Hoover®Canister Cleaner
with Power Nozzle
Owner’s Manual
Thank you for selecting a HOOVER®product.
This cleaner was inspected and packaged carefully before being shipped from the
factory. If you should happen to need assistance during assembly or operation, call
1-800-944-9200 for automated referral of authorized service
outlet locations (U.S. only) or
1-330-499-9499 to speak with a representative in our Consumer
Response Center.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
Fill in and retain
The model and serial number are located on the bottom of the cleaner.
For your personal records, please enter the COMPLETE model and serial number in
the spaces provided and retain this information.
Your cleaner is model________________________________________________________
and has serial number ______________________________________________________
It is suggested that you attach your sales receipt to this owner’s manual. Verification of
date of purchase may be required for warranty service of your Hoover product.
Index
Assembling Cleaner ............................3-4
Cleaner Description................................3
How To Use
Canister cleaner ..............................4-6
Check Bag Indicator ..........................4
Cleaning Tools ................................5-6
Power Nozzle ..................................4-5
To clean stairs ....................................6
If You Have a Problem..........................10
Important Safeguards ............................1
Lubrication..............................................9
Maintenance
Cleaning Filters ................................7-8
Clearing Blockages ............................6
Replacing Agitator ............................9
Replacing Bag ................................6-7
Replacing Belt ....................................8
Replacing Headlight ..........................9
Service....................................................9
Storage ..................................................6
Warranty................................................10
Important Safeguards!
When using an electrical appliance, always follow
basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
Warning:
• Do not use outdoors or on wet surfaces.
• Close supervision is necessary when any appliance is used by or near children.
Do not allow vacuum cleaner to be used as a toy or to run unattended at any
time.
• Keep hair, loose clothing, fingers, feet and all parts of body away from openings,
rotating agitator and other moving parts. Do not operate cleaner in bare feet or
when wearing open toe shoes or sandals.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes.
• Do not use to pick up flammable or combustible liquids such as gasoline or use
in areas where they may be present.
• The hose contains electrical wires. Do not use if damaged, cut or punctured.
• Avoid picking up hard, sharp objects with the cleaner. They may damage the
cleaner and the bag.
• Always turn off this appliance before connecting or disconnecting hose or
motorized nozzle.
• Do not use without dust bag or filters in place. Change bag frequently when picking up very fine materials such as powder.
• Use extra care when cleaning on stairs.
• Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, or anything that may reduce air flow.
• Do not pull or carry by cord, use cord as a handle, close door on cord or pull
cord around sharp edges or corners. Do not run appliance over cord. Keep cord
away from heated surfaces.
• Always disconnect cord from electrical outlet before servicing the cleaner.
• Unplug cleaner when not in use. Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Never handle plug or appliance with wet hands.
• If cleaner has a cord reel, hold on to the plug while cord is being rewound to prevent cord from whipping.
• The use of an extension cord is not recommended.
• Do not use with damaged cord or plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, take it to a
Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer
(Depot).
• Use vacuum cleaner only for its intended use as described in the instructions.
Use only attachments recommended by The Hoover Company; others may cause
hazards.
Save these instructions!
To reduce the risk of fire, electric shock or injury:
1
Review this manual
before operating
cleaner
© 1992 The Hoover Company
www.hoovercompany.com
2
Unpack cleaner from carton and
identify the parts shown.
Remove and dispose of cardboard
packing.
A. Canister cleaner
B. Power nozzle
C. Extra paper bag (one bag is
installed in cleaner)
D. Extension wands and hose
A
B
C
D
1. Combination carpet and floor
power nozzle: automatically
adjusts to different carpet pile
heights.
2. Headlight
3. Spring latch: locks extension
wands together or locks wand to
nozzle or tool.
4. Wand storage clip*: place cleaner
on its end and hook clip onto bottom
of cleaner.
5. Extension wands: used with rug
and floor nozzle. One or both
wands may be used with cleaning
tools.
6. Wand/tool latch: used to lock hand
grip to extension wands or cleaning
tools.
7. Floor surface selector button*:
push button toward “RUG” for carpet
cleaning or “BARE” for hard surface
floor cleaning.
