Hoover F5899-910, F5899-900 Owner’s Manual

y to

Carpet r

with automatic tool conversion

IOnS On

SteamVac TMLS cleaners have 5 brushes that deep c|ea. carpets and scrub bare f|oors!

urchase!

SteamVac TMCarpet Cleaner cleans carpet fibers by applying, scrubbing and removing hot tap water and cleaning solution.

www.hoover.com

Fii| in and Retain

This HOOVER carpet cleaner is

designed for deep cleaning carpet, rugs, carpeted stairs and upholstery.

The model and serial numbers are

located on the data label on the back of the handle.

For your personal records, please enter the COMPLETE model and serial

numbers in the spaces provided and retain this information.

Your carpet cleaner is model

ENGLISH --_ pp. 1-14 ESPAI_OL _ p_g. 15-24 FRAN(;AIS _ p. 26-32

Review this manual before operating deep cleaner

Impo ant Safeguards!

and has serial number

Jt is suggested that you attach your sales receipt to this owner s manual.

Verification of date of purchase may

be required for warranty service of your Hoover product.

index

important safeguards ........... 2

Unpacking carpet cJeaner ........ 3

Assembling carpet cleaner ..... 4=5

Carpet cleaner description ....... 6

GeneraJ operation ............ 6=9

Filling the clean solution tank. 7=8 Emptying the recovery tank .. 8=9

Agitator speed selector ........ 7

Brush indicator .............. 7

How to use

Before you begin ............. 9

After cleaning ............. 9=10

Cleaning carpet ............. 10

Picking up spills ............. 10

Cleaning bare floors ....... 10-11

Using the tools .............. 11

Cleaning carpeted stairs .. 11=12

Cleaning upholstery ........ 13

if you have a problem .......... 14

Lubrication ................... 14

Service ...................... 14

Storage ...................... 14

Warranty ..................... 14

Parts & accessories mail order

form ....................... 37

®@

www.hoover.corn

When using an electrical appliance, always follow basic

READ ALL INSTRUCTIONS BEFORE USING APPLIANCE.

WARNING-"

• Use indoors only.

• Use only on surfaces moistened by the cleaning process or small spills. Do not immerse product.

• Connect to a properly grounded outlet only. See "Grounding Instructions".

• Do not clean over floor electrical outlets.

• Do not use without tanks in place.

• Use extra care when cleaning on stairs. Do not place carpet cleaner on stairs.

• Use carpet cleaner only for its intended use as described in the instructions.

• Use only attachments recommended by Hoover; others may cause hazards.

• The use of an extension cord Is not recommended, if an extension cord is

absolutely necessary, use at least a 16 gauge 3-wire cord which has a 3-prong

grounding type plug and a 3-pole receptacle that accepts the machine plug.

• Unplug carpet cleaner when not in use. Turn off all controls before unplugging.

• Unplug before connecting the powered hand tool.

• Always disconnect cord from electrical outlet before servicing the carpet cleaner.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Never handle plug or appliance with wet hands.

• Do not pull or carry by cord, use cord as a handle, close door on cord or pull

cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not use with damaged cord or plug. If appliance Is not working as it

should, has been dropped, damaged, left outdoors, or dropped Into water, take

it to a Hoover Sales and Service Center or Authorized Hoover Warranty Service

DeaJer.

• Close supervision is necessary when any appJiance is used by or near

children. Do not allow carpet cleaner to be used as a toy or to run unattended at any time.

• Do not point tools toward people or pets.

• Use only commercially available floor cleaners Intended for machine

application. Do not use any type of wax with carpet cleaner.

• To assist in reducing drying time, be certain the area Is well ventilated when using detergents and other cleaners with this machine.

• Keep detergents and other cleaners out of children's reach.

• Do not use to pick up flammable or combustible liquids such as gasoline or use In areas where they may be present.

• Do not pick up chlorine bleach, drain cleaner, gasoline or any other toxic

material with this appliance.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Avoid picking up hard, sharp objects with the carpet cleaner. They may dam=

age the machine.

• Keep hair, loose clothing, fingers, feet and all parts of body away from

openings and moving parts.

• Do not put any object Into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

• To help prevent matting and resoiling, avoid contact with carpets until they are

dry. Keep children and pets away from carpets until they are completely dry.

