Page 1
USER MANUAL
Page 2
- 2 -
IMPORTANT SAFETY REMINDERS
This appliance should only be used for domestic cleaning, as
described in this user guide. Please ensure that this guide is
fully understood before operating the appliance.
Do not leave the appliance plugged in. Always switch off and
remove the plug from the socket after use, or before cleaning
the appliance or any maintenance task.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
If the power cord is damaged stop using the appliance
immediately. To avoid a safety hazard, an authorised Hoover
service engineer must replace the power cord.
Keep hands, feet, loose clothing and hair away from rotating
brushes.
Use only attachments, consumables or spares recommended
or supplied by Hoover.
When using cleaning tools ensure that the appliance is kept in
the upright (parked) position. This will avoid possible damage
to the carpet or floor covering. When cleaning stairs, do not
position the appliance above you.
Static electricity: some carpets can cause a small build up
of static electricity. Any static discharge is not hazardous to
health.
Do not use your appliance out of doors or on any wet surface
or for wet pick up.
Do not pick up hard or sharp objects, matches, hot ashes,
cigarette ends or other similar items.
Do not spray with or pick up flammable liquids, cleaning fluids,
aerosols or their vapours.
Do not run over the power cord when using your appliance or
remove the plug by pulling on the power cord.
Do not continue to use your appliance if it appears faulty.
Hoover service: To ensure the continued safe and efficient
operation of this appliance we recommend that any servicing
or repairs are only carried out by an authorised Hoover service
engineer.
Do not stand on or wrap the cord around arms or legs when
using your appliance.
Do not use the appliance to clean animals or people.
When using the cleaning tools, ensure to always steady the
appliance with your other hand. This will ensure that the
appliance does not fall while in use.
WARNING: A thermal cut out switches off the appliance to prevent overheating
if it is used when full or there is a blockage or dirty filters. If this should
happen then switch off, unplug and correct the fault. It will take approximately
45 minutes for the cut out to automatically reset.
The Environment
The symbol on this appliance indicates that this appliance may not
be treated as household waste. Instead it must be handed over to the
applicable collection point for the recycling of electrical and electronic
equipment. Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more detailed
information about treatment, recovery and recycling of this appliance, please
contact your local city office, your household and waste disposal service or
the shop where you purchased the appliance.
This appliance complies with the European Directives 2006/95/EC,
2004/108/EC and 2011/65/EU.
HOOVER Limited, Pentrebach, Merthyr Tydfil, Mid Glamorgan, CF48 4TU, UK
Page 3
Effortless
cleaning
with your
new Hoover
PET HAIR & ALLERGEN
REMOVER*
HANDLE
CORD
CLIP
POWER CORD
2 IN 1 TOOL
CLEANER
RELEASE
PEDAL
ON/OFF
PEDAL
HANDLE
BIN RELEASE BUTTON
BIN
EXHAUST
FILTER GRILLE
CARPET CARE
SELECTOR
**
HOSE SOCKET
GETTING TO KNOW YOUR CLEANER
WASHABLE HEPA
FILTER & MESH
FRAME
- 3 -
HOSE STORAGE
HOOK
HOSE
EXTENSION
TUBE AND LONG
CREVICE TOOL
* Certain models only
**Selector design, top of the bin and handle may vary according to models.
CORD STORAGE
HOOK
PARQUET NOZZLE*
This vacuum cleaner is
supplied with an Energy
Label as required by
European Regulation (EU)
665/2013.
Page 4
PREPARING YOUR CLEANER
SUPPLY CORD
Insert the main handle in the cleaner body
and then x it with the screw provided.
To tighten the screw you can use a
standard coin.
Do not run over the supply
cord.
Clip the supply cord in the cord
clip at the back of the handle
to avoid accidentally running
the cleaner over the cord and
causing any damage.
CARPET CARE CONTROL SELECTOR
CARPET CARE CONTROL SELECTOR
The carpet care control selector raises and lowers
the height of the nozzle.
CLEANER RELEASE
Unlock the cleaner by pressing down on the left pedal
with your foot.
POWER SWITCH
To switch the cleaner on or off press down on the right
pedal with your foot.
- 4 -
3
4
1
2
5
* Certain models only
RELEASE
Ensure that the cleaner is in the upright (parked)
position and move the selector to the required
setting for the carpet type or oor covering.
