Hoover HAV3460AWW, HAV2460AWW, HAV2360AWW, HAV2357AWW Owner’s Manual

HAVBB-1

Important Safety Instructions 1-2

Operating Tips

Detergent Loading

Additional Tips

.......... 3-4

Using the Controls

(Two-Speed Models) ........ 5-6

Select Water Level Select Wash/Rinse Temperature

Select Cycle

Pull Control Dial Out to Start

(Three-Speed Models) ....... 7-8

Select Water Level Select Extra Rinse

Select Wash/Rinse Temperature Select Cycle

Pull Control Dial Out to Start

(Four-Speed Models) ....... 9-10

Select Water Level Select Wash/Rinse Temperature

Select Wash/Spin Speed Select Cycle

Select Options

Pull Control Dial Out to Start

Special Features ....... 1 1-12

Liquid Bleach Dispenser Fabric Softener Dispenser

Automatic Lint Filtering Sys[em Safety Spin Unbalanced Spin Load Compensator

Overload Protector

Care & Cleaning .......... 12

Troubleshooting ........ 13-14

Service & Warranty ........ 15

Guide d'utUisation

et d'entretien ........... 16

Guia de use y cuidado ..... 32

Form No. A/07/03 Part No. 35-6811 www.maytag.com Litho U.S.A. c2003 Maytag Appliances Sales Co.

ImportnntSnfetyInstructions

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible

conditions and situations that may occur. Common sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact your dealer, distributor, service agent or

manufacturer about problems or conditions you do not understand.

Recognize Safety Symbols, Words, Labels

ImportantSafetyInstructions

1. Read ai[ [nstructbns before using the appliance.

2. As with any equipment using electricity and having moving parts, there are potential hazards. To use this 7.

appliance safely, the operator should become familiar with the instructions for operation of the appliance 8.

and always exercise care when using it.

3. Do not install or store this appliance where it will be exposed to the weather.

4. Install and level washer on a floor that can support the weight.

5. This appliance must be properly grounded. Never plug the appliance cord into a receptacle which is not grounded adequately and in accordance with local

and national codes. See installation instructions for grounding this appliance.

6. To avoid the possibility of fire or explosion: a. Do not wash items that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or

explosive substances as they give off vapors that could ignite or explode. Hand wash and line dry

any items containing these substances.

Any material on which you have used a cleaning solvent, or which is saturated with flammable

liquids or solids, should not be placed in the

washer until all traces of these liquids or solids

and their fumes have been removed.

These items include acetone, denatured alcohol,

gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes

and wax removers. Do not add gasoline, dry-cleaning solvents, or

other flammable or explosive substances to the

wash water. These substances give off vapms that

could ignite or explode.

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been

used for two weeks or more. HYDROGEN GAS iS EXPLOSIVE. if the hot water system has not been

used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each

for several minutes. This will release any

accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame

during this time.

D. Do not wash or dry items that are soiled with

vegetable or cooking oil. These items may contain

some oil after laundering. Due to the remaining oil,

the fabric may smoke or catch fire by itself.

Do not reach into the appliance if the tub or agitator is moving.

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when

the appliance is used near children and pets.

Do not tamper with controls.

10.

Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in published user-repair instructions

that you understand and have the skills to carry out.

11.

Unplug power supply cord before attempting to service your washer. Service is to be done only by

qualified service personnel.

12.

The agitator should not be removed. If the agitator is removed, it must be replaced by pushing down

completely and the locking screw tightened before the washer is operated.

13.

Keep all laundry aids such as detergents, bleach, etc., out of the reach of children, preferably in a locked

cabinet. Use laundry aids only as directed by the manufacturer. Observe all warnings on container labels.

14.

Keep the area around and underneath washer free from the accumulation of combustible materials, such as lint, paper, rags, gasoline, and all other flammable

vapors and liquids.

15.

Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remove0 in the same wash,

Hazardous fumes can form,

16.

Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in following

loads and cause skin irritation.

17.

For flame resistant finishes - follow garment manufacturer's instructions carefully. Improper laundering could remove the finish.