8. Hand grip
9. Remote ON/OFF switch*: located
on the hand grip for convenient
cleaner operation.
10.Remote variable speed control*:
allows user to manually select
cleaner speed at the hand grip.
11. Receptacle: connect power nozzle
cord underneath hand grip.
12. Dusting brush
13. Crevice tool
14. Hard floor tool
15. Furniture nozzle
16. Power ON light*: glows when
cleaner can be controlled at the
hand grip.
17. Suction regulator*: close for
maximum suction, open if power
nozzle is difficult to push or light
weight rugs or draperies are being
cleaned.
18. Large wheels: provide easy towing
when cleaner is pulled over carpet,
area rugs and door sills.
19. Cord rewind pedal: step on pedal
to rewind cord for storage. Hold
plug until cord is rewound.
20. Micro filter: aids in filtration of dirt
particles.
21. Tool lid: pull up on edge of lid in
recessed area.
22. Bag lid latch: lift to open bag lid.
23. ON/OFF pedal: conveniently
located on top of cleaner.
24. Check bag indicator: shows red
when paper bag should be
checked for fullness.
25. Hose connector
26. Receptacle: connect power nozzle
cord to canister cleaner.
27. Carrying handle
28. Belt check window*: motor pulley
will be visible in window if belt is
broken.
*Available on some models.
This cleaner is intended for house-
hold use.
1
2
3
4
5
6
6
17
11
11
12
13
14
16
18
19
20
21
22
23
24
25
26
27
28
15
7
7
8
8
9
9
10
10
1
1
2
2
The assembled cleaner will look like
the drawing.
Operate cleaner only at voltage specified on data plate on bottom of cleaner.
Unpacking
Cleaner
description
POWER
SURFACE
FLOOR
SPEED
To attach the hose to the extension
wands, push latch (F) on the hand
grip to the unlock symbol.
Push the hand grip (G) down onto wand
so that the button projection (H) fits into
the slot. Push the latch to the lock
symbol to secure wand.
Attach second wand to the first.
Position cord into cord clips (E) on
wands, placing excess cord between
nozzle and bottom cord clip.
Note: Bottom cord clip is on wand storage clip.
Insert plug as deeply into the
receptacle as possible. Latch (A)
will automatically fasten. Cleaner will
not operate unless plug is inserted into
receptacle.
To disconnect hose, first remove hose
cord plug from receptacle while pulling
out on latch. Then, depress buttons
(shown in Fig. 3 by arrows) on hose
connector and pull up.
Note: The flexible hose contains
electrical wires for connection to the
power nozzle and should not be used
if damaged. The wires should not be
seen through the outer skin.
Connect hose
With hose toward front of cleaner,
push hose connector into opening
in bag lid.
When hose is attached properly, hose
cord plug will reach to receptacle on
cleaner.
3
3
3
4
4
Questions or
Concerns?
The Hoover Company wants to quickly
resolve any concerns about your cleaner
or questions regarding its use. Look on
the list provided with the product for
your local Hoover Factory Service
Center or in the Yellow Pages under
“Vacuum Cleaners - Household” for the
nearest Authorized Hoover Warranty
Service Dealer (Depot) or call:
1-800-944-9200 for an automated
referral of authorized service outlet
locations (U.S. only OR
1-330-499-9499 to speak with a representative in the Hoover Consumer
Response Center OR
Visit us online at
www.hoovercompany.com to find the
service outlet nearest you (click on the
“Service” button).
PLEASE DO NOT RETURN THIS
PRODUCT TO THE STORE OR SEND
IT TO NORTH CANTON FOR SERVICE.
A
B
Attach nozzle and wands
The wand with the storage clip
connects to the power nozzle.
Attach it to power nozzle by fitting button projection (B) on nozzle connector
(C) into opening near end of wand. Be
sure nozzle is locked in place.
To release, press down on center of
latch (D) and remove nozzle.
5
5
C
E
G
H
6
6
7
7
Continued
➟
D
F
How to assemble
Floor surface selector
(some models)
Carpet or rug cleaning
When using the power nozzle for
carpet and rug cleaning, push the
floor surface selector button toward
“RUG” (A). This setting provides the
suction and agitator action necessary to
deep clean carpets. The nozzle adjusts
automatically to various carpet pile
heights.