• Store in a dry place. Do not expose machine to freezing temperatures.

precaution, including the following:

=. shock, or injury:

Save these instructions!

Grounding

Instructions

A B

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resis-

tance for electrical current to reduce the risk of electric shock. This appliance is

equipped with a cord having an equip- ment-grounding conductor (C) and grounding plug (A). The plug must be plugged into an appropriate outlet (B) that is properly installed and grounded in

accordance with all local codes and ordinances.

Carton contents

DANGER-

Improper connection of the equipment-

grounding conductor can result in the risk of electric shock. Check with a qual-

ified electrician or service person if you are in doubt as to whether the outlet is

properly grounded. Do not modify the plug provided with the appliance - if it

will not fit the outlet, have a proper outlet

installed by a qualified electrician. This appliance is for use on a nominal 120

volt circuit and has a grounding plug that looks like the plug illustrated in

sketch (A).

A temporary adapter (D) may be used to connect this plug to a 2-pole receptacle (E) if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (B) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like (F) extending from the adapter must be connected to a perma- nent ground (G) such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian

Electrical Code.

C D

z I

Unpack carpet cleaner from the carton

and identify the parts shown. Remove and dispose of the packing.

A. Carpet cleaner B. Upper handle with powered hand tool and

scrub module

C. Bolts (2)

D. Nuts (3 =one extra included) E. Carpet/Upholstery Detergent F. Hard Floor Cleaning Solution (some models) G. Spot & Stain Spray Cleaner (some models)

H. Bare floor attachment

E F G

I. Hose holder

J. Nozzle clean=out tool (some models)

Contained in carton with hose: K. Hose

L. Stair/upholstery nozzle iVI. Hose rack and screw (taped on rack under nozzle)

Continued -_ 3

Theassembled_eanerw,__ook_ke Assemble handle

this drawing.

Attach upper hand|e

Remove clean solution tank (upper tank)

from carpet cleaner.

With cord hook (A) to back of carpet clean- er, push upper handle down onto lower

handle. Push bolts into holes on front of

handle. If bolts will not go through hole

easily handle is not pushed completely down.

Attach hose holder

Position hose holder (B) onto handle by matching tabs on rack with openings on

back of handle. Make sure holes for bolts are aligned.

Replace clean solution tank (upper tank) by positioning bottom first. Press on tank handle to snap top of tank into place.

Place nuts in recessed areas on back

of hose holder. Hold each nut in place while tightening each bolt securely

(from the front of the handle) with a Phillips screwdriver.

Only two nuts are needed on this model. The extra nut is not required but

has been provided for your conve- nience.

Press cord into cord clip on back of handle. Pull cord tight.

When handle sections are completely together, squeeze trigger (C) on upper

handle to snap trigger rod In place.

Attach tool holder

Remove tool and taped screw from holder.

Insert projections on rack into slots on back of cleaner.

Sliderackdownintoplace.Insertscrew at(D)andtightenwithaPhillipsscrew-

driver.

Position tool in holder at base of cleaner and snap it into place as shown at

arrow.

Storing hose & too|s

Store hose on holder by first positioning hose in front section of holder.

Slide bare floor attachment into holder as shown.

Continue wrapping hose under lower hook (E). Snap hose end fully into hold- er (F).

Ensure that the hose end is pushed

down completely into holder (F).

Powered hand tool

The powered hand tool is shipped in a

plastic bag for protection. Remove the bag before using the tool by first open- ing tool door.

To remove powered hand tool (G), pull it down and outward.

To reposition the tool, reverse this pro- cedure.

To remove the scrub module (H), grasp

it at the sides and pull it forward.

To reposition module, fit tabs in the stor- age area into holes on back of module.

Push module to snap it securely into position.

This is the proper storage location for the module.

How to reattach tool

COVEY

The tool cover is designed with a break- away feature which allows it to snap free

if it is pushed open too far. To reattach, align hinges of cover with

holes on sides of tool storage area.

Continued _ 5

Carpet cleaner description

The assembled carpet cleaner will look

like the drawing.

