Hoover U5063-930, U5065-930, U5059-930, U5067-930, U5057-930 Owner's Manual
...
HOOVER,
e
Upright
Vacuum Cleaner
When using an electrical appliance, always follow
basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
Warning .
injury:
n To reduce the risk of fire, electric shock, or
Do not use outdoors or on wet surfaces.
Close supervision is necessary when any appliance is used by or
near children. Do not allow vacuum cleaner to be used as a toy or
to run unattended at any time.
Keep hair, loose clothing, fingers, feet and all parts of bod
from openings, rotating agitator and other moving parts.
b
away
0 not
operate cleaner in bare feet or when wearing open toe shoes or
sandals.
Do not pick up anything that is burning or smoking, such as
cigarettes, matches, or hot ashes.
Do not use to pick up flammable or combustible liquids such as
gasoline or use in areas where they may be present.
Avoid picking up hard, sharp objects with the cleaner. They may
damage the cleaner and the bag.
A$w~ys
turn off this appliance before connecting or disconnecting
.
Do not use without dust bag or filters in place. Change bag fre-
quently when picking up very fine materials such as powder.
Use extra care when cleaning on stairs.
Do not put any object into openings. Do not use with any opening
M;;Ei;
keep free of dust,
Irnt, hair,
or anythmg that may reduce
.
Do not pull or carry by cord, use cord as a handle, close door on
cord or pull cord around sharp edges or corners. Do not run
appliance over cord. Keep cord away from heated surfaces.
A$va;,y,s
disconnect cord from electrical outlet before servicing the
.
Unplug cleaner when not in use. Turn off all controls before
unplugging.
Do not unplug by pulling on cord. To unplug, gras the plug, not
the cord. Never handle plug or appliance with wet
R
ands.
The use of an extension cord is not recommended.
Do not use with damaged cord or plug. If appliance is not working
as it should, has been dropped, damaged, left outdoors, or dropped
into water, take it to a Hoover Factory Service Center or Authorized
Hoover Warranty Service Dealer (Depot).
Use vacuum cleaner only for its intended use as described in the
instructions. Use only attachments recommended by The Hoover
Company; others may cause hazards.
Save these instructions!
Assembling cleaner
It is extremely important to read and follow all the instruction steps in order.
The assembled cleaner will look like
this drawing.
If you need assistance with any step
of the assembly, call
l-800-944-9200 for an automated
referral of authorized service outlet
locations (U.S. only) or
l-330-499-9499 to speak with a
representative in our Consumer
Response Center.
This cleaner is intended for house-
hold use.
FRONT
BACK
Remove all parts from carton
and identify each item shown.
Make sure all parts, especially
small items such as F and I,
are located before disposing
of cardboard packing.
A. Upper handle
B. Lower handle
C. Cord
D. Tool-rack
E. Bag compartment
F. Bracket
a
G. Cleaner body
H. Handle bolt and nut
F
packet
(one extra nut in-
cluded)
I.
Paper bag
J. Hose and cleaning tools
I
K. Wand(s)
(some models come with one
wand; others come with two.)
3
CORD
LOWER HANDLE
UPPER
HANDLE
Place upper and lower handle sections on a flat surface with cord
hooks on top. With hands on sides of handle sections, push
sections together firmly until they
“click”
into place (Fig. I).
*Do not press against the rod extending from the lower handle.
(Fig. 2) If the rod breaks or bends, the cleaner will not work
pro erl
CfY
.
Do not push handle together with your hands on the
en
s o the sections.
Note:
The
small red tab
above the ON/OFF switch is for
shipping
purposes only
and may fall off during assembly. If it does not fall
off, the tab will be removed during the final steps of assembly.
CORD PROTECTOR (slide
+)
*ROD
LOWER HANDLE
SWITCH
TAB HANDLE
I
Turn handle over. _ Insert
large
rectangular end of cord into
pocket in bottom of handle,
with
side marked “UP” visible.
(Fig. 2)
Make sure rectangular end is
pushed into the handle as far as
possible. (Fig. 3)
*ROD
CORD PROTECTOR
Slide cord
protector toward
upper handle.(Fig. 2)
Continued -D
4
PROTECTOR
Rotate cord protector on cord until you see its arrow. (Fig. 4)
/
CORD PROTECTOR
I
ARROWSz,
,
I
With arrow on cord protector
pointing toward arrow on upper
handle, press groove in cord
protector into slot in upper
handle. (Fig. 5 and 6)
CORD PROTECTOR
]
I-
Pull cord tight.
PROTECTOR
1
Press cord into place at each of the three notches indicated. (Fig. 7)
Do not plug cleaner in until assembly is totally complete.
5
I
RAILS
.
m
RAILS
I
Note location of tapered rails
on bracket and on lower
handle. (Fig. 8)
With printed side of bracket
facing up, slide rails on bracket
onto rails on lower handle until
bracket snaps past the lock
tab. (Fig. 9)
Pull bracket toward bottom of
handle slightly to make sure
bracket is locked in place.
Make sure hole in bracket
aligns with hole in handle.
With cord hooks to the back,
place assembled handle onto
handle base of cleaner body.
(Fig. 10)
Rock handle side to side
while pushing down firmly.
Extra pushing effort may be
required.
Continued
+
6
Push
bolt
into hole on lower
front of handle.
(Fig. 11)
If bolt will not go through hole
easily, check the following:
l
the bracket is properly
positioned (see Fig. 9)
l
the handle is pushed
completely down (see
Fig. 10).
Place
nut in
recessed area at
back of handle.
Hold nut in
place while tightening bolt
securely with a screwdriver.
(Fig. 12)
Note:
Only one nut is needed
on this model. The extra nut is
not required but has been
provided for your convenience.
With side of rack marked TOP
FRONT facing away from
cleaner handle, pull cord
through rack and lower rack
over handle as shown (Fig. 13).
Slide rack down handle.
Continue to slide rack down
until bottom of rack is below
lower cord hook. Snap one
side of rack then the other onto
lower handle (Fig. 14).
7
Slide rack down handle until
upper hooks snap into slots on
handle (Fig. 15).
Pull bag door latch forward and
remove door. Set bag door
aside. (Fig. 16)
Slide large tab on bottom, back
of bag compartment into slot
between the bracket and the
lower handle. (Fig. 17)
Note round opening and hooks
on back of bag compartment.
Place opening over dirt tube
and align hooks with slots in
handle.
Push
very
firmlyto
snap both
hooks into handle.
(Fig. 18)
Pull
on bag compartment to
make sure it is completely
snapped to handle.
Continued
-+
8
Align opening in paper bag with
dirt tube inside bag compartment. (Fig. 19)
Push bag collar
firmly
onto dirt
tube. (Fig. 20)
Tuck top and bottom of bag into
bag compartment.
To replace bag door, insert the
tabs on bottom of bag door into
the slots on bag compartment.
(Fig. 21)
Make sure all edges of paper
bag are completely inside the
bag compartment.
Close door.
Break
off red tab above ONOFF switch by pushing down
on tab. (Fig. 22)
Note: If tab has come off
during assembly make sure
switch is in the OFF position
. (down) before plugging cord
into an electrical outlet.
9
RED
TAB
ON/O
SWIT
CH
k
Loading...