®
turbopower
USER
INSTRUCTIONS
IMPORTANT SAFETY REMINDERS
User manual - This cleaner should only be
used for its intended purpose as described in
these instructions. Ensure that these are fully
understood before operating this appliance.
Only use attachments recommended or
supplied by Hoover.
When using cleaning tools, ensure that the
cleaner is kept in the upright (parked)
position. This will avoid possible damage to
the carpet or floor covering. When cleaning
stairs, DO NOT position the cleaner above you.
STATIC ELECTRICITY. Some carpets can
cause a small build up of static electricity. Any
static discharge is not hazardous to health.
DO NOT use your cleaner out of doors or
on any wet surface or for wet pick up.
Keep hands, feet, loose clothing and hair
away from rotating brushes.
DO NOT pick up hard or sharp objects,
matches, hot ashes, cigarette ends or other
similar items.
DO NOT pick up f lammable liquids such as
cleaning fluids, petrol, etc or their vapours.
Aerosol sprays may be flammable. DO
NOT spray near cleaner.
SUPPLY CORD. DO NOT run over the
supply cord when using your cleaner or
remove the plug by pulling on the supply cord.
FAULTS. DO NOT continue to use your
cleaner if it appears to be faulty. If the supply
cord is damaged stop using the cleaner
IMMEDIATELY. The supply cord must be
replaced by an authorised Hoover service
engineer to avoid a safety hazard.
AFTER USE. Switch the cleaner off and
remove the plug from the electricity supply.
Always switch off and remove the plug before
cleaning the appliance or attempting any
maintenance task.
This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved. Children
shall not play with the appliance.
Cleaning and user maintenance
shall not be made by children
without supervision.
HOOVER SERVICE. To ensure the continued
safe and efficient operation of this appliance
we recommend that any ser vicing or repairs
are only carried out by an authorised Hoover
service engineer.
Congratulations on the purchase of your
new Hoover Turbopower.
This highly advanced machine - with new
technology unique to Hoover - makes
cleaning easier and more efficient.
You’ll find it kinder to your carpets - and
to you!
Please take the time to read this manual
carefully.
You’ll then be ready to make the most of
the special features only the new Hoover
Turbopower can offer!
WARNING!
ELECTRICITY CAN BE
EXTREMELY DANGEROUS
In the unlikely event that any item is missing or you experience any problems with the product,
DO NOT TAKE IT BACK TO THE SHOP
Please contact the Hoover customer helpline:
Tel: 08444 995 599
Email: customer.services@hoovercandy.com
Should any faults occur with your cleaner during the first 12 months, contact the Hoover Customer
Helpline on the number above.
If you are having difficulty in obtaining filters or any other accessories for your cleaner contact the
Hoover Customer helpline or order online at www.hooverspares.com
This appliance is double-insulated and must not
be earthed.
The plug is fitted with a 13 amp fuse.
IMPORTANT:The wires in the mains lead are
coloured in accordance with the following
code:
Blue - NEUTRAL
Brown - LIVE
- 2 -
GETTING TO KNOW YOUR CLEANER
Effortless
cleaning
with your
new Hoover
Turbopower...
HANDLE
EXTRA LONG
HOSE HOOK*
When first unpacking your
cleaner please check all items are
included:
Cleaner body
Handle
Extension tube
Crevice Tool
Dusting Brush
Hose Hook
Pet Hair & Allergen Remover*
Hard Floor Caresse Nozzle*
(*Certain models only)
If any parts are missing contact
your retailer or call the Hoover
helpline on 08444 995 599
BIN RELEASE
WASHABLE
PRE MOTOR FILTER
DUST
CONTAINER
EXHAUST
FILTER
CARPET CARE
CONTROL
SELECTOR
DUSTING
BRUSH
ON/OFF
BUTTON
CLEANER
RELEASE
PEDAL
PET HAIR &
ALLERGEN
REMOVER*
HOSE HOOK/
CARRY HANDLE
CORD STORAGE
HOOK
HOSE
EXTENSION TUBE
/CREVICE TOOL
POWER CORD
HOSE
CONNECTOR
HARD FLOOR
CARESSE
NOZZLE*
* Certain models only
- 3 -
* Certain models only
PREPARING YOUR CLEANER
Insert the handle into the body
1
of the cleaner.
Connect hose to the main
5
ody of the cleaner.
* Certain models only.
Screw handle in place with the
2
screws provided.
Wrap hose around hose
6
hook.
Attach and screw hose hook in
3
place.
Attach the extension tube/crevice
7 8
tool to cleaner.