18.

Before the appliance is removed from service or discarded, remove the door to the washing compartment.

19.

Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically for bulges, kinks, cuts, wear or leaks and replace them every five years.

SAVE THESE INSTRUCTIONS

Operutin9Tips

Detergent

• Use either liquid or granular laundry detergent. For

best results, be sure detergent is added to the

washer BEFORE the load and be sure the wash water is above 65 ° F.

• Use the correct amount of detergent for the load size, soil level and water conditions. Use more detergent if

you have hard water and very soiled loads.

If you have soft water or a lightly soiled load, use less detergent. (See manufacturer's instructions.)

• Wipe up any detergent spills on the washer.

• Put dry, unfolded clothes loosely in the tub, up to the

top row of holes for a maximum load.

• Do not wrap large items like sheets around the agitator.

• Mix large and small items for best circulation. Wash bulky items like blankets separately.

• When laundering wrinkle free items or items of delicate construction, washable woolens or loosely knit items, never use less than the MEDIUM water level setting. This will minimize shrinkage, wrinkling

and pulling of seams.

• For best results add the detergent to the washtub before adding the load.

• Close lid carefully to avoid slamming.

Operutin9Tips

Additionam tips

, During the spin, it is possible for the load to become

unevenly distributed in the tub. If this happens, push in the control knob, open the lid, redistribute the load, close the lid and pull out the control knob. The

spin will resume at the point it was interrupted.

The washer will pause briefly throughout each cycle. These pauses are normal.

, This washer is designed so that it will not spin when

the lid is open. It will, however, fill and agitate with the lid open so water is available for pretreating

stains or diluting fabric softenen

If you open the lid during a spin cycle, the washer

will stop. When the lid is closed and the control dial

pulled out, the washer will continue the cycle at the point it was interrupted.

UsingtheControls- Two-SpeedModels

h/Rin_ [em p

Select Water Level

Determine the selected setting based on clothes load see. Selection should provide sufficient water to permit clothes to circulate freely during agitation.

It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust

the water level, turn the control to reset and then back to the desired setting.

Small 1/4 Full

Medium 1/4 - 112 Full

Large 1/2 - 3/4 Full

Oversize 3/4- Full

I Note

• Items must circulate freely for best results.

Select Wash/Rinse Temperature

Your washer gives you a choice of hot, warm or cold water for washing and cold or warm water for rinsing.

Use the chart below as a guide.

Hot/Cold

Warm/Warm Delicate items

Warm/Cold Moderately soiled, colored items;

Cold/Cold Brightly colored, lightly soiled

Note

• In wash water temperatures below 65° F, detergents do not dissolve well or clean well. Care labels define cold water as up to 85° F.

White and heavily soiled, color-fast

items

most permanent press items

items; washable woolens

Control features vary by model.

Select Cycle

To select a cycle, push the control dial IN (off position}

and turn it to the right (clockwise} until the pointer is at the soil level needed for the wash load in the

Regular, Wrinkle Free Fabrics or Delicates cycles.

Regular Fabrics Cycle

Provides normal agitation and normal spin speeds to

wash cottons and heavily soiled items. For maximum

cleaning, set the dial at Extra Heavy.

Wriak_e Free Fabrics Cycle

Provides gentle agitation and fast spin speed to protect

wrinkle free fabrics.

Dedicates Cycle

Provides slow agitation speed and slow spin speed for delicates and knits.

P ll Co tro Dia Oct to Start

You may stop the washer at any time by simply pushing the control dial IN. Therefore it is possible to obtain a non-agitated soak or to shorten, skip or repeat any part of a cycle. The control dial must be

pushed IN (off position_} when you change the setting.

Note

• Do not attempt to turn the control dial counterclockwise. Damage to the timer will result.

UsingtheControls- Three-SpeedModels

Infinite tel / !

Select Water Level

Determine the selected setting based on clothes load size. Selection should provide sufficient water to permit clothes to circulate freely during agitation.

sh/RInse Ternp

Select Wash/Rinse Temperature

Your washer gives you a choice of hot, warm or cold

water for washing and cold or warm water for rinsing.

