Hootoo HT-WR01 User Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
HooToo.com. Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by HooToo.com, or an
endorsement of the product(s) to which this manual applies by the third-party
company in question. Regardless of any direct acknowledgement elsewhere in the
body of this document, HooToo.com hereby acknowledges that all trademarks,
registered trademarks, service marks, and other protected names and/or symbols
contained in this manual and related documents are the property of their respective
holders.

Table of Contents

INTRODUCTION ..................................................................................................... 2

PACKAGING CONTENTS ..................................................................................................... 2

SYSTEM REQUIREMENTS ................................................................................................... 2

DIAGRAM .............................................................................................................. 3

FRONT ........................................................................................................................... 3

BACK ........................................................................................... 错误！未定义书签。

INSTALLATION........................................................................................................ 3

REPEATER MODE SETUP: .................................................................................................. 4

ACCESS POINT MODE SETUP: ............................................................................................ 8

ADVANCED CONFIGURATION ............................................................................... 11

WIRELESS ..................................................................................................................... 12

LAN INTERFACE ............................................................................................................ 16

MANAGEMENT ............................................................................................................. 16

SAVE/RELOAD SETTINGS ................................................................................................. 18

REBOOT ....................................................................................................................... 18

SPECIFICATIONS ................................................................................................... 19

TECHNICAL SUPPORT ........................................................................................... 20

WARRANTY INFORMATION .................................................................................. 20

LIMITATION OF LIABILITY ................................................................................................. 20

1

Introduction

The HT-WR01 300Mbps Wireless-N WiFi Access Point and Repeater has two selectable
modes for extending the range of existing wireless networks or adding wireless
capabilities to a non-wireless network. Using a wall plug design, this allows for
convenient or hidden placement anywhere there is an available AC outlet. As a
wireless repeater, the effective range of any 802.11n WiFi network can be increased,
while still providing up to 300Mbps of data bandwidth. This WiFi signal booster can help
eliminate dead spots and provide a stronger signal in areas with obstructions that can
reduce the range of a wireless signal. The WiFi range extender is also backward
compatible with 802.11b/802.11g networks. As a wireless access point (AP), any
non-wireless router can be given wireless-N capabilities. Built in wireless security
(WEP/WPA/WPA2) will help to keep the network private. Backed by a HooToo.com
1-year warranty and free lifetime technical support.

Packaging Contents

• 1x Wireless-N Repeater

• 1x RJ45 Ethernet Cable

• 1x Instruction Manual

System Requirements

• Available AC electrical outlet

Repeater Mode:

• IEEE 802.11B or G or N compliant wireless access point (AP)

Access Point Mode:

• IEEE 802.3i/802.3u (10/100 Mbps) compliant network router

• RJ45 terminated UTP Ethernet cable

2

Diagram

Front

Power

Wireless Link/Activity

WPS

Ethernet Link/Activity

RJ45 Ethernet Port
Reset Button

3

Installation

Repeater Mode Setup:

Step 1. Connect the Repeater to an available AC electrical outlet.
Step 2. Two Options:
a. Wired Setup: Connect an RJ45 Ethernet cable from the Repeater to your computer.
(Then go to step 3)
b. Wireless Setup: Connect to the wireless network ‘WiFi-Repeater’ (then go to step 4).
Step 3. The default IP address on the Repeater is 192.168.10.1; configure your
computer to a matching network address (192.168.10.x, where ‘x’ is between 2~255)
with subnet set to 255.255.255.0 and gateway to 192.168.10.1. See below:

Windows:

1. Open control panel, open the network section.

2. Or you can right click on the windows bar and select Open network and sharing option

3. Click on Change Adapter Setting

4. Select your Ethernet card and then select properties

5. Under Networking tab find "Internet Protocol Version 4" then select properties

6. Enter the following:

IP Address: 192.168.10.X (where ‘x’ is between 2~255)
Subnet mask: 255.255.255.0
Default gateway: 192.168.10.1

Press APPLY then Ok then REBOOT your computer/laptop for the new settings to take effect.

Mac

1. Click the Apple menu located at the top left corner of the screen, then select System
Preferences.

2. On the System Preferences window, click the Network icon.

3. On the Network window, select Automatic and Built-in Ethernet on the Location and Show
drop-down fields, respectively.

4. Select Manually on the Configure IPv4 drop-down field. Enter the following:

IP Address: 192.168.10.X (where ‘x’ is between 2~255)
Subnet mask: 255.255.255.0
Router: 192.168.10.1

5. Click Apply Now to save the changes

Step 4. Open a web browser window and enter 192.168.10.1 into the address bar. This
will bring up the login prompt for the Repeater. The default user name and password

4

are ‘admin’ (without quotes).
Step 5. From the main menu on the left side of the web interface, click the ‘Setup
Wizard’ link followed by the ‘Wireless Repeater Mode (Station) option. Click ‘Next’ to
continue.

Step 6. The next screen will list some basic configuration information, so click the
‘Repeater –One Key Setting’ button to continue, followed by the ‘Wireless Network
Selection’ button.

Step 7. The next screen will display a list of detected wireless networks. Click the

‘Refresh List’ button to rescan. Select the desired wireless network and then click the
‘Next’ button.

5

Step 8. Wireless encryption settings will be automatically detected and listed on the
following screen. If the wireless network has a password, then enter this into the
‘Pre-Shared Key’ field. You should not need to change any other settings on this
screen. Click ‘Apply and Reboot’ and you will receive a confirmation prompt. Click
‘OK’ to proceed.

6