Hoover HW130M, HW120M, HW160M User Manual

®
Washer Dryer Instructions for use
HW120M, HW130M HW160M
05651239.qxd 17-04-02 11:38 Page 1
Contents Page
Introduction 3
Safety notes 4
Quick start 5
Installation & testing 7
Useful advice for the user 12
Description of controls 13
Detergent drawer 14
Detergents, washing aids and amounts to use 15
Programme selector 18
The main wash 19
Consumption data 22
Programme Table 23
Technical data 24
Cleaning and routine maintenance 25
Trouble shooting 27
Power failure 28
Customer service 29
2
05651239.qxd 17-04-02 11:38 Page 2
Introduction
Please read and follow these instructions carefully and operate the machine accordingly. This booklet provides important guidelines for safe installation, use, maintainance and some useful advice for best results when using your machine. Keep all documentation in a safe place for future reference or for any future owners.
3
Note: this machine is solely for domestic use, i.e. to wash, rinse and spin dry household textiles and garments.
Notes on disposal
All packaging materials used are environmentally-friendly and recyclable. Please help dispose of the packaging via environmentally-friendly means.
Your retailer or local council will be able to give you details of current means of disposal.
Appliances that have reached the end of their useful life are not worthless rubbish! Valuable materials can be salvaged from an old appliance via scrap reprocessing.
Note: to ensure safety when disposing of an old washing machine disconnect the mains plug from the socket, cut the mains power cable and destroy this together with the plug. To prevent children shutting themselves in the machine break the door hinges or the door lock.
05651239.qxd 17-04-02 11:38 Page 3
General delivery notes
Please check that the following items are delivered with the appliance:
– Instruction manual – Guarantee card – Blanking plug – Inlet hoses & bracket – Base panel – x2 push clips – x2 adhesive clips
Check that no damage has occurred to the machine during transit. If it has, call the manufactures service by GIAS (tel: 08705 400 600). Please see Customer Service.
4
Safety notes
Note: before carrying out any cleaning or maintenance of the washing machine, please read the following safety notes.
A) Disconnect the plug from the mains supply. B) Turn off the water supply. C) Hoover equips all its appliances with earthing. Ensure that the mains power
supply is earthed, if not, seek assistance from a qualified electrician.
D) Do not touch the appliance when hands or feet are wet or damp. Do not use
the appliance when bare-footed.
E) The use of adapters, multiple connectors and/or extensions is not
recommended.
F) Caution: water temperature can reach 90°C during
the whites wash cycle and as a result the door glass may get very hot.
G) Check there is no water visible in the drum before opening the door. H) Do not allow children or unauthorised persons to use the appliance without
supervision.
I) Do not pull the power cable or the appliance itself to remove the plug from the
socket.
J) The appliance must not be exposed to weather conditions (rain, direct sun,
etc...)
05651239.qxd 17-04-02 11:38 Page 4
K) When moving the appliance never lift it by the controls, the detergent drawer,
the hoses or the power cable. To avoid damaging the door when moving the appliance never rest the door against objects e.g a trolley.
L) IMPORTANT!
If the appliance is installed on a carpeted floor ensure that the ventilation
through the base of the appliance is not obstructed. M) When lifting the machine always use two people to help avoid injuries. N) If the appliance is not running properly or breaks down, switch it off, disconnect
the plug from the socket, turn off the water supply and do not tamper with the
appliance.
Consult GIAS Service (tel: 08705 400 600) for possible repair. Failure to comply
with the above can compromise the safety of the appliance. O) If the appliance’s power cable is damaged it must be replaced by a special cord
which is only available from GIAS Service. P) After the machine has been installed, ensure that the mains plug and water
supply valves are easily accessible. Q) Glass fibre curtains should never be put into this machine. R) Lint or fluff must not be allowed to collect on the floor around the outside of this
machine. S) Articles containing foam plastic, foam rubber and rubber like material MUST
NOT be placed in the machine during the tumble drying period. T) Always ensure that the door locked indicator neon has switched itself off before
opening the door. By doing so the machine is allowed to cool down before the
laundry is handled. U) Always ensure to fit the base panel to the machine.
5
Quick start
Washing
Open the door by pressing the DOOR button – Select the laundry and put it in the machine – Close the door – Put detergent in the dispenser compartments. Please refer to the programme
guide table within this manual. – Select programme by turning the programme knob. – Select any function buttons required and then press the on/off button. (The
button options are selected when the buttons are pressed in.)
Drying
This should be utilised for half load conditions (maximum 2 kg). Select the appropriate drying programme via the large programme knob ie, high heat (cottons), low heat (synthetics). Always read the wash care label on laundry to ensure that it is suitable for tumble drying.