Use the chart below as a guide.

It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust

the water level, turn the control to reset and then back to the desired setting.

Small 1/4 Full

Medium 1/4 - 112 Full

Large 1/2 - 3/4 Full

Oversize 3/4- Full

Note

• Items must circulate freely for best results.

Select Extra Rinse (if desired)

When the knob is in the "On" position, an additional

rinse at the end of the Regular, Wrinkle Free Fabrics and Delicates cycles is provided to more completely

7 remove laundry additives, suds, perfumes, etc.

Hot/Cold

Warm/Warm Delicate items

Warm/Cold Moderately soiled, colored items;

Cold/Cold Brightly colored, lightly soiled

White and heavily soiled, color-fast

items

most wrinkle-free items

items; washable woolens

Note

• In wash water temperatures below 65° F, detergents do not dissolve well or clean well. Care

labels define cold water as up to 85° F.

Control features vary by model.

Semect Cycle

To select a cycle, push the control dial WN(off position}

and turn it to the right (clockwise} until the pointer is at the soil level needed for the wash load in the

Regular, Wrinkle Free Fabrics or Delicates cycles.

Regular Fabrics Cycle

Provides normal agitation and normal spin speeds to

wash cottons and heavily soiled items. For maximum

cleaning, set the dial at Extra Heavy.

Wrinkme Free Fabrics Cyde

Provides normal agitation and slow spin speed to protect wrinkle free fabrics.

Dedicates Cycle

Provides slow agitation speed and slow spin speed for delicates and knits.

Soak Only

Provides 2 minutes of agitation and then soak. Avoid e×tended soaking - soak for 30 minetes or less.

The control dial must be manually advanced to a spin

setting to spin and drain the water.

Pull Control Dial to Start

Note

• Do not attempt to turn the control dial counterclockwise. Damage to the timer will result.

UsingtheControls- Four-SpeedModels

Select Water Level

Determine the selected setting based on clothes load size. On select models, the infinite control allows you to select a specific setting or anywhere in between.

It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust

the water level, turn the control to reset and then back to the desired setting.

Small 1/4 Full

Medium 1/4 - 1/2 Full

Large 1/2 - 3/4 Full

Oversize 3/4- Full

Note

• Items must circulate freely for best results.

Select Wash/Rinse Temperature

Your washer gives you a choice of hot, warm or cold water for washing and cold or warm water for rinsing.

Use the chart below as a guide.

Hot/Cold

Warm/Warm Delicate items

Warm/Cold Moderately soiled, colored items;

Cold/Cold Brightly colored, lightly soiled

White and heavily soiled, color-fast

items

most permanent press items

items; washable woolens

Select Wash/Spin Speed

Your washer has selectable wash and spin speed combinations.

Sturdy fabrics needing maximum

Regular water extraction like jeans, towels

Normal/Fast and bedding

Wrinkle Free Sturdy fabrics needing a slower spin Normal/Slow speed to reduce wrinkling, such as

dress shirts and dress pants

Delicate

Gentle/Slow speed because of clothing

Handwash

Ex. Gentle/Slow items

Delicate fabrics needing slower spin

construction Intermittent slow agitation and soak

to gently wash the most delicate

Note

• In wash water temperatures below 65° F, detergents do not dissolve well or clean well. Care labels define cold water as up to 85° F.

W[_nkle _Pe "_

(if desired)

Select Cyde

To select a cycle, push the control dial IN and turn it to the right (clockwise:) until the pointer is at the soil level

needed for the wash load.

Wrinkle Free Fabrics!Dedicates Cyde

Wrinkle Free Fabrics/Delicates cycles share the same

portion of the control dial. For wrinkle free fabrics, select the cycle and turn the Wash/Spin Speed dial to

Wrinkle Free Fabrics. For delicate loads select Delicates.

Regular Cycle

This cycle provides up to 16 minutes of agitation.