Deluxe power
nozzle
Handle positions
The handle has two positions
when used with the power nozzle:
upright and operating.
To lower handle to operating position,
place your foot firmly on the power nozzle and pull handle back.
Check bag indicator
The indicator will begin to show red
as bag fills with dirt. There are three
conditions that will cause the indicator to
become completely red:
1. The bag is full; change the bag.
2. Very fine materials (such as powder)
have been picked up, clogging the bag
pores; change the bag, even if it is not full.
3. There is a blockage in the nozzle, hose,
tools, or at the bag opening; remove the
blockage.
On some models two switches are
used to turn the cleaner on for operation.
Press remote control switch (C) on
hand grip to the “OFF” position
before plugging cord into electrical outlet.
Plug cord into an electrical outlet and
step on ON-OFF pedal. The POWER
ON light will glow, indicating that the
cleaner can then be controlled at the
hand grip. Press hand grip switch to
the ON position.
POWER
FLOOR
SURFACE
O
F
F
O
N
B
A
R
E
R
U
G
ON-OFF switches
After assembling cleaner, plug
cord into electrical outlet. Turn
cleaner on by depressing ON-OFF
pedal (A). To turn cleaner off, depress
pedal again.
Note: Pedal opposite ON-OFF pedal is
Cord Rewind Pedal (B).
4
Push plug on power nozzle cord
completely into receptacle
underneath hand grip.
Always disconnect cleaner from elec-
trical outlet before attaching or
removing power nozzle plug.
8
8
9
9
10
10
To reduce the risk of electric shock, this
appliance has a polarized plug (one
blade is wider than the other). This
plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to
install the proper outlet. Do not change
the plug in any way.
A
C
B
11
11
12
12
POWER
FLOOR
SURFACE
O
F
F
O
N
B
A
R
E
R
U
G
13
13
A
How to use
Select the proper tool
A. Crevice tool may be used in
tight spaces, corners, and along
edges in such places as dresser drawers, upholstered furniture, stairs and
baseboards.
B. Furniture nozzle may be used for
upholstered furniture, draperies, tapestries, mattresses, clothing, automobile
interiors and carpeted stairs.
C. Dusting brush may be used for
carved furniture, table tops, books,
lamps, lighting fixtures, venetian blinds,
baseboards, shutters and registers.
D. Hard floor tool may be used for
walls and very irregular hard surface
floors such as brick and slate.
Suction regulator
(some models)
The suction regulator on the wand
allows the user to reduce suction
when necessary. Open the suction
regulator for less suction when cleaning
lightweight fabrics or throw rugs. Close
(A) the suction regulator for maximum
suction.
If the power nozzle is difficult to push
on some carpet, open the suction regulator. This will help prevent damage
to the belt.
Variable speed control
(some models)
The variable speed control (A) is
located on the hand grip.
Slide the control back to reduce energy
consumption and to clean lightly soiled
areas or delicate fabrics. Slide control forward for maximum cleaning power in
heavily soiled areas. If the power nozzle is
difficult to push, slide the control toward
back to reduce the power. This will help
prevent damage to the belt.
Brushed edge cleaning
Brushed edge cleaning is provided
on both sides of the nozzle to
remove embedded dirt in carpet
near baseboards and furniture. Guide
side of nozzle parallel to edge of carpet or
furniture as shown.
Hard surface floor cleaning
The power nozzle can be used for
cleaning hard surface floors such
as wood, linoleum, vinyl, asphalt
and rubber tile, sealed cork, concrete
and terrazzo, as well as carpet.
To set the power nozzle for hard surface
floor cleaning, push the floor surface
selector button toward “BARE” (B). This
setting provides suction and no agitator
action. If you prefer, you may use the
wall/floor brush to clean bare floors.
You will find it particularly convenient
when cleaning lightweight area rugs to
set the floor surface selector button on
“BARE” and continue cleaning the surrounding floor surfaces.
Note: The headlight will be ON in both
the “RUG” and “BARE” floor surface
modes
.