21 6

1. Hand grip

2. Solution trigger: press to release clean solution.

3. Cord clip: place cord in clip to keep it out of the way when using cleaner

4. Hose

5. Hose holder: wrap hose around holder and hooks (6) for storage.

6. Hose hooks

7. Cord hooks: wrap cord around hooks for storage. The top hook can be rotated right or left for quick and easy cord release.

8. Scrub module

9. Powered hand tool

10. Carrying handle

11. Clean solution tank handle

12. Clean solution tank cap/

measuring cup

13. Clean solution tank: holds cleaning solution.

14. Recovery tank handle: raise handle to unlock tank

for removal; lower handle for ward to lock tank into posi-

tion.

15. Recovery tank: holds dirty solution.

16. Hood

17. Brush speed selector: slide selector to set brush

speed on HI, LO, or OFR

18. Brush Indicator: spins when brushes are rotating.

19. Nozzle.

20. Cleaning mode indicator: choose either floor or tools

21. ON/OFF pedal

22. Handle release pedal: step on pedal to lower handle to operating (floor) position;

23. Stair/upholstery nozzle

24. Bare floor attachment

This carpet cleaner is intended

for household use.

Operate carpet cleaner only at voltage specified on data plate on back of cleaner.

Plug carpet cleaner Into a properly grounded outlet.

ON/OFF pedal & Handle release pedal

Step on pedal (A) to turn carpet cleaner on. Step on pedal again to turn carpet

cleaner off. Step on pedal (B) to lower handle to

operating position. Handle does not lock into a single position but "floats" to allow convenient operation.

Cleaning mode indi- cator

Indicator will show a green window next to FLOOR (C) when handle is in the operating position for cleaning carpet rugs and bare floors.

Indicator will show a green window next to TOOL (D) when handle is in the upright position for tool use on stairs upholstery etc.

carpet cleaner automatically diverts suction from FLOOR to TOOL when

handle is raised from the operating to the upright position.

To transport

To move your carpet cleaner from room to room put handle in upright and

locked position tilt carpet cleaner back on wheels and push forward.

Thecarpetcleanermayalsobeliftedby placingahandundertheupperclean

solutiontankhandleasshown.

Automatic "shut off"

When the recovery tank (lower tank) is full the automatic shutoff mechanism will shut

off the carpet cleaner suction (suction will be noticeably reduced).

At that time the red float disk will rise to the top of the recovery tank lid (E). The

carpet cleaner will no longer pick up dirty solution and the motor sound will become noticeably higher Jn pitch.

When this happens turn carpet clean- er off and empty recovery tank before continuing use.

Check clean solution tank also; it may

need to be refilled.

Brush speed selector

Your SteamVac TM carpet cleaner has three agitator brush settings.

HI = for normal cleaning of carpet and bare floors

LO =for gentle cleaning of carpets and bare floors

OFF - for cleaning carpets and bare floors when brushing is not desired.

(Such as when picking up liquid spills. See page 10.)

Slide selector button to the desired set- ting before cleaning.

Brush indicator

The brush indicator will spin (F) when the carpet cleaner is turned ON and the brushes are rotating.

If the indicator does not spin and the pattern is visible (G) when the carpet cleaner is turned ON, the brushes are not rotating.

There are three reasons why the brushes may not be rotating:

1. Brush speed selector set on OFF (see

previous section).

2. Handle in upright position (see "Cleaning mode indicator," Fig. 2-3).

3. Brush indicator screen dirty.

To clean screen (H), turn carpet cleaner off and disconnect from electrical outlet.

Remove clear cover and wipe off screen

with a damp cloth. Snap cover back into

position.

The tanks

Clean solution tank

{upper tank)

The clean solution tank holds the clean-

ing solution that is to be dispersed onto

the surface to be cleaned.

How to fill

Disconnect carpet cleaner from

electrical outlet.

Place carpet cleaner handle in the upright, locked position.

To remove tank, press down on handle

and pull forward. Carry tank to a sink.

Continued _ 7

Rotate tank cap counterclockwise and lift up to remove cap.

For heavy traffic areas: Pre-treat with HOOVER Spot &

StainSpray Cleaner*. If you do not have access to the Spot

& Stain Spray Cleaner, double the amount of HOOVER Detergent (use 2 capfuls or 10 ounces per 1 gallon tank).

5 OUNCES/

(' ')

Turn cap (A) upside down to serve as a

measuring cup.