- 4 -
Attach turbo nozzle to the
4
cleaner.
Attach the dusting brush to
the cleaner.
CARPET CARE CONTROL SELECTOR
CLEANER RELEASE CLEANER STORAGE
The carpet care control selector raises and lowers the
height of the foot.
For typical carpets, the best carpet cleaning is achieved
by setting the selector to the SHORT PILE position.
For all other types of carpet try various settings until you
get the best result for your carpet.
Ensure that the cleaner is in an upright (parked) position.
Rotate knob to position best suited to depth of carpet pile.
Note: Using this cleaner for loop carpets or carpets
with pile greater than 30mm is not recommended.
Please consult the floorcare/carpet manufacturer’s
recommended cleaning instruction before vacuuming.
Unlock the cleaner by pressing down on the pedal
with your foot.
POWER SWITCH
To switch the cleaner on or off press down on the
pedal with your foot.
Turn the cleaner off and remove the plug. Wrap the
cord around the cord storage hooks.
For quick release of the full length of the power cord,
rotate the top storage hook.
!
IMPORTANT! When cleaning hard floors
such as vinyl or linoleum, move the selector
knob to the LONG PILE position. Failure to
do so may cause damage to the floor
surface.
* Certain models only.
- 5 -
CLEANING TOOLS*
Crevice Tool
For corners and hard to reach areas.
Dusting Brush
For bookshelves, frames, keyboards and other delicate areas.
Pet Hair & Allergen Remover*
The pet hair & allergen remover is ideal for removing pets hairs. DO NOT touch the rotating brush.
Hard Floor Caresse Nozzle*
The hard oor nozzle is ideal for cleaning delicate surfaces.
All accessories can t onto the end of the exible hose or end of the extension tube. Combine accessories
depending on use.
Remove the hose from the foot. Remove the extension tube. Slide the crevice tool out of the
1
2
3
extension tube.
CLEANING THE STAIRS
It is dangerous to place the cleaner above you when
cleaning stairs.
ALWAYS work with the cleaner below you. Ensure it is
positioned up against the bottom step.
LONGER LENGTH HOSE HOOK*
For longer length hose*. Use the upper hose hook for
storage.
Attach extension tube to the
4
end of the hose.
!
* Certain models only
Fit the crevice tool or dusting
5
brush to the extension tube or
hose.
IMPORTANT! When using cleaning tools, the cleaner must be kept in the upright position,
particularly when cleaning stairs. The nozzle height should also be set to tool mode.
Fit the pet hair & allergen
6
remover*Fit the hard oor
caresse nozzle* to the crevice
tool.
- 6 -
EMPTYING THE DUST CONTAINER
1
To remove the dust container from the
cleaner press the bin release button.
Hold the container
2
over the bin and
press the bin open
button.
CLEANING THE PRE MOTOR FILTERS
Rotate the upper part of the dust bin to open.
1
Remove the lter assembly from the dust bin.
2
CLEANING THE EXHAUST FILTER
Remove the dust container rotate and remove
1
the exhaust lter cover.
The dust container
43
door will open and
you can empty with
no contact with the
dust.
44
Once emptied, gently
tap or shake the
container to release
any excess dust from
the filters.
Separate the foam lter from the lter pack.
3
Wash both lters under hand warm water until
4
the water runs clean. Remove excess water by
shaking and leave to dry for 24 hours.
When completely dry reassemble and refit
filters to cleaner.
- 7 -
Remove the xhaust lter.
2
Wash the lter under hand warm water until
3
the water runs clean. Remove excess water by
shaking and leave to dry for 24 hours.
When completely dry reassemble and refit
filters to cleaner.
CHANGING THE BELT OR BRUSHES CLEARING A BLOCKAGE
If your cleaner is not picking up efciently, the belt or brushes (or both) may need replacing, but rst please make
sure you have:
• Emptied the dust container
• Cleaned the lters
• Checked for blockages
Turn the cleaner over and remove 5 retaining
1 4
screws attaching the brush guard to the
base.
Remove the brush guard
2
IMPORTANT: Switch the cleaner off and
remove the plug from the electricity supply
before dismantling cleaner
Hold the brush assembly and stretch the belt
until the brush can be slotted back into the
cleaner housing.
Rotate the brush to ensure movement of the belt.
5
IMPORTANT: Switch the cleaner off and
remove the plug from the electricity supply
before dismantling cleaner
If cleaning tools were
in use check the
cleaning tool and the
removable handle.
Check the hose by
removing it from the
cleaner, stretching it to
full length .