5
POWER
FLOOR
SURFACE
O
F
F
O
N
R
U
G
B
A
R
E
14
15
POWER
FLOOR
SURFACE
SPEED
O
F
F
O
N
B
A
R
E
R
U
G
16
16
15
14
B
A
17
17
A
18
18
Cleaning tools
The cleaning tools are conveniently
stored in the cleaner underneath the tool
lid. Pull up on edge of lid in recessed
area to open.
The lid is also designed with a “breakaway” feature which allows it to snap off
if it is pushed open too far. To re-attach,
align small knobs on hinge area of lid
with slots at rear of cleaner; press lid
back into place.
The cleaning tools have many uses.
best suited for the cleaning task from
the descriptions left.
A
B
C
D
Filter bag
When to replace
Check the bag when the “CHECK BAG”
indicator shows red. When bag is filled
with dirt, the cleaner will not operate efficiently. Discard used bag.
CAUTION: Very fine materials, such
as face powder, cornstarch, fireplace
ashes or fireplace soot, may seal the
paper bag and may cause it to burst
even though it is only partially full of
dirt. When the cleaner is used to
remove material of this nature,
change the bag often.
Where to buy
Filter bags may be purchased from
Authorized Hoover Dealers (Depots),
Leading Retailers, Hoover Factory
4.Make sure power nozzle plug is
disconnected from hand grip.
Then check for blockage in nozzle connector (A).
Push nozzle connector down to lowest
position. Look into nozzle connector
and remove any blockage.
2. Plug cleaner in, turn on, and
check hose end for suction.
Remove any obstructions.
Clearing blockages
Low suction or pick up may be due to a
blockage in the system. Refer to the
following steps to check for blockages,
continuing with each step until the
blockage is found:
1.Turn cleaner off and disconnect from
electrical outlet; then disconnect
power nozzle plug and wands from
hand grip.
How to clean stairs
Clean stairs by placing cleaner on
end. Clean stairs from bottom to
top.
Wand storage clip
(some models)
To save storage space, stand the cleaner on end and hook wand storage clip
on bottom of cleaner. The nozzle must
be positioned down as shown.
Lift up on wand to remove storage clip
from cleaner.
How to store cleaner
The cleaning tools are conveniently
stored in the cleaner, as shown. To
replace the wall/floor brush, be sure to
turn the nozzle connector toward the
cord rewind pedal (A) before pushing
the brush in place.
To connect tools to metal wands,
insert end of tool into wand and
snap into position. To disconnect, press
down on the center of spring latch and
remove tool.
6
How to connect
To use the cleaner with tools, disconnect the power nozzle from the
hand grip.
Tools may be attached directly to the
hand grip. With the latch in the unlock
position, insert tool (or wand if extra
length is needed), then push latch to the
lock position to secure.
To remove the tool (or wand), push the
latch to the unlock position.
19
19
20
21
22
24
25
25
24
22
23
23
21
20
Familiarize yourself with these home
maintenance tasks as proper use and
care of your cleaner will ensure continued cleaning effectiveness.
A
3. Remove power nozzle from wands
and attach wands to hose. Check for
suction and remove any blockages.
A
Maintenance
How to replace
Disconnect cleaner from electrical
outlet.
Service Centers, or through The Hoover
Company online at
www.hoovercompany.com
What to buy
In order to maintain the original cleaning
effectiveness and superior filtration
qualities of your cleaner, use only
Genuine HOOVER® Allergen
Filtration Type S disposable filter bags.
Regular HOOVER® Type S disposable
bags also fit your cleaner and will give
satisfactory performance.
To assure that your HOOVER cleaner
operates at peak performance, it is
imperative that you use only genuine
HOOVER filter bags made by The
Hoover Company. HOOVER bags can
be identified by these trademarks—
7
26
27
28
29
Continued
➟
®
B
A
Rotate hose to the side, lift bag lid
latch and open bag lid.
26
Carefully pull out used bag.
27
Form new bag into a box-like
shape. Slide bag collar firmly into
holder.
28
Push rear edge of bag into bag
cavity below seal (A).
Clear bag opening (B) by pushing the
pierced paper through opening toward
bag interior.
Close bag lid.
