HON HAI PRECISION IND T77W595 User Manual

Download

COMPANY CONFIDENTIAL

3GPP Long Term Evolution Cat4

PCI Express M.2 Module

Engineering Requirements Specification

Project code: T77W595.00 Solution: MDM9625+WTR1625L SKU: WW-1-S3

- 1 -

, will update it after

Add SW section of “USB Enumeration” and “Windows

COMPANY CONFIDENTIAL

Reviewers

Review Dates

Department Name Signature

* Plan

Project Manager Choro.Chung

Project Leader Ai-ning Song

Hardware Engineer Shao-you Lin

Modification History

** Results

Rev

D0.1 2014/07/26 Ai-ning

D0.2 2014/09/11 Henry Tang

Date Originator Comment

fix hardware design

Morphing”

Initial release for carrier engagement

- 2 -

COMPANY CONFIDENTIAL

1.1

1.2

1.3

1.4

CONTENTS

GENERAL DESCRIPTION ...................................................................... 4

SYSTEM MAIN FEATURE ...................................................................... 5

SYSTEM BLOCK DIAGRAM .................................................................. 9

PIN DEFINITION ..................................................................................... 10

PLATFORM CONNECTION DESIGN ................................................. 14

HARDWARE FEATURES ..................................................................... 22

2.1 MOBILE DATA MODEM ............................................................................... 22

2.2 RF TRANSCEIVER ........................................................................................ 23

2.3 POWER MANAGEMENT IC ........................................................................ 23

2.4 ANTENNA DESIGN ....................................................................................... 24

MECHANICAL SPECIFICATIONS ...................................................... 27

3.1 OVERVIEW ..................................................................................................... 27

3.2 MECHANICAL CONSTRAINTS .................................................................. 27

3.3 M.2 CARD ASSEMBLY ................................................................................ 28

ELECTRICAL SPECIFICATIONS ........................................................ 30

4.1 RECOMMENDED OPERATING CONDITIONS ....................................... 30

4.2 POWER CONSUMPTION ............................................................................. 30

RF PERFORMANCE SPECIFICATIONS ........................................... 31

5.1 RF MAXIMUM TX POWER SPECIFICATIONS........................................ 31

5.2 RF MIN. RX SENSITIVITY SPECIFICATIONS ......................................... 32

- 3 -

COMPANY CONFIDENTIAL

1. General Description

T77W595.00 is designed to enable wireless data connectivity for notebook computer or any

other device compatible with the PCI Express M.2 Specification 3042 type slot. T77W595.00

is the data card solution that delivers wireless wide-area network (WWAN) connectivity for

the LTE, UMTS (HSDPA/HSUPA/HSPA+/DC-HSPA+), CDMA 1xRTT/ EV-DOr0/ EV-DOrA /

EV-DOrB, GPRS/EDGE and GPS/Glonass protocols in one hardware configuration.

SKU WW-1-S0

WTR1605L

QUAD BAND BC 0,1,10 Band 1,2,4, 5,8

TX_LB1 BC0,BC10 TX_LB2 850,900 TX_LB3 B12/B17 TX_LB4 B13 TX_MB1 TX_MB2 1800,1900 TX_MB3 BC1 B1,B2 B2/B25,B1 TX_MB4 B4 B3,B4 TX_HB1 B7 TX_HB2 PRX_LB1 B13 PRX_LB2 900 B8 B8,B20 PRX_LB3 850 BC0,BC10 PRX_LB4 B12/B17,B28 PRX_MB1 BC1 B2 B2/B25 PRX_MB2 1800,1900 PRX_MB3 B3 PRX_HMB4 B1,B4 B1,B4 PRX_HB1 PRX_HB2 PRX_HB3 B7 DRX_LB1 B8 B8 DRX_LB2 B20 DRX_LB3 BC0,BC10 DRX_LB4 B12/B17,B13,B28 DRX_MB1 BC1 B2 B2/25 DRX_MB2 DRX_MB3 B3 DRX_HMB4 B1,B4 B1,B4 DRX_HB1 DRX_HB2 DRX_HB3 B7 GNSS

G C W L

Band 1,2,3,4,5,

7,8,12,13,17,20,25,26,28

B5,B8 B26/B5,B8,B20,B28

B5 B5/B26

Approximately

All

All CDMA 1X/CDMA EVDO

All

COMPANY CONFIDENTIAL

1.1 System Main Feature

Feature Description Physical PCI express M.2 module, size 3042, 75Pin golden finger Electrical Single VCC supply (3.135V~4.4V follow M.2 standard)

