HON HAI PRECISION IND TTC509 User Manual

Installing the Touch 10

TTC5-09

The Cisco TelePresence Touch 10 can be used with a wide range of Cisco TelePresence video conferencing systems (also named codec or endpoint).

Box contents Optional

• Cisco TelePresence Touch 10 • Ethernet cable, 12.5 m

• Ethernet cable, 4.0 m * • Power injector with cables

• Cleaning cloth *

Sound bar

for audio

adjustments

The Touch screen is

adjustable to accommodate

individual ergonomic needs

Light

indicator

Connecting the cables

First connect the Ethernet cable to the Touch, then choose option A, B or C.

To a PoE injector (no PoE in wall or router)

To the endpoint

To a PoE socket (in

wall or router)

The Cisco TelePresence Touch 10 has an Ethernet port with support for PoE *.

• The LAN socket in your wall (network switch) or router can have support for PoE.

Contact your IT administrator to check if PoE is available.

• The TelePresence endpoint can have an Ethernet port with support for PoE. Check

the user documentation of your endpoint to nd if it supplies power over one of its Ethernet ports.

• If none of the above options apply use the Cisco Aironet Power Injector; which can

be ordered separately (CTS-PWR-AIR-INJ5).

First connect the Ethernet cable to the Touch device, then choose option A, B or C:

If Power over Ethernet (PoE) is supported by the endpoint, connect the

Ethernet cable from the Touch to the Ethernet (PoE) port ( TelePresence endpoint.

If Power over Ethernet (PoE) is available in the room, connect the Ethernet

cable from the Touch to the Ethernet (PoE) port in the wall/router.

If using a power injector, connect the Ethernet cable from the Touch to the

injector, and then choose one of the two options:

• Either, connect the Ethernet cable from the injector to the Ethernet

port (

• Or; connect the Ethernet cable from the injector to the Ethernet port

in the wall/router.

) on the TelePresence endpoint.

) on the

Starting up the Touch controller

Select language

Choose a language and tap Next.

Select codec to pair with

If the Touch device is connected directly to the endpoint the pairing process is run automatically in the background. Wait for 10 minutes to allow for automatic setup.

If the Touch device is connected through LAN you must select which endpoint (codec) to pair with:

Choose your endpoint from the list and tap Start Pairing or Select codec manually.

Select codec manually

The address* of the TelePresence endpoint is announced on its main screen.

Enter the IP address or hostname and tap Start Pairing.

Logging on to the endpoint

You may need to log on to the endpoint. If required, contact your system adminstrator for the username and password.

Enter the username and password and tap Ok to nish.

* When ordering the Cisco TelePresence Touch 10 as a spare part the Ethernet cable and cleaning cloth is not included.

* The PoE source (network switch) must be located in the same building as the Cisco TelePresence Touch 10. Otherwise the Cisco Aironet Power Injector must be used. The Ethernet cable (Cat5) can be up to 100 m (330 ft).

* The endpoint address: An IPv4 address may look like 192.168.0.1, an IPv6 address may look like 2001:DB8:1:0:ABCD::1, and a hostname may look like: system.name@company.com.

China RoHS Hazardous Substance Table

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

FCC Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

CanadaStatement This device complies with IndustryCanada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.

On our web site you can nd an overview of the worldwide Cisco contacts.

Go to: http://www.cisco.com/web/siteassets/contacts

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Dr.

San Jose, CA 95134 USA

Where to nd additional support and information for your Cisco TelePresence product

User documentation

For more information about Cisco TelePresence Touch 10 see the user documentation that is available on our web site:

http://www.cisco.com/en/US/products/ps11336/tsd_products_support_series_home.html

Support

For support, go to: http://www.cisco.com/support

Note This Table is a regulatory document required for products shipped to the People’s

Republic of China.

Cisco TelePresence Touch 10

INSTALLATION GUIDE

Call, share and control video meetings with a touch of a nger.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its aliates in the U.S.

and other countries. To view a list ofCiscotrademarks, go to this URL: www.cisco.com/go/trademarks. Third-

party trademarks mentioned are the property of their respective owners.The use of the word partner does

not imply a partnership relationship between Cisco and any other company. (1110R)