Select the Regular Wash/Spin Speed_

Soak Only (select models)

Provides 4 minutes of agitation, then soak. Avoid e×te_ded soaking - soak for 30 _i_utes ot Bess.

The control dial must be manually advanced to a spin

setting to spin and drain the water.

Select Options

Extra Rinse

When the knob is in the "Extra Rinse" position, an

additional rinse at the end of the Regular and Wrinkle Free Fabrics/Delicates cycles is provided to more completely remove laundry additives, suds, perfumes, etc.

Signal

The end of cycle signal will sound once the cycle is

completed. The end of cycle signal can be canceled by setting the knob to off.

If both Extra Rinse and an end of cycle signal are desired, turn the Options knob to Extra Rinse/Signal.

Pull Control Dial Out to Start

You may stop the washer at any time by simply

pushing the control dial IN. Therefore it is possible to obtain a non-agitated soak or to shorten, skip or repeat any part of a cycle. The control dial must be pushed IN (off position) when you change the setting.

Note

• Do not attempt to turn the control dial counterclockwise. Damage to the timer will result.

SpecialFeatures

Liquid Bleach Dispenser

The dispenser automatically dilutes liquid chlorine

bleach before it reaches your wash load. To use, follow

these steps:

1. Measure liquid chlorine bleach carefully, following the instructions on the bottle.

2. Add the bleach to the dispenser before adding the load. Avoid splashing or over-filling the dispenser.

Note

Never pour undiluted liquid chlorine bleach directly onto the load or into the wash tub. It is a powerful chemical and can cause fabric damage, such as tearing or color loss, if not used properly.

If you prefer to use color-safe, non-chlorine bleach, pour it into the wash tub with your

detergent. Do not pour non-chlorine bleaches into

the bleach dispenser.

Fabric Softener Dispenser

The dispenser automatically releases liquid fabric

softener at the proper time during the cycle. To use, follow these steps:

1. Pour a measured amount of fabric softener into the dispenser to fill line only.

2. If fabric softener comes below line, add warm water.

If it is necessary to clean the dispenser:

Pull the dispenser off of the top of the agitator.

Soak for one hour in sink or container in hot water and dishwashing liquid.

Hold hands over top and bottom of dispenser and shake to loosen buildup.

4. Rinse with clean, hot water. _.,_ "..

5. Repeat process if necessary.

6. Replace dispenser on agitator. _ _t _.'_

Do not use dishwashing liquid ,_:_ _j_'

inside the washer. Oversudsing ;_ ....

can occur.

' /

i!!i o \

Pour liquid chlorine bleach into

bleach dispenser.

Automatic Lint Filtering System

The Lint Filtering System does not require

cleaning.

Wash and rinse water is filtered and re-filtered

continuously to trap lint shed by most fabrics during

the agitation cycle before it can be redeposited on the wash load. The engineered hole design on the wash

basket in conjunction with water flow produced by the agitator, traps lint away from the clothes between the

inner wash basket and the outer tub. Lint is automatically flushed from the washer during the spin

cycle.

Safety Spin

If for any reason you open the washer lid when the

washer is in a spin or extract period, the operation will

immediately stop. This is for your personal safety. If

your washer does not stop, call your service technician

immediately. When the lid is closed, the operation will automatically resume.

SpecialFeatures

Unbalanced Spin Load Compensator

Your new washer is designed to handle out-of-balance

loads without shutting down or interrupting the

washing cycle.

For this reason, the cycle will always be completed. If heavier fabrics in such out-of-balance loads should

ever contain excessive moisture at the completion of

the cycle, redistribute the clothes in the washer and

reset the control dial for the final spin period.

Care&Cleaning

1. After washing, leave the lid open until the interior is dry.

2. Check hoses to be sure there are no kinks or knots.

3. Your washer should not be installed where temperatures will go below freezing, as damage to

the washer could result.

4. To clean, occasionally wipe exterior with a clean

damp sponge or cloth. Do not use polish on plastic parts.