Using cap, measure detergent following the chart below.

For carpet, carpeted stairs and uphol= stery:

Fill cap to fill line (5 ounces) with HOOVER Carpet/Upholstery Detergent.

For bare floors: Fill cap to fill line (5 ounces) with HOOVER

Hard Floor Cleaning Solution*. Do not use Hard Floor Cleaning Solution on

carpet or upholstery. Do not use any type of wax with your SteamVac TM deep cleaner.

NOTE: Use only HOOVER detergents. They are specially formulated for use with your SteamVac TM carpet cleaner.

*Available at additional cost if not included with your model.

CAUTION: Detergents contain

Anionic and Nonionic Surfactants. Avoid contact with eyes and skin. In

case of contact with eyes, flush with cold water for 15 minutes. In case of

contact with skin, wash with water. If

Irritation persists, call a physician.

Replace cap. Rotate cap clockwise

until it locks In place. Cap must be locked In place for proper perfor= mance and to prevent leaking.

Pour detergent into tank. Fill tank to

fill line (B) (1 gallon) with hot tap water.

To assure proper performance, use only

HOOVER cleaning detergent.

Position bottom of tank into unit and press on tank handle to snap tank into

place.

jjjJ.j --o

If rubber ring (C) on cap has become dislodged, reposition it with uneven side against ledge (D) as shown.

Recovery tank

{lower tank)

The recovery tank holds the dirty solu- tion that is picked up from the carpet.

When the recovery tank is full, the auto-

matic shut-off will engage (see Fig. 2-6) and the tank must be emptied.

How to empty

Turn carpet cleaner off and discon= nect from electrical outlet.

To prevent possible leaking, remove clean solution tank (Fig. 2-10) by press-

ing down on tank handle and pulling for- ward; set tank aside (do not set tank

on furniture). Step on handle release pedal (Fig. 2-2)

and lower handle until it rests on the floor.

UNLOCK

For full suction, it is important that the recovery tank lid is properly secured before cleaning.

LOCK

Raisehandletocarryingposition (straightup)tounlock tank from base of

carpet cleaner. Lift tank from carpet cleaner and carry it to a sink or drain.

Before begin

. . you

c|ean|ng

a. Vacuum thoroughly = For carpet, use a vacuum cleaner with an agitator for best results. Vacuum upholstery with a vacuum cleaner with cleaning tool

attachments. Use a crevice tool to reach into tufts and folds. Do not use the

SteamVac TM carpet cleaner as a dry

vacuum cleaner.

b. For upholstery, check cleaning code =Use your HOOVER SteamVac TM carpet

cleaner only if the upholstery fabric is marked with a "W" (for "wet" clean) or

"S/W" (for "solvent/dry" or "wet" clean). Do not clean fabric marked "S" ("sol=

vent/dry" clean only). If your upholstery does not have a code, seek professional

assistance. c. Test for colorfastness =Mix detergent

and water according to the instructions under "Fill clean solution tank", Figs. 2-8 to 2-16.

To remove tank lid, lower handle com-

pletely toward back of tank and lift off lid.

Empty the tank and reposition the lid.

Wet a white absorbent cloth withthe solution.

In a small, hidden area, gently rub the surface

with the dampened cloth. Wait ten minutes

and check for color removal or bleed with

white paper towel or cloth. If surface has

more than one color, check all colors.

d. When cleaning entire floor, move furniture out of area to be cleaned

(may not be necessary if only high traffic areas are to be cleaned). For furniture

too heavy to move, place aluminum foil

or wax paper under legs. This will pre-

vent wood finishes from staining carpet.

Pin up furniture skirts and draperies.

e. Pretreat spots and heavy traffic areas with HOOVER® Spot & Stain

Spray Cleaner*- Test Spot & Stain Spray Cleaner for colorfastness by first spray- ing it on a hidden area; wait ten minutes and blot with white paper towels or cloth. If no color change isvisible, spray Spot & Stain Spray Cleaner onto spots and traffic areas. Wait at least ten minutes. Use your SteamVacTM carpet cleaner to pick up Spot & Stain Spray Cleaner and spot. Repeat until spot is removed; carefully scrub with a household scrub brush if necessary.

Raise tank handle to carrying position to place it into base of cleaner. Move han-

dle completely forward to lock tank into place (see Fig. 2-17).