Dimension

Shielding design

Weight

Dimensions (L × W × H): 42 mm × 30 mm × 2.3 mm, maximum height=2.38mm (add PCB tolerance=0.08mm) Shield case on board design, no additional shielding requirement

6.2g

USIM Off-board USIM connector supported

WCDMA/HSDPA/HSUPA/HSPA+ operating bands:

Band 1: 1920 to 1980 MHz (UL), 2110 to 2170 MHz (DL) Band 2: 1850 to 1910 MHz (UL), 1930 to 1990 MHz (DL)

Band 4: 1710 to 1755 MHz (UL), 2110 to 2155 MHz (DL) Band 5: 824 to 849 MHz (UL), 869 to 894 MHz (DL) Band 8: 880 to 915 MHz (UL), 925 to 960 MHz (DL) GSM operating bands:

GSM850: 824 to 849 MHz (UL), 869 to 894 MHz (DL)

E-GSM900: 880 to 915 MHz (UL), 925 to 960 MHz (DL)

DCS1800: 1710 to 1785 MHz (UL), 1805 to 1880 MHz (DL)

PCS1900: 1850 to 1910 MHz (UL), 1930 to 1990 MHz (DL) LTE FDD operating bands: Band 1: 1920 to 1980 MHz (UL), 2110 to 2170 MHz (DL) Band 2: 1850 to 1910 MHz (UL), 1930 to 1990 MHz (DL) Band 3: 1710 to 1785 MHz (UL), 1805 to 1880 MHz (DL)

Operating Bands

Band 4: 1710 to 1755 MHz (UL), 2110 to 2155 MHz (DL)

Band 5: 824 to 849 MHz (UL), 869 to 894 MHz (DL)

Band 7: 2500 to 2570 MHz (UL), 2620 to 2690 MHz (DL)

Band 8: 880 to 915 MHz (UL), 925 to 960 MHz (DL)

Band 12: 699 to 716 MHz (UL), 729 to 746 MHz (DL)

Band 13: 777 to 787 MHz (UL), 746 to 756 MHz (DL)

Band 17: 704 to 716 MHz (UL), 734 to 746 MHz (DL)

Band 20: 832 to 862 MHz (UL), 791 to 821 MHz (DL)

Band 25: 1850 to 1915 MHz (UL), 1930 to 1995 MHz (DL)

Band 26: 814 to 849 MHz (UL), 859 to 894 MHz (DL)

Band 28: 703 to 748 MHz (UL), 758 to 803 MHz (DL) CDMA 1X/CDMA EV-DOrB operating bands:

BC0: 824 to 849 MHz (UL), 869 to 894 MHz (DL)

BC1: 1850 to 1910 MHz (UL), 1930 to 1990 MHz (DL)

BC10: sub-band class 2&3, 816 to 824 MHz (UL),

861 to 869 MHz (DL)

WCDMA/HSDPA/HSUPA/HSPA+ operating bands

Diversity/2nd Rx

operating bands

LTE operating bands

GNSS

GPS: L1 (1575.42MHz) GLONASS: L1 (1602MHz)

Antenna connectors

COMPANY CONFIDENTIAL

USIM Voltage Support 1.8V and 2.85V, and auto detects follow SIM card type

MAIN and AUX(supports Diversity and GPS simultaneously)

GPRS: DL 85.6 kbps /UL 85.6 kbps EDGE: DL 236.8 kbps/UL 236.8 kbps WCDMA CS: DL 64 kbps /UL 64 kbps WCDMA PS: DL 384 kbps /UL 384 kbps

Throughput

HSPA+: DL 21.6 Mbps /UL 5.76 Mbps DC-HSPA+ :DL 42 Mbps/UL 5.76 Mbps CDMA 1x: DL 153.6 kbps/UL 153.6 kbps EVDO Rev.A: DL 3.1 Mbps /UL 1.8 Mbps EVDO Rev.B: DL 14.7 Mbps/UL 5.4 Mbps LTE FDD：DL:150 Mbps/UL 50 Mbps @20M BW cat4

LTE air interface

LTE R10, Cat4, 20MHz BW (FDD: up to 150 Mbps downlink, 50 Mbps uplink)

 FDD: up to 150 Mbps downlink, 50 Mbps uplink

 1.4 to 20 MHz RF bandwidth

 1X2 MISO (1Tx and 2Rx for two downlinks simultaneously)

 IPv6, QoS

WCDMA/HSPA air interface

 R99:

All modes and data rates for WCDMA FDD

 R5 HSDPA

PS data speeds up to 7.2 Mbps on the downlink

 R6 HSUPA

E-DCH data rates of up to 5.76 Mbps for 2 ms TTI (UE category 6) uplink

 R7 HSPA+

Downlink 64 QAM; up to 21 Mbps

1X2 MISO (1Tx and 2Rx for two downlinks simultaneously)

2Rx with 16 QAM; up to 28 Mbps

Uplink 16 QAM; up to 5.76 Mbps

 R8 DC-HSPA+

Downlink dual carrier with 64 QAM; up to 42 Mbps

CDMA air interface

 1xRTT

COMPANY CONFIDENTIAL

153.6 kbps forward link, 153.6 kbps reverse link

 1xEV-DOr0

High-speed peak data rates – 2.4 Mbps forward link; 153 kbps reverse link

 1xEV-DOrA

High-speed peak data rates – 3.1 Mbps forward link; 1.8 Mbps reverse link

 1xEV-DOrB

High-speed peak data rates – 14.7 Mbps forward link; 5.4 Mbps reverse link

GSM / GPRS / EDGE air interface

 R99

Circuit-switched data: 9.6 k; 14.4 k

 GPRS

Packet-switched data:

DTM (simple class A) operation

Multi-slot class 12 data services

CS schemes – CS1, CS2, CS3, and CS4

GEA1, GEA2, and GEA3 ciphering

Maximum of four Rx timeslots per frame

 EDGE



E2 power class for 8 PSK

DTM (simple class A), multislot class 12

Downlink coding schemes – CS 1-4, MCS 1-9

Uplink coding schemes – CS 1-4, MCS 1-9

BEP reporting

SRB loopback and test mode B

8-bit and 11-bit RACH

PBCCH support

One-phase/two-phase access procedures

Link adaptation and IR

NACC, extended UL TBF

GNSS

 GPS

Standalone, MS-A, MS-B, and XTRA GPS

 Glonass

GLONASS standalone mode

GLONASS capability increases the number of satellites available to the positioning

COMPANY CONFIDENTIAL

engine, resulting in an expanded area of coverage over traditional GPS receivers

COMPANY CONFIDENTIAL

1.2 System Block Diagram

Figure 1-1 System block diagram

Chipsets: MDM9625+WTR1625L+PM8019+QFE1101

COMPANY CONFIDENTIAL

1.3 Pin definition

1.3.1 Golden finger Pin sequence

Figure 1-2 shows the sequence of pins on the 75-pin signal interface of M.2 3042.

1.3.2 Pin definition

Table 1-1 M.2 Pin definition

No. M.2 Pin name I/O Description Platform

connection 1 CONFIG_3 O Connected to Ground internally. 2 3.3V PI Power supply (3.1V-4.4V) 3 GND PI Ground 4 3.3V PI Power supply (3.3V+/-5%) 5 GND PI Ground 6 Full_Card_Power_Off

(0/1.8V or 0/3.3V)

I When it is Low, M.2 card powers

off. When it is High, M.2 card powers on. Pull down on card, should be tolerant of 3.3V

7 USB_D+ IO USB Data+ defined in the USB

2.0 Specification.

8 W_DISABLE#1

(0/3.3V)

I Active low signal used by the host

COMPANY CONFIDENTIAL

to turn on/off radio operation. When it is Low, radio off. When it is High, radio on.

9 USB_D- IO USB Data- defined in the USB 2.0

Specification.

10 LED#1 O Active low signal, used to allow

the M.2 card to provide status indicators via LED devices that

will be provided by the system. 11 GND PI Ground 12~19 Notch - Notch 20 AUDIO_0 - Don’t need to connect to platform;

Connect to MDM9xxx

PRIM_PCM_CLK 21 CONFIG_0 O Not connect internally.

22 AUDIO_1 - Don’t need to connect to platform;

Connect to MDM9xxx

PRIM_PCM_SYNC 23 WoWWAN (0/1.8V) O WWAN to wake up the host, It is

active low. 24 AUDIO_2 - Don’t need to connect to platform;

Connect to MDM9xxx

PRIM_PCM_DIN 25 DPR (0/1.8V) I Hardware pin for BodySAR

Detection

H: No TX power backoff (default)

L: TX power backoff 26 W_DISABLE#2 I GPS disable:

H:Turn on GPS/GLONASS

(default)

L: Turn off GPS/GLONASS 27 GND PI Ground 28 AUDIO_3 - Don’t need to connect to platform;

Connect to MDM9xxx

PRIM_PCM_DOUT 29 SSIC-TxN - Don’t need to connect to platform;