5. Lifetime lubrication is done at the factory, so your washer never needs to be oiled or greased.

6. Do not lay heavy or sharp objects on top of your washer.

Overload Protector

A built-in protector automatically shuts off the washer

motor in case of an overload. This can occur if:

• The load being washed is too heavy.

• Too many appliances are plugged into the line operating your washer.

• A low voltage condition exists on the line.

• Lid is opened and closed repeatedly.

The overload protector permits the washer to start again when the motor has cooled to a safe operating temperature.

If the motor stops repeatedly, call your service technician.

Cleaning the Interior

The interior of the washer should be cleaned

periodically to remove dirt, soil, odor or bacteria residue that may remain in the washer as a result of

washing clothes. We recommend taking the following

steps every 60 to 120 days to clean and freshen your

washer interior. The frequency with which the washer

should be cleaned and freshened depends on factors such as usage, the amount of dirt, soil or bacteria being

run through your washer, or the use of cold water.

To clean and freshen the washer interior:

1. Add a measured amount of chlorine bleach to the bleach dispenser, following package directions.

Add 1/4 cup of detergent to the tub.

7. The top of the washer should not be used for removing stains from garments. Some stain

removers, such as rust remover, will mar the finish.

8. Remove pins, buckles or other sharp objects from clothes to prevent scratching interior parts.

9. Clothes should not be stored in washer.

10. Bleach, detergent, solvents, etc. spilled on the top of your washer that are allowed to remain will

remove the glossy finish. Remove all spills with a damp, soft cloth.

11. If you close your home for the winter, have a service

technician drain the washer. Unplug cord from

electrical outlet and disconnect hoses from faucets.

Run the washer through a complete cycle using hot water.

4. Repeat the process if necessary.

Troubleshooting

Won't Fill

Won't Agitate

Won't Spin or Drain

Load is Wet

Plug cord into live electrical outlet. Check fuse or reset circuit breaker.

Turn the control knob to proper cycle and pull knob out to start the washer. Turn both faucets on fully. Straighten inlet hoses. Disconnect hoses and clean screens. Hose filter screens may be plugged.

Check fuse or reset circuit breaker. Make sure the lid is completely closed.

Turn the control knob to proper cycle and pull knob out to start the washer. Pauses are normal. Wait and see if the washer will start again.

Check fuse or reset circuit breaker. Straighten drain hoses. Eliminate kinked hoses. If there is a home drain restriction,

call for drain service. Close lid and pull knob out to start the washer. For your safety, washer will not spin

unless the lid is closed. Suds lock - caused by too much suds. Rewash without detergent. Use correct

amount of a low-sudsing detergent. Unevenly distributed load. Redistribute the load, close the lid and pull knob out.

Check for leveling. Be sure water level is acceptable for load size. A normal spin speed is recommended for heavy loads like jeans or towels.

Stops

Leaks Water

Is Noisy

Plug cord into live electrical outlet. Check fuse or reset circuit breaker.

Close lid and pull knob out to start the washer. For your safety, washer will not spin unless lid is closed.

This may be a pause in the cycle. Wait briefly and it may start. Make sure hose connections are tight.

Make sure end of drain hose is correctly inserted and secured to drain facility. Avoid extended soaking - soak for 30 minutes or less.

Avoid overloading. Be sure washer is leveled properly as outlined in installation manual.

Weak floors can cause vibration and walking. Operating sounds will vary depending on agitation speed.

Troubleshooting

Fills with the Wrong Temperature Water

Cycle Selector Advances Through Off

• Turn both faucets on fully.

• If equipped with a temperature selector knob, be sure it is set directly on a temperature setting and not between settings.

• Make sure temperature selection is correct.

• Make sure hoses are connected to correct faucets and inlet connections. Be sure water supply is regulated correctly. Flush water line before filling washer.

• Check the water heater. It should be set to deliver a minimum 120° F (49° C) hot water at the tap. Also check water heater capacity and recovery rate.

Disconnect hoses and clean screens. Hose filter screens may be plugged. Extra Rinse (select models) is selected.

+ 33 hidden pages