Raise handle of carpet cleaner to

upright position and reposition upper clean solution tank.

Do not saturate carpet or upholstery with PreCleaner.

If you do not have access to the Spot & Stain Spray Cleaner, double the amount of HOOVER Detergent (use 2 capfuls or 10 oz. per 1 gallon) in the

clean solution tank. No cleaning solution removes all stains from

all carpets. Stain removal varies with the type of spill, time elapsed before removal, carpet material, and carpet type.

f. To prevent staining, use plastic or alu- minum foilto protect wood or metal sur- faces from possible water spray.

g. To avoid wetting and possible damage to wood floors underneath area rug,/car- pet, either move area rugs/carpet to a non- wood bare floor surface or place waterproof material (e.g. plastic) underneath them before cleaning.

See pages 10-13 for instructions on various cleaning tasks.

*Available at additional cost if not included with your model.

After cleaning

a. Allow carpet or upholstery to dry. To help prevent matting and resoiling the

carpet, keep children and pets away from surface until it is completely dry. If

it is necessary to walk on damp car- pet, place towels or white cloths on the

traffic areas. If furniture must be replaced before the

carpet is dry, use plastic or aluminum foil pads under legs of furniture so metal

slides or wood finishes will not stain the carpet. b. If desired, the carpet may be rinsed.

Rinsing is not necessary for cleaning, but it may Improve the surface's appear-

ance after it is dry. If rinsing is desired, be careful not to

over-wet the carpet or upholstery.

Allow time for carpet or upholstery to dry completely between cleaning and

rinsing. To rinse, follow the same proce- dure for cleaning only using hot tap

water with no detergent in the upper

clean solution tank.

c. Empty tanks, rinse with clear water

and let air dry. Rinse the solution tank cap and recovery tank lid and let air dry.

d. Remove lint from filter screen located

inside recovery tank. Continued _ 9

e. If desired, vacuum thoroughly after carpet has completely dried. This will

help reduce any shading left by the car-

pet cleaner's brushes.

To clean nozzle

If lint or other debris becomes lodged in nozzle, do not attempt to remove

nozzle cover.

Pour one to two cups of clear water on a

non-carpeted floor. Do not pour water onto a wood floor.

Pick up water with your SteamVac TM carpet cleaner. Repeat as necessary

until debris is flushed out of nozzle.

Some models have a nozzle clean-out

tool for removing debris or if a non-car-

peted floor is not available. To use the tool: Disconnect carpet cleaner from

electrical outlet. Slide tool into nozzle and remove debris as shown.

To clean the outside of the machine, wipe off dirt with a cloth dampened in warm water and mild detergent. Do not

use solvent or petroleum based prod= ucts to clean the machine.

Read "Before you begin cleaning" instructions on page 9.

1. Fill clean solution tank (upper tank)

with HOOVER Carpet/Upholstery

Detergent according to instructions for Figs. 2-10 to 2-16

2. Move speed selector to LO for gen-

tle cleaning or Hi for normal cleaning.

3. Dry hands and plug cord into a prop=

erly grounded outlet. Do not clean over floor electrical out=

lets.

4. To avoid walking on damp carpet, start at the end of the room farthest from

the door or path to sink where tanks will be emptied and filled.

Step on handle release pedal and lower handle to operating position; turn carpet

cleaner ON.

5. Squeeze trigger to release cleaning solution and slowly push carpet cleaner

forward (equals one wet stroke).

6. Continue to squeeze trigger and slowly pull carpet cleaner back toward you (second wet stroke). Release trigger

and slowly push carpet cleaner forward over area just sprayed with solution (dry stroke). Then slowly pull carpet cleaner back toward you without squeezing trig- ger (dry stroke).

7. Overlap strokes by 1 inch to help pre- vent streaking.

Keep nozzle flat on floor for both for-

ward and reverse strokes.

For heavily soiled areas, repeat steps 5-

8. To avoid saturating carpet, do not use more than 4 wet strokes over one

area. Always end with dry strokes.

It is best to alternate wet and dry

strokes as described above. For best cleaning results and to aid in

faster drying of carpet, end with more dry strokes. (Continue using dry strokes

until little water is visible passing through the recovery tank lid.)