05651239.qxd 17-04-02 11:38 Page 5
Select the drying time via the drying time dial until the required time aligns
with the indicator on the dial. – Switch on the machine by pressing the ON/OFF button. If the drying time is selected before the wash cycle is completed the machine will automatically commence the drying programme.
6
After washing – Wait about two minutes for the door locking device
to disengage. The door locked neon will go out
– Switch off the washing machine by pressing the
ON/OFF button
– Open the door and remove the laundry
05651239.qxd 17-04-02 11:38 Page 6
Remove the machine from the packaging – close to where it will finally be positioned remembering the plug must be easily accessible after installation – and proceed as follows:
On the back of the machine
1) Remove the central screw A and side screws
B and pull out the transit bracket C along
with the red locator.
2) Tilt the machine forward and remove the two
polystyrene spacers.
3) Cover the central hole using the cap
enclosed in the instructions bag.
4) Adjust the two feet at the front to level the
machine.
5) Tilt the machine forward and locatethe base
panel by (1) removing the paper backing
from the adhesive tape,(2) locate the base
panel in the front of the machine, (3) offer the
base panel up to the base of the washing
machine and locate the two push clips.
7
Installation & testing
Note: when lifting the machine always use two people to avoid injuries.
05651239.qxd 17-04-02 11:38 Page 7
Note: we recommend you keep the transit bracket and screws to protect the machine for future transit. The Manufacturers will not be responsible for any damage to the machine caused by not following the instructions relating to releasing the transit protection. The user is responsible for all installation costs.
8
Connecting the fill hoses
This machine has inlet hoses with 19mm (3/4”) threaded ferrules fitted to the ends to attach between the threaded connector on the appliance and the water supply.
Only use the new hoses supplied to connect the machine and ensure that the sealing washers are in place inside the hose connectors. Do not re-use old hoses which are attached to existing installations. Do not over-tighten the connections. Hand tight is sufficient. Do not trap or kink the hoses.
1. Connect the elbow end of hoses to
the back of the machine: red connector (for hot water) to the red threaded inlet, the white connector (for the cold water) to the white threaded inlet.
2. Connect the straight end of the
hoses to the stop taps.
Note: do not leave the packaging in the reach of children as it is a potential source of danger.
WHITE
COLD
HOT
RED
05651239.qxd 17-04-02 11:38 Page 8
If the inlet hose’s connection point is changed, check that the 3/4” threaded ferrule on the inlet hose is firmly attached to the electrovalve connector.
Water supply requirements
Connect the machine to the drainage system used by household sinks.
9
THIS MACHINE MUST BE CONNECTED IN ACCORDANCE WITH THE WATER SUPPLY REGULATIONS. WATER BYELAWS PROHIBIT CONNECTION TO A SURFACE WATER DRAIN.
No other appliance should be plumbed into the standpipe.
There are two possible arrangements which can be seen below :-
DRAIN HOSE
HOSE SUPPORT
CROOK
12-15cm
32mm
min
60-80cm
HOSE SUPPORT CROOK
ATTACH HOSE SECURELY TO
WASTE OUTLET
DRAIN HOSE
FIX SECURELY ABOVE OVERFLOW OUTLET OF SINK
For the washing machine to function properly the outlet end of the drain hose must be at a minimum of 60 cm and a maximum of 80 cm from the ground.
05651239.qxd 17-04-02 11:38 Page 9
Testing the installation
Refer to the programme guide for details of how to select programmes.
1. Turn on the water supply and check for leaks from fill hoses.
2. Switch on the electricity supply.
3. Select a spin programme and then press the on/off button to start the
machine.
Allow the programme to continue for one minute and then switch off the
machine via the on/off button. This will remove any water remaining in the
machine from factory testing.
4. To check for cold water filling to the machine:
Select a rinse programme and press the on/off button to start the machine.
Allow the tumble action to continue until the water has pumped out.
Check that the drain outlet is not leaking or overflowing.
5. Switch off the machine via the on/off button at the end of the cycle.
6. To check for hot water filling to the machine:
Select programme 1 and press the on/off button to start the machine.
Allow the wash action to continue for one minute, then switch the machine off
via the on/off button.
Alternatively, both inlets can be connected to the cold water supply by using a
suitable adaptor.
7. Select a spin programme and press the on/off button to switch the machine
on. If the machine takes longer than one minute to empty check the drain
hoses for kinks.
Installation testing is now complete.
To ensure the drum is thoroughly clean after testing and storage, select programme 1 and run the machine for a complete cycle using only wash detergent and water.
If the machine is not to be used immediately, switch off the mains power supply and remove the plug from the power socket. We also recommend that the water stop taps are turned off.
10
Note: it is advisable to isolate the washing machine from the water and electricity supplies after each wash.
05651239.qxd 17-04-02 11:38 Page 10
Loading...
+ 22 hidden pages