29
30
How to attach bag lid
The bag lid and hinges are
designed with a “break- away”
feature. If the lid is pushed open
too far, it will come off. It can be easily
re-attached by aligning the hinges with
the appropriate slots in the cleaner, as
shown.
30
Filterssecondary and micro
How to clean
Disconnect cleaner from electrical
outlet.
The secondary filter, located
behind the grill in the bag compart-
ment, protects the motor from dirt parti-
31
31
cles. If filter becomes dirty, pull off grill
and lift out filter. Wash filter in warm
water or replace it with a new one. A
dry filter must be put back into cleaner.
Do not operate cleaner without sec-
ondary filter in place.
The micro filter aids in the filtration
process to return clean air to the
room. To remove this filter, open tool lid,
remove dusting brush and pull up red filter cassette.
32
32
Position nozzle cover on front lip of
nozzle base. Press cover into
place.
Turn nozzle over and replace screws.
Stretch belt back and attach to
motor pulley.
Hold opposite end of agitator in place.
Push belt end forward, rotating end plate
until it slides into place. Turn agitator,
making sure it rotates freely.
If belt is not broken, pull it off the
motor pulley (A).
Return nozzle to original position,
lift off nozzle cover.
Lift up end of agitator. Remove old
belt from agitator pulley and replace
with new belt. Lettering on belt must be
visible.
How to replace
Disconnect cleaner from electrical
outlet and disconnect power nozzle
from extension wands.
Turn nozzle over and unscrew the
4 recessed Phillips head screws.
Note: Do not remove the 3 screws in
the triangle formation as these hold
the motor in place.
When to replace
For some models, the belt is visible
through the belt check window on top of
the nozzle. If the belt is broken, the motor
pulley will be visible through the window.
The belt should be checked from time to
time to be sure it is in good condition. To
check, remove the nozzle cover (see following section). Replace the belt if it is
stretched, cut, or broken.
Belt replacement
The belt in your power nozzle drives the
agitator. It has been designed specifically for use in this cleaner and is important
for effective operation.
What to buy
There are other belts manufactured that
are similar in shape and size, but are not
designed for the HOOVER power nozzle.
Such belts do not operate the agitator correctly and may create stress which could
damage your power nozzle. Use only a
genuine HOOVER Belt No. 38528-011
when a belt replacement is necessary.
If filter is dirty, open grid on cas-
sette and remove filter. Wash filter
in warm water or replace it with a new
one. A dry filter must be put back into
cleaner.
8
33
34
35
36
37
38
39
39
38
37
36
35
34
A
B
C
33
9
40
41
Continued
➟
Agitator replacement
When to replace
Disconnect cleaner from electrical
outlet.
When agitator brushes are worn, the agitator should be replaced.
To check condition of brushes,
move edge of a card across bottom
plate while turning agitator. To maintain
cleaning effectiveness, replace agitator if
brushes do not touch card.
40
What to buy
The agitator may be replaced with either
a single or double row of brushes.
Single row of brushes Hoover part No. 48414-051.
Double row of brushes Hoover part No. 48414-049.
How to replace
Disconnect cleaner from electrical
outlet.
1. Remove nozzle cover, agitator and belt
as shown in “How to replace belt.”
2. Discard old agitator.
3. Replace new agitator and belt as
shown in steps 4-6 of “How to replace
belt”.
Headlight replacement
The headlight, located on top of the
power nozzle, operates when the cleaner
is turned on. Use only Hoover part NO.
27317-307, which is a fused bulb, when
replacing the headlight.
How to replace
Disconnect cleaner from electrical outlet and disconnect power nozzle from
extension wands.
1. Remove the nozzle cover as shown in
“How to replace belt”.
2. Push old bulb into socket and
twist to remove. Push new bulb into
socket and twist into place.
3. Replace nozzle cover.
41
Lubrication
The motor is equipped with two bearings
that contain sufficient lubrication for the
life of the motor. The addition of lubricant could cause damage. Therefore,
do not add lubricant to either motor
bearing.
The agitator is equipped with two ball
bearings that should be lubricated periodically by a Hoover Factory Service
Center or an authorized Hoover Warranty
Service Dealer (Depot).