Empty recovery tank when the motor sound becomes higher pitched and

there is a loss in suction (see "Automatic shut-off", Fig 2-6)

When finished cleaning, follow "After cleaning" instructions on pages 9-10.

How to attach bare

floor attachment

Disconnect carpet cleaner from elec=

tricaJ outlet. To prevent possible leaking, remove

clean solution tank (Fig. 2-10) and

recovery tank ( Fig 2-17) before posi- tioning bare floor attachment. Set tanks aside (do not set tank on furni- ture).

1. With handle in upright position, tilt

cleaner back so that handle rests on the floor.

Your HOOVER SteamVac TM carpet cleaner may also be used to pick up

small liquid spills (1 gallon or less, never to exceed 114 inch in depth) on

carpet, upholstery, or bare floors. For best results, pick up spills immedi-

ately by placing the stair/upholstery noz- zle just above the spill and suction up

any residue on top of the carpet. If the spill remains, place either the stair/

upholstery nozzle or floor nozzle with brushes turned OFF in front of the spill,

pull the nozzle very slowly over the spill initially with suction only. Repeat with spray

and suction.

2. With foam strip (A) (located under the netting) in position as shown, place attachment on front of nozzle (B).

Make sure arrow on end of attachment points in the direction as shown.

When picking up spills on bare floors,

use only the floor nozzle with the bare floor attachment in place and speed selector in the OFF position (this will help

prevent spreading the spill).

Ifa spot is left, the stair/upholstery nozzle is generally more effective for removing it. Although no cleaning solution can com-

pletely remove all spots, they can be treat- ed by following the instructions provided

by the manufacturer of the carpet, uphol- stery, or bare floor surface being cleaned.

Do not use the SteamVac TM carpet cleaner to pick up flammable or corn= bustible liquids or chemicals.

When finished, follow "After cleaning"

instructions on pages 9-10.

3. Push attachment against nozzle while

rotating attachment downward until both ends snap into place.

(Note: Some force may be required to rotate and snap attachment intoplace.)

4. Return carpet cleaner to upright posi-

tion. Lower handle and replace recovery tank.

5. Raise handle to upright position and reposition clean solution tank.

To clean floor

Read Before you begin cleaning instructions on page 9.

Do not use the SteamVac TM carpet

cleaner on hardwood floors.

1. Fill clean solution tank with HOOVER Hard Floor Cleaning Solution (available

at additional cost if not included with your model) according to instructions for Figs.

2-10 to 2-16.

Do not use any type of wax with your SteamVac TM carpet cleaner.

2. Move speed selector to the Lo or Hi position for scrubbing or OFF if

scrubbing is not desired.

3. Dry hands and plug carpet cleaner into a properly grounded outlet.

4. Step on handle release pedal and lower handle to operating position; turn carpet cleaner ON.

5. To release solution, press trigger. Slowly move carpet cleaner forward and

backward over area to be cleaned.

6.To pick up dirty solution, release trig- ger and slowly move carpet cleaner over area where solution has just been dis- persed. Use both forward and reverse

strokes.

7. Empty recovery tank when the motor sound becomes higher pitched and there is a loss in suction (see "Automatic shut-off", Fig 2-6)

8. When finished cleaning, follow "After cleaning" instructions on pages 9-10.

Disconnect carpet cleaner from elec= trical outlet and remove attachment

from nozzle. Rinse it in clear water. Do not remove plastic screen or foam

from attachment.

A. Powered hand tool has rotating brushes for extra scrubbing action on

small carpet areas, carpeted stairs and upholstery. Brushes can be removed for

converting to the scrub module. B. Stair/upholstery nozzle has a built-

in brush to help provide the scrubbing action some spots may need for

removal. C. Scrub module with detachable

scrub pad attaches to the base of the powered hand tool (in place of brush module). Can be used to scrub stub- born areas such as scuff marks, dried spills, and in hard to reach areas on

hard surfaces.

How to attach tools

Disconnect carpet cleaner from elec =

trical outlet.

1. Place handle in upright position and remove hose from rack.

All tools attach to the hose in the same

manner:

2. Connect tool to hose by sliding it onto connector until the tab (D) locks it securely.

Using your thumb, push forward and up on the latch (E) to remove tool as

shown.

