing Edge Groomers ............11

Replacing Headlight ........................10

Replacing Filter Bag ......................8-9

Thermal Protector ..............................11

Warranty ..............................................13

STEP 1 Attach rack and handle

Carton contents

Remove all parts from carton and identify each item shown. Make sure all parts are located before disposing of packing materials.

A. Handle section B. Cleaner body C. Hose rack D. Hose, cleaning tools and wands E. Handle bolts and nuts packet

(in bag with owner’s manual)

If you need any assistance:

Visit our website at www.hoover.com. Click on the “Service” button to find the service outlet nearest you OR Call 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. only) OR Call 1-330-499-9499 to speak with a representative in our Consumer Response Center.

Please do not return this product to the store.

Continued

➜

1. Cleaner assemblyNot

Open tool cover on handle section (A).

1-2

Attach hose rack to handle section by fitting hooks (B) on rack over slots (C) on handle section.

Align hole on rack with circular tab on handle.

1-4

1-3

1-1

Note: The white switch lock above the ON/OFF switch aids in the assembly of your cleaner. Assembly can be continued if the switch lock is missing. However, do not remove the switch lock until assembly is completed.

Align end of hose with projections (A) over slots (B) in dirt duct.

1-8

1-10

1-6

Place nuts in recessed areas on front of handle. Hold each nut in place while tightening each bolt securely with a Phillips screwdriver.

Reposition bag door by fitting tabs on bottom of door into opening. Press top of door to snap securely shut.

Press cord into the 3 notches and the clip as shown.

Slide hose into (B) and twist hose to lock it into place. Lift hose tube cover (C).

NOTE: Hose must be connected as shown for all

operations.

STEP II Attach hose

Remove bag door on cleaner body by pushing down at top of door and pulling door outward.

Switch (A) above bag door should be in OFF position.

While holding rack in place, slide handle onto cleaner body.

Make sure tab is inserted fully into slot.

1-7

Push bolts into holes on back of handle.

1-9 1-10

1-12

1-11

1-5

Position hose over rack and into hose tube (D) or (E) (depending on your model).

2. How to use

Cleaner description

15.Nozzle control knob:

slide knob to correct setting for height of carpet being cleaned

16. Headlight

17. Check bag indicator

18. Stair cleaning handle:

located below lower edge of door.

19. Bag door

20. Cord clip

21. Hose rack

Operate cleaner only at voltage specified on data plate on bottom of cleaner.

This cleaner is intended for household use.

1. Handle

2. ON/OFF switch

3. Cord hooks: wrap cord

around hooks for storage. The top hook can be rotated right or left for easy cord release.

4. Hose

5. Tool cover

6. Dusting brush

7. Furniture nozzle

8. Crevice tool

9. Carrying handle

10.Wands

11.Final filter door

12.Handle release lever:

step on lever to lower handle to operating or low positions

13.Edge groomers

14.Furniture guard: helps

prevent cleaner from marking furniture.

2-2

ON-OFF switch

Plug cord into electrical outlet. To turn cleaner ON, push switch up.

To turn cleaner OFF, push switch down.

STEP III Position tools

Polarized plug

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Cord clip

To help keep the cord out of the way while vacuuming, position cord in cord clip (A) located at rear of cleaner on hose rack.

1-14

1-15 1-16

2-1

The assembled cleaner will look like the drawing.

Place smaller unridged end of wand into bottom of rack. Snap wand into clip. Repeat with other wand. Open tool cover.

Insert ends of dusting brush (A), crevice tool (B) into storage areas. Secure furniture nozzle (C) in clip. Close tool cover.

Remove switch lock (A) above ON/OFF switch (B) by pulling it straight out. Dispose of switch lock.

If switch lock has come off during assembly, make sure switch is in OFF position (down) before plugging cord into electrical outlet.

2-8

Transporting cleaner

To move your cleaner from room to room, put handle in upright position, tilt cleaner back on rear wheels and push forward.

Handle positions

The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating position for general operation on carpet and floors; low for reaching under low furniture. Step on handle release lever to lower handle.

Carrying cleaner

The cleaner can also be moved by using the carrying handle.

2-3

2-4

2-6

2-5

Carpet height adjustment

The cleaning of carpet and rugs takes place at the nozzle (A).

When it is necessary to raise and lower the nozzle for various carpet pile heights, slide the nozzle control knob (B) to the desired setting.

HIGH

BARE FLOOR

2-7

Handle position

For ease in sliding knob, the handle should be in the upright position (C).

