Hoover U5227-930, U5223-940, U5223-930, U5221-930, U5215-930 Owner’s Manual

Dimension TM Upright
Fig, 3
EXTRA BELT
EXTRA PAPER
1 Fig. 2
The Dimension" Upright series of cleaners was
first introduced in mid-1994 as replacements for
Legacy models. Fig. 1.
All models were introduced initially with:
,, Molded, integral handle grips
On/Off switch on the front of the upper handle
Two brush agitator (Replaceable Roll Sleeve)
Extra bag and belt storage on the unit Fig. 2
One 12v headlight
Hard bag enclosure
One speed motor
Stair cleaning handle
Four position carpet height adjustment Fig. 3
Top tool conversion
Triple stretch hose
Tool storage on the front of the unit
One molded extension wand
Type Z mlcrofiltratlen throw away bags
Fig. 5 l_ POSITION#5
Some models have a "check bag" indicator on the outside of the bag door. Fig, 4
Fig. 6
Oo_ ,,.%_;0°_
l ,_ ZOR POSITION R
I _ OFVALVE-_ !
=='_'-_ I GATE/F "--_
. ,- - AGITATOR
II
VALVE GATE IN CAVITY VALVE GATEIN
CARPET HEIGHT CLEANING TOOLS
POSITION
The cleaning tool hose attaches to the cleaner through the top of the hood and CAN stay attached
at all times.
When using cleaning tools, the nozzle control must be in the #5 cleaning tools position. Fig, 5
Withthe nozzle control inthe number 5 position, a valve gate in the main body closes and blocks all air
flow from the agitator cavity therefore diverting it to the hose.
Fig. 7
CORO SW,TCN
_) HOOK CONTROL
Libel. 1 ,AG
;_ CARPE'f MOTOR
EXTENSION
WAND
ADJU BELT
ON/OFF
TYPE Z
SAG
AGITATOR
Set on carpet, positions 1-4, the gate valve is opened allowing air to flow from the agitator cavity
to the motor. Fig, 6
To ensure maximum efficiency in the 4 floor cleaning
positions .b_o_Lb_hose ends must be firmly connected
to the cleaner base and tool rack Fig, 7 or the hose
removed completely and the tool door closed.
Refer to the Hoover Service Manual for repair proce dures and the Microfiche Parts Catalog - light brown
header - for spare parts.
SERVICE INSTRUCTIONS
LEGACY, LEGACY II, DIMENSION
& DIRT FINDER CLEANERS
Selv_ceDept. 1/96
Legacy/Legacy II
SWITCH
CONTROL
BUTTON
LOWER
JACKETSUPPORTLOWER
REAR WHEEL
CAM ACTUATOR IPRING
Legacy - Hard Bag
UPPl_
TOOL RACK
fBAO
TOOL DOOR
BPRING
!
MOTOR RETAINERLH
MOTOR RETAINER RH
I
WHEEL
ROITOM PLATIi
HANDLE BIJI.B
FRONTWHEEL* AGITATOR.
I KNOll
, WHEEL 8HAFT
NOZZLE HEIGHT
Dimension
f
j THROW AWAY BAG
TOOL DOOR
UPPER i
LOWER HANDLE
BAG HOUBINO --
TOOL DOOR
RPBING HOOD
LENB
IPPF..JROD
.TOOL
MOTOR
RETA)NER-RH
t
MOTOR
BULB
HANDLE LEVER
VALVE GATE
WHEEl. SUPPORT
_ AQ.ATOR
MAIN BODY
Dirt Finder
g
- Circuit Board
l
1
Microphone-
Note;
Only the components that
distinguish the Dirt Finder unit from the Dimension are listed.
I
Switch
Battery
Battery cover
I. General
These uprights are lightweight upright vacuums that feature high performance computer design motors, double edge cleaning, quick release cord
wraps and top conversion cleaning tools
ON/OFF _
SWITCH
All models have automatic height adjustment in that the nozzle is free to float up and down on the carpet. These models additionally have front wheel height control to limit the minimum nozzle
height which allows the user to "select the proper setting for optimum operation on various types of
carpets.
The Legacy and Legacy II models use Type "A" top-fill disposable bags.
The Dimension/Dirt Finder uses Type "Z" top-fill disposable bags.
Microfiltration bags are available for both models.
II. Operation
These cleaners operate on a Dirty Air System principle, i.e., dirty air passes through the motor
area (fan) before reaching the bag.
II
Fig. A
The carpet height adjustment lever has four settings for carpet cleaning and one for the top too!
conversion.
NOZZLE CONTROL KNOB _,_
It is important that the unit be in the proper setting (carpet - for floor cleaning, and cleaning tools -
when using the hose and tools). This will ensure
optimum performance.
The cleaning tool hose attaches to the unit through
the tool door located on the top of the hood. The air is directed to the hose by adjusting the nozzle
control knob to the cleaning tool position.
=o CLEAN AIR
,o DIRTY AIR
As illustrated, air and dirt are sucked through the molded agitator housing and directed into the motor area. The fan then propels the air and dirt up the handle passage and into the throw-away bag.
The Legacy units are controlled by an on/off switch located on the side of the unit. (Fig. A)
The Legacy II, Dimension and Dirt Finder units are controlled by an on/off switch located in the front of
the upper handle. (Fig. B)
The valve gate operates in conjunction with the height adjustment lever. When the lever is in any one of the four carpet settings the valve gate is
open. The cam is not contacting the valve gate.
Loading...
+ 15 hidden pages