Hoover HSW2125, HSW2115 User Manual

®

Washer Dryer Instructions for use

HSW2115

HSW2125

40001266.qxd 15/03/2004 15:36 Page 1

Contents Page

Introduction 3

General delivery notes 4

Safety notes 4

Quick start 5

Installation & testing 7

Useful advice for the user 12

Description of controls 13

Detergent drawer 14

Detergents, washing aids and amounts to use 15

Programme selector 18

The main wash 19

Consumption data 22

Programme Table 23

Technical data 24

Cleaning and routine maintenance 25

Trouble shooting 27

Power failure 28

Customer service 29

2

40001266.qxd 15/03/2004 15:36 Page 2

Introduction

Please read and follow these instructions carefully and operate the machine
accordingly. This booklet provides important guidelines for safe installation, use,
maintainance and some useful advice for best results when using your machine.
Keep all documentation in a safe place for future reference or for any future
owners.

3

Note: this machine is solely for domestic use, i.e. to
wash, rinse and spin dry household textiles and
garments.

Notes on disposal

All packaging materials used are environmentally-friendly and recyclable. Please
help dispose of the packaging via environmentally-friendly means.

Your retailer or local council will be able to give you
details of current means of disposal.

Appliances that have reached the end of their useful life are not worthless
rubbish! Valuable materials can be salvaged from an old appliance via scrap
reprocessing.

Note: to ensure safety when disposing of an old
washing machine disconnect the mains plug from the
socket, cut the mains power cable and destroy this
together with the plug. To prevent children shutting
themselves in the machine break the door hinges or
the door lock.

40001266.qxd 15/03/2004 15:36 Page 3

General delivery notes

Please check that the following items are delivered with the appliance:

– Instruction manual
– Guarantee card
– Blanking plug
– Inlet hose & bracket
– Base panel
– x2 push clips

Check that no damage has occurred to the machine during transit. If it has, call
the manufactures service by GIAS (tel: [phone]). Please see Customer
Service.

4

Safety notes

Note: before carrying out any cleaning or maintenance
of the washing machine, please read the following
safety notes.

A) Disconnect the plug from the mains supply.
B) Turn off the water supply.
C) Hoover equips all its appliances with earthing. Ensure that the mains power

supply is earthed, if not, seek assistance from a qualified electrician.

D) Do not touch the appliance when hands or feet are wet or damp. Do not use

the appliance when bare-footed.

E) The use of adapters, multiple connectors and/or extensions is not

recommended.

F) Caution: water temperature can reach 90°C during

the whites wash cycle and as a result the door
glass may get very hot.

G) Check there is no water visible in the drum before opening the door.
H) Do not allow children or unauthorised persons to use the appliance without

supervision.

I) Do not pull the power cable or the appliance itself to remove the plug from the

socket.

J) The appliance must not be exposed to weather conditions (rain, direct sun,

etc...)

40001266.qxd 15/03/2004 15:36 Page 4

K) When moving the appliance never lift it by the controls, the detergent drawer,

the hose or the power cable.
To avoid damaging the door when moving the appliance never rest the door
against objects e.g a trolley.

L) IMPORTANT!

If the appliance is installed on a carpeted floor ensure that the ventilation

through the base of the appliance is not obstructed.
M) When lifting the machine always use two people to help avoid injuries.
N) If the appliance is not running properly or breaks down, switch it off, disconnect

the plug from the socket, turn off the water supply and do not tamper with the

appliance.

Consult GIAS Service (tel: [phone]) for possible repair. Failure to comply

with the above can compromise the safety of the appliance.
O) If the appliance’s power cable is damaged it must be replaced by a special cord

which is only available from GIAS Service.
P) After the machine has been installed, ensure that the mains plug and water

supply valves are easily accessible.
Q) Glass fibre curtains should never be put into this machine.
R) Lint or fluff must not be allowed to collect on the floor around the outside of this

machine.
S) Articles containing foam plastic, foam rubber and rubber like material MUST

NOT be placed in the machine during the tumble drying period.
T) Always ensure that the door locked indicator neon has switched itself off before

opening the door. By doing so the machine is allowed to cool down before the

laundry is handled.
U) Always ensure to fit the base panel to the machine.

5

Quick start

Washing

– Open the door by pressing the DOOR button
– Select the laundry and put it in the machine
– Close the door
– Put detergent in the dispenser compartments. Please refer to the programme

guide table within this manual.
– Select programme by turning the programme knob.
– Select any function buttons required and then press the on/off button. (The

button options are selected when the buttons are pressed in.)

Drying

This should be utilised for half load conditions (maximum 2 kg). Select the
appropriate drying programme via the large programme knob ie, high heat
(cottons), low heat (synthetics). Always read the wash care label on laundry to
ensure that it is suitable for tumble drying.