Connect to MDM9xxx SPI_MOSI 30 UIM-RESET O UIM-RESET 31 SSIC-TxP - Don’t need to connect to platform;

Connect to MDM9xxx SPI_MISO 32 UIM-CLK O UIM-CLK 33 GND PI Ground 34 UIM-DATA IO UIM-DATA 35 SSIC-RxN - Don’t need to connect to platform;

Connect to MDM9xxx SPI_CS_N 36 UIM-PWR O UIM-PWR

COMPANY CONFIDENTIAL

37 SSIC-RxP - Don’t need to connect to platform;

Connect to MDM9xxx SPI_CLK 38 N/C - Don’t need to connect to platform;

Connect to MDM9xxx

USB_HS_ID 39 GND PI Ground 40 GNSS_SCL (0/1.8V*) IO I2C_CLK, Don’t need to connect

to platform 41 NC - Don’t need to connect to platform;

Connect to MDM9xxx

UART_CTS_N 42 GNSS_SDA

(0/1.8V*)

IO I2C_DATA, Don’t need to connect

to platform 43 NC - Don’t need to connect to platform;

Connect to MDM9xxx

UART_RFR_N 44 GNSS_IRQ (0/1.8V*) IO I2C_IRQ, Don’t need to connect

to platform 45 GND PI Ground 46 SYSCLK (0/1.8V*) O Don’t need to connect to platform;

Connect to PMIC XO 47 NC - Don’t need to connect to platform;

Connect to MDM9xxx

MDM_UART_TX 48 TX_BLANKING I Don’t need to connect to platform; 49 NC - Don’t need to connect to platform;

Connect to MDM9xxx

MDM_UART_RX 50 NC - Not connect 51 GND PI Ground 52 Reserve - MDM_WLAN_SD2_D1 53 Reserve - MDM_WLAN_SD2_D3 54 Reserve - MDM_WLAN_SD2_D0 55 Reserve - MDM_WLAN_SD2_D2 56 Reserve - MDM_WLAN_SD2_CLK 57 GND PI Ground 58 Reserve - MDM_WLAN_SD2_CMD 59 ANTCTL0 (0/1.8V) O Tunable antenna control signal,

bit 0 60 COEX3 (0/1.8V) IO For LTE/WLAN co-existence;

LTE_WLAN_PRIORITY 61 ANTCTL1 (0/1.8V) O Tunable antenna control signal,

bit 1 62 COEX2 (0/1.8V) IO For LTE/WLAN co-existence;

LTE_FRAME_SYNC 63 ANTCTL2 (0/1.8V) O Tunable antenna control signal,

bit 2 64 COEX1 (0/1.8V) IO For LTE/WLAN co-existence;

COMPANY CONFIDENTIAL

LTE_ACTIVE 65 ANTCTL3 (0/1.8V) O Tunable antenna control signal,

bit 3 66 SIM Detect I SIM_SWP 67 Reset# (0/1.8V) I System reset 68 SUSCLK(32kHz)

- Reserve

(0/3.3V) 69 CONFIG_1 O Connected to Ground internally. 70 3.3Vaux PI Power supply (3.3V+/-5%) 71 GND PI Ground 72 3.3Vaux PI Power supply (3.3V+/-5%) 73 GND PI Ground 74 3.3Vaux PI Power supply (3.3V+/-5%) 75 CONFIG_2 O Connected to Ground internally.

COMPANY CONFIDENTIAL

1.4 Platform connection design

1.4.1 Configuration Pins

The M.2 module provides 4 configuration pins. T77W595 is configured as WWAN-SSIC 0,

refer to PCIe M.2_Rev 1.0.

Item Module configuration decodes Module type Port configuration

Config Config_0 Config_1 Config_2 Config_3

21 69 75 1

WWAN-SSIC

0 Pin No.

State NC GND GND GND

1.4.2 Power and ground

(1) Power Rail Parameters Parameter Min Type Max Units

Operating voltage 3.135

3.3 4.4 Vdc

The operating voltage was defined in PCIe M.2_Rev 1.0 standard as 3.135V~4.4V.

(2) 3.135 V is the minimum voltage supplied to LTE M.2 card by the host platform, and VCC

must never be under 3.135 V in any case. As our experiment, if we set the VCC=3.0V, the

M.2 card will power off when M.2 card working at +23dBm continue mode.

(3) Whenever the M.2 module works at 2G mode, the module transmits at the maximum

power (like +33dBm), the transient peak current may reach to 2.5 A.