The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position (D).

Settings

For maximum cleaning performance,

the following carpet height settings are recommended:

• Lowest setting: for all types of carpet Note: If the cleaner is difficult to push,

slide knob to the next higher setting.

• Higher settings: for very deep pile carpet where easier pushing effort is desired, while maintaining good cleaning performance.

Cleaning lightweight flexible rugs

Stand on one end of rug and move cleaner toward other end or edge. Before reaching edge, push down on handle. This will lift up the nozzle (front of cleaner) as shown and will prevent rug from clinging to cleaner. Continue to lift up nozzle so that when you have reached the edge, it is completely off the rug. Move cleaner back to start again, lower nozzle, and use only forward strokes.

Cleaning tools

Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas.

The cleaner is ready for tool use when handle is in upright position.

CAUTION: Agitator continues to rotate while cleaner handle is in upright position. Avoid tipping cleaner or setting it on furniture, fringed area rugs or carpeted stairs during tool use.

2-9

2-11

Stair cleaning

A stair cleaning handle has been designed for ease in using your cleaner on stairs. With handle in operating position, place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle.

As an alternative, you may use the hose and furniture nozzle for stair cleaning. Clean from bottom to top.

When using cleaning tools, the agitator will continue to rotate.

CAUTION: To avoid personal injury or unnecessary wear to carpet, and to prevent the cleaner from falling, always place it at bottom of stairs.

Edge cleaning

Special edge groomers are provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture.

Guide either side of nozzle parallel to edge of carpet or furniture.

2-10

2-12

Continued

➜

How to attach tool cover

The tool cover is designed with a “break-away” feature which allows it to snap free if it is pushed open too far.

To reattach, align hinges of cover with slots on sides of tool storage area.

Push cover down to secure in place.

How to clean tools

To clean the hose, wipe off dirt with a cloth dampened in a mild detergent. Rinse with a damp cloth.

Cleaning tools may be washed in warm water with a detergent. Rinse and air dry before using.

2-13

Removing hose

When using cleaning tools, cleaner handle should be in the upright position. Also, turn cleaner OFF before disconnecting and connecting hose to hose tube (A).

To use hose, lift hose end as shown. Lower cover (B) onto hose tube. When you are finished cleaning with

the tools, be sure to lift cover from

hose tube and reposition hose end into tube.

Where to buy

Filter bags may be purchased from your Authorized Hoover Dealer (Depot), Leading Retailers, Hoover Factory Service Centers, or through The Hoover Company on-line at

www.hoover.com.

It is imperative that you use only genuine HOOVER filter bags made by The Hoover Company to assure that your cleaner operates at peak performance. HOOVER bags can be identified by these trademarks —

Removing bag door

What to buy

To assure cleaning effectiveness, use only Genuine HOOVER®

Allergen Filtration Type Y disposable filter bags.

Attach wand and tools

Attach tool or wand to the hose (C). Attach second wand or tool to wand

(D) by pushing it firmly onto the wand.

Twist wand or tool slightly to tighten or loosen the connection.

2-14

2-18

Check bag indicator

The indicator (K) will begin to show red as the filter bag fills with dirt.

There are three conditions that will cause the indicator to become completely red:

1. If the bag is full; change the bag.

2. If very fine materials have been picked up, clogging the bag pores; change the bag.

3. If there is a blockage in the nozzle, hose, tools or at the bag opening; remove the blockage (see “Clearing blockages” section).

Select proper tool

E. Dusting brush may be used for carved furniture, table tops, books, lamps, lighting fixtures, venetian blinds, baseboards, shutters, and registers.

F. Furniture nozzle may be used for upholstered furniture, draperies, mattresses, clothing, automobile interiors, and carpeted stairs.

G. Crevice tool may be used in tight spaces, corners and along edges in such places as dresser drawers, upholstered furniture, stairs and baseboards.

H. Wands are used to give extra length to your hose. Use them with any of the above tools.

2-15

Extra reach hose

(available at additional cost) Follow the steps below for attaching

and detaching the hose.

Push ON/OFF switch to OFF position. Remove regular hose from

cleaner. Align end of extra reach hose with projections (I) over slots (J) in dirt duct (Fig. 2-16).

Slide hose into (J) and twist hose to lock it into place (Fig. 2-17).

To detach hose, reverse procedure. Attach wands or tools to the other end of hose.

2-16

2-17

3. Maintenance

Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness.