To obtain the best performance and energy
efciency
#1
it is recommended that the adjustment
setting position 1 is used for the main cleaning
operations. The other adjustment settings are
for ease of use, use on longer pile carpets, or for
specialist cleaning tasks.
Settings
1. Best performance and energy efciency, short to
medium pile carpets, hard wooden oors, wooden
oor boards with crevices, ceramic tiles.
2. Medium pile carpets, delicate oor coverings
such as vinyl or linoleum, parquet ooring.
3 or 4. For longer pile carpets the motion
resistance may increase. Use these intermediate
settings to reduce the force required to push the
vacuum cleaner.
5. Luxury carpet and Tool mode
IMPORTANT: Using this cleaner for loop pile
carpets with pile greater than 30mm is not
recommended. Please consult the oorcare/carpet
manufacturer’s recommended cleaning instruction
before vacuuming.
IMPORTANT: When cleaning delicate hard oors
such as vinyl or linoleum the selector switch must
be moved to position 2. Failure to do so may cause
damage to the oor surface.
This vacuum cleaner is supplied with an Energy
Label as required by European Regulation (EU)
665/2013. If the label shows a red prohibition
circle on the right covering the hard oor symbol,
then this indicates that the vacuum cleaner is not
suitable for use on hard oors.
#1
NOTE: Dust pick up ability carpet, dust pick up
ability hard oor, and energy efciency in accord
with Commission Regulations (EU) 665/2013 and
(EU) 666/2013.
Page 5
CLEANING TOOLS
!
IMPORTANT! When using cleaning tools, the cleaner must be kept in the upright position,
particularly when cleaning stairs. The nozzle height should also be set to tool mode.
Remove hose from the hose
socket.
Remove the long crevice tool
from the extension tube.
Fit the extension tube to the
hose.
Attach the long crevice tool to
the extension tube or directly to
the hose.
Fit the dusting brush or the
Pet Hair and Allergen Remover*
or parquet nozzle* to the hose or
at the end of the extension tube.
Handle
All accessories can t onto the end of the hose. Combine accessories depending on use.
Pet Hair & Allergen Remover*
The pet hair & allergen remover is ideal for removing pet hairs.
DO NOT touch the rotating brush.
1
4
2
5
3
6
CLEANING THE STAIRS
STORING THE CLEANER
It is dangerous to place the cleaner
above you when cleaning stairs.
ALWAYS work with the cleaner
below you. Ensure it is positioned
up against the bottom step.
Turn the cleaner off and remove the plug. Wind the
power cord around the cord storage hooks.
- 5 -
Pull out extension tube and
long crevice tool.
* Certain models only
Page 6
EMPTYING THE BIN
Hold the container over
the Bin and press the
easy open button at the
rear of the container.
The bin door will open
and you can empty into a
bin with no dust contact.
Once emptied, gently tap
or shake the container to
release any excess dust
from the filters.
Do not overfill the bin
above the max level line.
2
43
To remove the bin from the cleaner press the
bin release button.
1
CLEANING THE PRE MOTOR FILTERS
Rotate the upper part of the dust bin to open.
1
Remove the lter assembly from the bin top by
rotating the lter. It is advisable to wash the lters
after every 5 bin empties.
2
Remove the mesh frame from the
HEPA lter, then gently tap both lters
to release any excess dust.
3
Wash both lter and protective mesh under warm
water until the water runs clean. Remove excess
water by shaking and leave to dry for 24 hours.
Reassemble and ret lters to cleaner, only when
they are completely dry.
4
CLEANING THE EXHAUST FILTER
The exhaust filter should be washed every month.
Press down on the latch to remove the exhaust grille.
Remove filter and wash with warm water.
Remove excess water by shaking and leave to dry for
24 hours. Refit filters only when completely dry.
!
IMPORTANT! Ensure the mesh frame is
reassembled to the HEPA lter before use
- 6 -
1
2
Page 7
CHANGING THE BELT OR BRUSHES CLEARING A BLOCKAGE
IMPORTANT: Switch the cleaner off and
remove the plug from the electricity supply
before attempting any maintenance.
IMPORTANT: Switch the cleaner off and
remove the plug from the electricity supply
before attempting any maintenance.