40001266.qxd 15/03/2004 15:36 Page 5

– Select the drying time via the drying time dial until the required time aligns

with the indicator on the dial.
– Switch on the machine by pressing the ON/OFF button.
If the drying time is selected before the wash cycle is completed the machine will
automatically commence the drying programme.

6

After washing
– Wait about two minutes for the door locking device

to disengage. The door locked neon will go out

– Switch off the washing machine by pressing the

ON/OFF button

– Open the door and remove the laundry

40001266.qxd 15/03/2004 15:36 Page 6

Remove the machine from the packaging – close to where it will finally be
positioned remembering the plug must be easily accessible after installation – and
proceed as follows:

On the back of the machine

1) Remove the central screw A and side screws

B and pull out the transit bracket C along

with the red locator.

2) Tilt the machine forward and remove the two

polystyrene spacers.

3) Cover the central hole using the cap

enclosed in the instructions bag.

4) Adjust the two feet at the front to level the

machine.

5) Tilt the machine forward and locatethe base

panel by (1) removing the paper backing

from the adhesive tape,(2) locate the base

panel in the front of the machine, (3) offer the

base panel up to the base of the washing

machine and locate the two push clips.

7

Installation & testing

Note: when lifting the machine always use two people
to avoid injuries.

40001266.qxd 15/03/2004 15:36 Page 7

Note: we recommend you keep the transit bracket and
screws to protect the machine for future transit.
The Manufacturers will not be responsible for any
damage to the machine caused by not following the
instructions relating to releasing the transit protection.
The user is responsible for all installation costs.

8

Connecting the Cold Fill Hose

Only one hose is required to install this machine to a cold water supply.

Cold fill is an energy efficient system. Only the water required to wash the laundry
is heated. There is no loss of heat in the pipeline from the hot water tank or the
boiler.

If your previous machine installation was hot and cold fill ensure that the hot tap is
firmly closed to prevent leakage.

Connection to the cold supply

The machine has an inlet hose with 19mm (3/4") threaded ferules fitted to the
end. This hose connects between the threaded connector on the rear of the
appliance and the water supply.

Only use the new hose supplied to connect the machine and ensure that the
sealing washers are in place inside the hose connectors.
Do not re-use an old hose which was attached to the existing installation.
Do not over-tighten the connections. Hand tight is sufficient.
Do not trap or kink the hose.

Note: do not leave the packaging in the reach of
children as it is a potential source of danger.

This Appliance must be connected to a COLD WATER
supply only

40001266.qxd 15/03/2004 15:36 Page 8

Water supply requirements

Connect the machine to the drainage system used by household sinks.

9

THIS MACHINE MUST BE CONNECTED IN
ACCORDANCE WITH THE WATER SUPPLY
REGULATIONS. WATER BYELAWS PROHIBIT
CONNECTION TO A SURFACE WATER DRAIN.

No other appliance should be plumbed into the standpipe.

There are two possible arrangements which can be seen below :-

DRAIN HOSE

HOSE SUPPORT

CROOK

12-15cm

32mm

min

60-80cm

HOSE SUPPORT CROOK

ATTACH HOSE
SECURELY TO

WASTE OUTLET

DRAIN HOSE

FIX SECURELY
ABOVE OVERFLOW
OUTLET OF SINK

For the washing machine to function properly the outlet end of the drain
hose must be at a minimum of 60 cm and a maximum of 80 cm from the
ground.

1. Connect the angled end of the hose to the

appliance

2. Connect the straight end of the hose to the Cold

water supply

40001266.qxd 15/03/2004 15:37 Page 9

Testing the installation

Refer to the programme guide for details of how to select programmes.

1. Turn on the water supply and check for leaks from the fill hose.

2. Switch on the electricity supply.

3. Select a spin programme and then press the on/off button to start the

machine.

Allow the programme to continue for one minute and then switch off the

machine via the on/off button. This will remove any water remaining in the

machine from factory testing.

4. To check for cold water filling to the machine:

Select a rinse programme and press the on/off button to start the machine.

Allow the tumble action to continue until the water has pumped out.

Check that the drain outlet is not leaking or overflowing.

5. Switch off the machine via the on/off button at the end of the cycle.

6. Select a spin programme and press the on/off button to switch the machine

on. If the machine takes longer than one minute to empty check the drain

hose for kinks.

Installation testing is now complete.

To ensure the drum is thoroughly clean after testing and storage, select
programme 1 and run the machine for a complete cycle using only wash
detergent and water.

If the machine is not to be used immediately, switch off the mains power supply
and remove the plug from the power socket. We also recommend that the water
stop taps are turned off.

10

Note: it is advisable to isolate the washing machine
from the water and electricity supplies after each wash.

40001266.qxd 15/03/2004 15:37 Page 10