Service
To obtain approved HOOVER service
and genuine HOOVER parts, locate the
nearest Hoover Factory Service
Center or Authorized Hoover
Warranty Service Dealer (Depot) by:
• checking the Yellow Pages
under “Vacuum Cleaners Household” OR -
• checking the list of Factory
Service Centers provided
with this cleaner OR -
•calling 1-800-944-9200 for an
automated referral of authorized
service outlet locations (U.S. only)
OR-
•checking the Service section of The
Hoover Company online at
www.hoovercompany.com
Do not send your cleaner to The
Hoover Company in North Canton for
service, this will only result in delay.
If further assistance is needed, contact
The Hoover Company Consumer
Response Center, North Canton, Ohio
44720, Phone: 330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8, Phone:
1-800-263-6376.
Always identify your cleaner by the
complete model number when requesting information or ordering parts. (The
model number appears on the bottom
of the cleaner.)
10
Problem: Cleaner won’t run
Problem: Cleaner suction low
Problem: Agitator won’t run
Problem: Nozzle won’t pick up
Possible cause
Possible solution
• Not “ON” at cleaner.
•
Turn “ON” at cleaner.
• Not “ON” at hand grip.
•
Turn “ON at hand grip.
• Not firmly plugged in.
•
Plug unit in firmly.
• No voltage in wall plug.
•
Check fuse or breaker.
• Blown fuse or tripped breaker.
•
Replace fuse/reset breaker.
Possible cause
Possible solution
• Hose power cord not firmly
plugged in.
•
Plug firmly into receptacle on
cleaner base.
• Broken or worn belt.
•
Replace belt.
• Floor surface set to “BARE”.
•
Set floor surface to “RUG”.
Possible cause
Possible solution
• Low cleaner suction.
•
See section “Cleaner suction low”.
• Obstruction in nozzle connector.
•
Remove blockage
• Agitator not running.
•
See section “Agitator won’t run”
• Agitator brushes worn.
•
Replace brushes.
Possible cause
Possible solution
• Bag full.
•
Replace paper bag.
• Obstruction in nozzle connector,
hose or wands.
•
Remove obstruction.
• Secondary filter dirty.
•
Clean filter.
• Bag not opening.
•
Open bag by pulling folds.
• Power set too low/suction regulator
open.
•
Increase power setting/close suction
regulator.
• Hose not properly connected to
cleaner
•
Ensure hose is properly connected.
If you have a
problem
If a minor problem occurs, it usually
can be solved quite easily when the
cause is found by using the check list
below.
Full One Year
Warranty
(Domestic Use)
Your HOOVER® appliance is warranted
in normal household use, in accordance
with the Owner’s Manual against original
defects in material and workmanship for
a period of one full year from date of
purchase. This warranty provides, at no
cost to you, all labor and parts to place
this appliance in correct operating condition during the warranted period. This
warranty applies when the appliance is
purchased in the United States including its territories and possessions, or in
Canada or from a U. S. Military
Exchange. Appliances purchased elsewhere are covered by a limited one year
warranty which covers the cost of parts
only. This warranty does not apply if the
appliance is used in a commercial or
rental application.
Warranty service can only be obtained
by presenting the appliance to one of
the following authorized warranty service outlets. Proof of purchase will be
required before service is rendered.
1. Hoover Factory Service Centers.
2. Hoover Authorized Warranty
Service Dealers (Depots).
For an automated referral of authorized service outlets in the U.S.A.,
phone 1-800-944-9200 OR
visit The Hoover Company online at
www.hoovercompany.com
This warranty does not cover pick up
delivery, or house calls; however, if you
mail your appliance to a Hoover Factory
Service Center for warranty service,
transportation will be paid one way.
While this warranty gives you specific
legal rights, you may also have other
rights which vary from state to state.
If further assistance is needed, or if
there are questions concerning this warranty or the availability of warranty service outlets, write or phone the
Consumer Response Center, The
Hoover Company, 101 East Maple St.,
North Canton, Ohio 44720. Phone 1330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8,
1-800-263-6376.
HOOVER and are registered trademarks
THE HOOVER COMPANY, NORTH CANTON, OHIO 44720
R2 4-99 S3530, S3601/07/10/13/20 Litho USA 56513-345
11
Loading...