Turn the cleaner
over and rotate the
brushes until they
are free to rotate.
Remove brush assembly and check for wear
3
on the belt. Loop the new belt around the motor
and brush channel.
* Certain models only.
Refit the brush guard with 5 retaining screws.
6
- 8 -
Check for a blockage in
the hose socket. Use a
flexible rod to remove
any obstruction.
Removing a blockage from
the pet hair & allergen
remover.
Open the nozzle at each
side, lift cover and remove
the blockage.
*Certain models only.
Genuine HOOVER Spares
Quality
Tel. 08443 712 758
www.hooverspares.com
Always replace parts with genuine Hoover spares. When ordering parts,
always quote your model number.
Hoover Customer Helpline
Should any faults occur with your cleaner during the first 12 months,
contact the Hoover Customer Helpline on the number below.
Tel: 08444 995 599
Email: customer.services@hoovercandy.com
Hoover have a computerised nationwide service network of over 500
engineers who will quickly respond to your call and guarantee your repair
for 12 months.
SPARE PARTS CODE
AGITATOR Y27 35601200
BELT V33 35601222
HOSE D130 35601199
PET HAIR AND ALLERGEN
REMOVER
HARD FLOOR CARESSE
NOZZLE
CONSUMABLES CODE
FILTER KIT
(PRE MOTOR AND EXHAUST)
J44 35601064
G135 PC 35601201
U65 35601202
USE ONLY HOOVER SPARES
BSI ISO 9001
Hoover’s factories have been independently assessed for quality. Our products are
made using a quality system which meets the requirements of ISO 9001
Environment - WEEE Directive
This appliance is marked according to the European Directive 2011/65/EC on
Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly you will help prevent potential
otherwise be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as
household waste. Instead it shall be handed over to the appliance collection point for
recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with the local environmental regulations
for waste disposal.
For more detailed information about treatment, recovery and recycling of this product,
please contact your local city ofce, your household waste disposal service or the
shop where you purchased the product.
T
Hoover Limited Pentrebach, Merthyr Tydl, Mid Glamorgan CF48 4TU
negative consequences for the environment and human health, which could
his product complies with the European Directives 2006/95/EC, 2004/108/EC and
2011/65/EC.
GUARANTEE STATEMENT
The guarantee conditions for this appliance are as defined by our representative
in the country in which it is sold. Details regarding these conditions can be
obtained from the dealer from whom the appliance was purchased. The bill of
sale or receipt must be produced when making any claim under the terms of this
guarantee.
- 9 -
User checklist
WARNING
If your cleaner is not working properly run through the
following checklist.
1. Is there a working electricity supply to the cleaner?
Check with another electrical product.
2. Is the dust container full or choked with fine dust?
To empty the dust container, see instructions on P7.
3. Is the hose blocked?
To clear a blockage, see instructions on P8.
4. Is there a blockage in the cleaner base?
To clear a blockage, see the instruction on P8.
5. Are the filters blocked?
To clean filters, see the instruction on P7.
6. Is the nozzle height set correctly?
To set the carpet height selector, see the instruction on p4.
7. Are the brushes rotating correctly?
To check the brushes, see the instructions on p8.
8. Has the cleaner overheated?
If so, it will take about 30 minutes to reset.
A thermal cut out switches off the cleaner to prevent
overheating if it is used when full or there is a blockage or
dirty filters. If this should happen switch off, unplug and
correct the fault.
It will take approximately 30 minutes for the cut out to
automatically reset.
IMPORTANT
DO NOT RUN OVER THE POWER SUPPLY CORD
AS THIS COULD DAMAGE THE SUPPLY CORD
INSULATION.
If there is any doubt, call the Hoover customer Helpline 08444 995 599 for
advice. They may be able to assist you over the telephone.
- 10 -
© 2011 48003559/04
INDUSTRIAL
DESIGN
Artwork Number:
Issue:
48003559 04
Title:
sonix User manual
Created:
Cris
Modified:
Cris 2013/02/27
Engineering Approved:
Hoover Ltd.
Industrial Design Department
5th Floor, 288 Dongping Street,
Suzhou Industrial Park,Suzhou,
PRC 215123
Tel: 0512-82181000 Ext 225
Printing colour : (单黑)black
Date:
Date:
Date:
Note:
Artwork not to be used
unless approved by
Engineering.
Size :A4(297x210mm)
Material: 1.cover=(铜版纸)coated paper(120g)
2.inside pages=（双胶纸）offset paper(80g)
Loading...