Before using tool

It may be necessary to remove air from

the system ("prime the pump") so the

clean solution will flow to the tool. Follow

these steps:

1. Attach tool to hose and turn the car- pet cleaner ON.

2. Put the tool on a hard surface or

against your hand to block off the suc-

tion.

3. Wait a few seconds (can take up to 15 seconds). Then squeeze the trigger and begin cleaning.

Follow the instructions on pages 12-13

for the appropriate cleaning task.

Attaching scrub module

1. Open the tool door and remove the powered hand tool.

2. Grasp the sides of the brush module and lift it from the base (F).

3. Pull scrub module from carpet cleaner and snap it onto the base.

Note: It may be necessary to rotate the scrub module (G) slightly so it will align

properly to the base.

*included with some models

Using the scrub tool

With a little solution, test the scrub tool on a hidden area before using on

the desired surface. If no surface change is visible, continue to use as

described below.

FOR LARGE AREAS

1. Fill clean solution tank with HOOVER Hard Floor Cleaning Solution* according

to instructions for Figs. 2-10 to 2-16.

2. Hold scrub tool above area to be cleaned and press trigger to dispense

solution.

3. Release trigger and scrub area with tool. Pick up dirty solution with

squeegee as shown. FOR SPOT CLEANING

1. Apply Hard Floor Cleaning Solution*

with the spray bottle.

2. Scrub area with tool. Pick up diry solution with squeegee as shown.

Continued -_ 11

After using scrub tool To clean scrub pad, pull it off module.

Wash it in water with mild detergent. Rinse and let air dry.

Pad must be completely dry before reat- taching to module and storing on carpet

cleaner. Replacement pads may also be pur-

chased. Ask for HOOVER part no.

40308001. To store scrub module, remove scrub

module from tool in same manner as removing the brush module.

Align openings on back of module with tabs in storage area (H).

Push module into position.

Read "Before you begin cleaning" Instructions on page 9.

1. Place handle in upright position.

Agitator brushes will not rotate while handle Is in upright position.

2. Fill clean solution tank with HOOVER Carpet/Upholstery Detergent according

to instructions for Figs. 2-10 to 2-16.

3. Attach tool to end of hose.

4. Hose length may require that machine be placed at the top of the stairs to clean upper half of stairway and at bot-

tom of stairs to clean lower half.

To prevent machine from falling, use

extra caution when cleaning on stairs.

Do not place carpet cleaner on stairs. Do not point tools toward people or

pets.

5. Dry hands and plug carpet cleaner into a properly grounded outlet.

6. Turn carpet cleaner ON. If necessary, refer to "Before using tool" section to remove air from the system.

After using tool

1. Follow steps a and b for "After clean-

ing" on page 9.

2. Rinse tool and hose by filling sink with

a small amount of water. Turn carpet cleaner ON and pickup the water

with the tool.

7. Pre-spray the carpeted stair by hold- ing the tool (A) or (B) about one inch

above the carpet and push it forward while pressing the trigger (equals one

wet stroke).

8. Positiontool against the riser and slightly press it into carpet pile. Pressthe trigger and pull the tool slowly over the carpet (second wet stroke). Release trigger at end of stroke.

3. Drain hose by turning carpet cleaner ON and holding end of hose up for sev- eral seconds. Do not press trigger.

4. Disconnect carpet cleaner from elec- trical outlet.

5. Drain solution tube (located inside hose) by pointing end of hose in sink and pressing trigger.

6. Proceed with steps c, d, and e, for "After cleaning" on page 9.

9. Lift tool, and position it against riser. Pull tool slowly over carpet without pressing trigger (dry stroke).

It is best to alternate wet and dry

strokes as described above. End with

more dry strokes to aid in faster drying

of carpet.

10. Overlap strokes by 1/2 inch to help prevent streaking.

To avoid saturating carpet, do not use more than 4 wet strokes over any one

area. Always end with dry strokes.

If additional cleaning is necessary, wait until the carpet is completely dry before using the tool again.

11. Empty recovery tank when the motor

sound becomes higher pitched and there is a loss in suction (see "Automatic shut-off", Fig. 2-6)

When finished cleaning, follow "After cleaning" instructions on page 9 and

"After using tool" instructions on page

12.

+ 28 hidden pages