If your cleaner is not picking up efciently, the belt or brushes (or both) may need replacing, but rst
please make sure you have:
• Emptied the bin
• Cleaned the lters
• Checked for blockages
Turn the cleaner over and remove 6
retaining screws attaching the brush guard
to the base.
Remove the brush guard
Hold the brush assembly and stretch the
belt until the brush can be slotted back
into the cleaner housing.
Rotate the brush to ensure free movement
of the belt.
Refit the brush guard with 6 retaining screws.
1 4
2
3
5
6
Check the cleaning
tools and hose for
blockages.
The hose can be
removed at both ends.
Turn the cleaner
over and rotate the
brushes to identify
any obstructions
including hair.
Check for a blockage in
the hose socket. Use a
flexible rod to remove
any obstruction.
To clear a blockage
in the Pet Hair &
Allergen Remover*, twist
the collar at the rear and
lift the cover.
- 7 -
*Certain models only
Remove brush assembly and check for
wear on the belt.
Loop the new
belt around the
motor and brush channel.
Page 8
- 8 -
User checklist
If your cleaner is not working properly run through the
following checklist.
1. Is there a working electricity supply to the cleaner?
Check with another electrical product.
2. Is the bin full or choked with fine dust?
To empty the bin, see instructions on P6.
3. Is the hose blocked?
To clear a blockage, see instructions on P7.
4. Is there a blockage in the cleaner base?
To clear a blockage, see the instruction on P7.
5. Are the filters blocked?
To clean filters, see the instruction on P6.
6. Is the nozzle height set correctly?
To set the carpet height selector, see the instruction on p4.
7. Are the brushes rotating correctly?
To check the brushes, see the instructions on p7.
8. Has the cleaner overheated?
If so, it will take about 30 minutes to reset.
If there is any doubt call the Hoover Service Office for advice. They may be able
to assist you over the telephone. A service charge will be made if the cleaner is
examined and found to be in working order, has not been assembled in accordance
with these instructions or has been used incorrectly. working order, has not been
assembled in accordance with these instructions or has been used incorrectly.
WARNING!
A thermal cut out switches off the cleaner to prevent overheating if it is used when
full or there is a blockage or dirty filters. If this should happen switch off, unplug and
correct the fault.
It will take about 45 minutes for the cut out to automatically reset.
IMPORTANT: Do not run cleaner over the supply cord as this could damage the
supply cord insulation.
IMPORTANT INFORMATION
Hoover Service
Should you require service at any time, please contact your local Hoover Service
Ofce.
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local
Hoover dealer or direct from Hoover. When ordering parts always quote your model
number.
GUARANTEE STATEMENT
The guarantee conditions for this appliance are as defined by our representative
in the country in which it is sold. Details regarding these conditions can be
obtained from the dealer from whom the appliance was purchased. The bill of
sale or receipt must be produced when making any claim under the terms of this
guarantee.
Subject to change without notice.
Quality
Hoover’s factories have been independently assessed for quality. Our products
are made using a quality system which meets the requirements of ISO 9001
Page 9
Hoover Limited
Pentrebach
Merthyr Tydl
Mid Glamorgan
CF48 4TU
HOOVER CUSTOMER HELPINE
08444 995 599
© 2014 48011551
Page 10
INDUSTRIAL
DESIGN
Artwork Number:
Title:
Created:
Modified:
Engineering Approved:
Issue:
Date:
Date:
Date:
Hoover Ltd.
Industrial Design Department
5th Floor, 288 Dongping Street,
Suzhou Industrial Park,Suzhou,
PRC 215123
Tel: 0512-82181000 Ext 226
Note:
Artwork not to be used
unless approved by
Engineering.
Cris 2014/04/30
Cris 2014/04/30
user manual & manual label
MANUAL LABEL
USER MANUAL
Printing colour : 黑（black）
Size : 297x210mm
Material: 1.cover= 铜版纸 coated paper(120g)
2.inside pages= 双胶纸 offset paper(80g)
Printing colour :
黑（black）
Size : 75x50mm
Material: Adhesiver sticker (不覆膜不干胶)
Background Colour：White（白色底）
stick
TH71 SM01 - 001 - 39100399
220-240V~50Hz
750W 5.8Kg
Loading...