The vacuum cleaner you have just purchased is a combination cleaner. It has
a motorized power nozzle for carpet and floor cleaning and has cleaning
tools for above the floor cleaning.
Your cleaner is a model
and has a serial number
For your personal records, please enter the model number and serial number
in the spaces provided above and retain in a safe place.
The model number and serial number appear on the bottom of the cleaner.
Warning: Electric shock could occur if used outdoors or on wet surfaces.
l
Close supervision is necessary when any appliance is used by or near children.
Do not allow vacuum cleaner to be used as a toy or to run unattended at any
time.
l
Keep hands, feet, loose clothing, and hair away from rotating agitator.
l
Don’t run power nozzle over cord. It may damage insulation.
l
Do not use cleaner to pick up matches, or live ashes and cigarette butts.
o
Avoid picking up hard, sharp objects with the cleaner. They may damage
the power nozzle.
l
Unplug cleaner when not in use. Turn cleaner off at switch before
unplugging.
l
Always disconnect cord from electrical outlet before servicing the cleaner.
l
Change bag frequently when picking up very fine materials such as powder.
l
Grasp the plug to disconnect from wall outlet to avoid damage to cord,
plug, prongs, or receptacle.
l
The use of an extension cord is not recommended.
l
If cleaner is in disrepair, do not attempt to operate.
l
Have repairs made by qualified personnel at Hoover Factory Service Centers
or Authorized Hoover Warranty Service Dealers.
l
Use vacuum cleaner only for its intended use as described in the instructions.
The use of attachments not recommended by the appliance manufacturer
may cause hazards.
Save
these
instructions!
A
1. FURNITURE GUARD
2. COMBINATION CARPET AND FLOOR ‘POWERMATIC’ NOZZLE
Powermatic nozzle automatically adjusts to different carpet pile height.
Has setting for “Carpet” and “Bare Floor”.
14
I
3. SURFACE SELECTOR INDICATOR Shows “Carpet” or “Bare
Floor” setting of Surface Selector Lever.
4. SURFACE SELECTOR LEVER Push lever with your toe to adjust
the Powermatic nozzle for “Carpet” and “Bare Floors”.
5. DUSTING BRUSH
I
1
3
6. WALL/FLOOR BRUSH
7. HOSE CORD CONNECTION TO CLEANER Plug hose cord into
cleaner base to receptacle.
8. CASTERS Provide easier towing; pull cleaner using hose to guide
the cleaner easily over carpet, throw rugs, and door sills.
9. ON-OFF SWITCH A convenient switch is located near front of cleaner.
10. CORD STORAGE HOOKS
II. EXTENSION WANDS Connect to hose and Powermatic nozzle or
cleaning tools.
12. COVER LATCH
14. CREVICE TOOL
13. CARRYING HANDLE
15. FURNITURE NOZZLE
16. HANDLE ADJUSTMENT LATCH Step on the handle adjustment
latch to lower the handle.
17. CORD CLIPS Clip nozzle cord to extension wands.
18. SUCTION REGULATOR Close regulator for full suction. Open
regulator for easy cleaning of some types of carpets, lightweight
flexible rugs and lightweight draperies.
19. NOZZLE CORD CONNECTION TO HANDLE Plug nozzle cord
into receptacle underneath handle.
20. PLASTIC LATCH RING Connects hose grip to extension wand or
to cleaning tools.
21. HOSE GRIP
OPERATE CLEANER ONLY AT VOLTAGE SPECIFIED ON DATA
PLATE ON BOTTOM OF CLEANER.
WARNING: ELECTRICAL SHOCK COULD OCCUR IF USED OUT-
DOORS OR ON WET SURFACES.
4
-,
.
TO CONNECT AND REMOVE HOSE
To connect hose, insert hose into opening of cleaner
lining up the arrow on the hose with the dot on the
cleaner. Turn the hose clockwise until it lines up
with the bar on the cleaner and latch locks into
place.
When the hose is attached properly, the hose cord
plug will reach to the receptacle on the cleaner.
Insert the plug firmly and as deep into the
receptacle as possible.
To disconnect hose, depress latch away from hose
connection opening in cleaner. While holding latch,
turn the hose counterclockwise until the arrow
lines up with dot on the cleaner.
HOW TO CONNECT THE
‘POWERMATIC’ NOZZLE
1. Attach Powcrmatic nozzle to the end of the extension wand. Be sure the nozzle is locked in place.
To release, press down on the center of the white
plastic spring latch and remove nozzle.
2. Position cord in cord clips on extension wands.
3. To attach the hose and extension wands, rotate
the plastic latch ring to accept the button projection on the extension wands.
Push the handle over the wand so that the button
projection fits into the slot. Turn the outer ring on
the handle to lock the handle and wand in place.
5
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.