Filter bag

When to replace

Check filter bag from time to time. It is recommended that you change the filter bag when dirt reaches the dotted line. If more dirt than this accumulates, your cleaner will not operate effectively.

Note: All new carpet has loose fibers which can fill the bag quickly while vacuuming. This type of

debris does not activate the “Check bag” indicator available on some models.

So, if you are using the cleaner on

new carpet, be sure to change the filter bag often, even if you have a

“Check bag” indicator and it does not show red.

CAUTION: Very fine materials, such as face powder, cornstarch, fireplace ashes or fireplace soot, may seal the filter bag and may cause it to burst even though it is only partially full of dirt. When cleaner is used to remove material of this nature, change filter bag often.

3-1

3-2

Replacing bag door

Reposition bag door by placing tabs on bottom of door into opening (C).

Press top of door to snap securely shut.

Removing bag door

To change filter bag, press down at top of bag door and pull door forward.

Remove door.

Removing and installing filter bag

Grasp filter bag collar (A) and pull collar from tube (B).

Note: Do not clean out old filter bag and reuse. Discard used filter bag.

Hold new filter bag as shown. Align opening in filter bag with (B).

Push (A) firmly onto (B). Tuck in filter bag.

Secondary and final filters

The secondary filter (A), located behind the grill in the bottom of bag compartment, protects the motor from dirt particles.

If filter becomes dirty, pull off grill and lift out filter.

Hand wash filter in cold water with mild detergent, then air dry.

Reposition dry filter and grill. Should you want to replace this fil-

ter, ask for HOOVER part No.

38765019.

Cleaning secondary filter

Disconnect cleaner from electrical outlet.

3-3

3-4

Changing filter bag

Disconnect cleaner from electrical outlet.

Reattaching filter door

The filter door is designed with a “break-away” feature which allows it to snap free if it is pushed open too far.

To reattach, align hinges (C) of cover with slots on sides of filter area.

Press door back into place.

3-5

Cleaning final filter

The final filter assists in the filtration process to return clean air to the room.

To remove this filter when it becomes dirty, open the door on the side of the cleaner.

Lift out filter (B) and hand wash it in cold water with mild detergent.

Let filter air dry and reposition it on the side of cleaner. Make sure the green colored side of filter faces outward. Close door.

Should you want to replace this filter, ask for HOOVER part No.

40110004. Do not operate cleaner without

either the secondary or final filter in place.

3-6

Continued

➜

Belt replacement

The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner. The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition.

When to replace

Disconnect cleaner from electrical outlet.

To check belt, remove bottom plate as shown in “How to replace”. Replace belt if it is stretched, cut or broken.

What to buy

To assure effective operation, use only genuine HOOVER belts with your cleaner. When purchasing a new belt, ask for HOOVER part No. 38528033 (belt package part No.

40201160).

How to replace

Disconnect cleaner from electrical outlet.

Removing bottom plate

Place handle in low position and turn cleaner over so bottom side is up.

Remove the 4 screws as shown with a Phillips screwdriver.

Lift off bottom plate (A).

Installing new belt

With lettering on outside of belt and positioned as shown in box on (D), slide new belt over motor pulley (B).

Removing agitator brush roll

Remove agitator brush roll and used belt.

Discard used belt.

Replacing agitator brush roll

Insert agitator through belt and place belt in belt guide (C) on agitator.

Should the agitator shield (D) become dislodged while replacing the belt or the agitator, reposition it as shown noting the placement of its belt guide (E).

3-12

3-10

3-11

3-13

Check agitator shield

Because your cleaner picks up so well, we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters.

Removing debris under the shield will help maintain your cleaner’s excellent pick up and suction. Remove debris as follows:

1. Disconnect cleaner from electrical outlet.

2. Check for dirt accumulation by removing bottom plate (Fig. 3-10), removing agitator (Fig. 3-11), and lifting agitator shield (Fig. 3-13).

3. Remove any debris and replace shield, agitator and bottom plate (Figs. 3-13 to 3-15).

Headlight replacement (some models only)

What to buy

This cleaner uses a 12 volt, wedge base type 912 bulb, Hoover part No. 27313101.

Removing lens

Disconnect cleaner from electrical outlet.

Using a screwdriver, remove the two screws as shown and lift off lens.

Installing bulb

Pull old bulb straight out of socket. Push new bulb straight into socket until locked in place.

Excessive force is not required.

3-7

3-8

3-9

Replacing lens

Reposition lens and secure with the two screws.

+ 22 hidden pages