We recommended design the VCC supply of host as below:

Remark: When the system power restarts, reserve R1 to discharge power.

(4) The LTE M.2 module provides 5 power pins and 11 Ground pins. To ensure that the LTE

module works normally, all the pins must be connected.

COMPANY CONFIDENTIAL

1.4.3 Full_Card_Power_Off

The M.2 LTE module can be controlled to power on/off by the Full_Card_Power_Of pin. Item State M.2 card state

1 Low Powers off, It’s internally pulled down by 100K ohm resistor 2 High Powers on, it is 3.3V tolerant but can be driven by either 1.8V or

3.3V GPIO.

The recommended connections as below

1.4.4 USB interface

T77W595 module is compliant with USB2.0 in all three modes (Low speed, Full speed, and

high speed). When two devices are connected via a USB interface, one of the devices must

act as a host, and the other device must act as a peripheral. The host is responsible for

initiating and controlling traffic on the bus.

Figure 1-4-4 USB2.0 interface

COMPANY CONFIDENTIAL

1.4.5 W_DISABLE#

This control setting is implementation-specific and represents the collective intention of the

host software to manage radio operation. T77W595 provides a hardware pin (W_DISABLE#)

to disable or enable the radio. Besides, the radio can also be enabled or disabled through

software AT commands.

Item State Function (WWAN state) W_DISABLE#1 Low WWAN Disabled (no RF operation allowed)

High WWAN Enabled (RF operation allowed), internally pull up

W_DISABLE#2 Low GPS Disabled (no RF operation allowed)

High GPS Enabled (RF operation allowed), internally pull up

1.4.6 LED Indication

The LED signal is provided to enable wireless communication add-in cards to provide status

indications to users via system provided indicators

(1) State of the LED# pin Item State Definition Interpretation

1 Low The LED is emitting light. Radio is capable of transmitting. 2 High The LED is emitting no light. Radio is incapable of transmitting.

(2) Typical LED Connection in Platform/System

COMPANY CONFIDENTIAL

1.4.7 WoWWAN

The WAKE_ON_WWAN# signal is for power saving.

•LTE module always listening at very low power in idle mode

•LTE module will wake up mother board via ‘WoWWAN’ signal.

•The platform will power on when triggered by the LTE module.

The WAKE_ON_WWAN# signal is used to wake up the host. It is open drain and should be

pulled up at the host side. When the WWAN needs to wake up the host, it will output a one

second low pulse, shown in Figure 1-4-6.

Typical Connection in Platform/System

COMPANY CONFIDENTIAL

1.4.8 DPR (Dynamic Power Reduction)

The optional DPR signal is used by wireless devices to assist in meeting regulatory SAR

(Specific Absorption Rate) requirements for RF exposure. The signal is provided by a host

system proximity sensor to the wireless device to provide an input trigger causing a

reduction in the radio transmit output power.

The required value of the power reduction will vary between different host systems and is

left to the host platform OEM and card vendor to determine, along with the specific

implementation details. The assertion and de-assertion of DPR is asynchronous to any

system clock. All transients resulting from the proximity sensor need to be de-bounced by

system circuitry.

(1) State of the DPR Item State Definition Interpretation

1 Low 2 High

Enable the SAR power back off. Disable the SAR power back off,

internally pull up

Radio is capable of transmitting. Radio is incapable of transmitting.

(2) Typical Connection in Platform/System

Remark:

a. The proximity sensor was controlled by the platform side.

After DPR pin becomes low level, you can set the MAX TX power by AT commands..

COMPANY CONFIDENTIAL

1.4.9 USIM

The UIM contains parameters necessary for the WWAN device’s operation in a wireless

wide area network radio environment. The UIM signals are described in the following

paragraphs for M.2 add-in cards that support the off-card UIM interface.

(1) USIM card socket

It is recommended to take electrostatic discharge (ESD) protection measures near the USIM

card socket. The USIM socket should be placed near the NGFF interface (<100 mm),

because a long circuit may impact signal quality.

(2) UIM-PWR

UIM_PWR power supply can supply 1.8 V and 2.85 V power to UIM card and auto detects

follow SIM card type

(3) SIM Detect

This signal is used to detect the insertion and removal of a SIM device in the SIM socket.

With a Normal Short SIM Card connector, PUSH-PUSH type, the detect switch is normally

shorted to ground when no SIM card is inserted. When the SIM is inserted, the

SIM_DETECT will transition from logic 0 to logic 1 state. The rising edge will indicate

insertion of the SIM card. When the SIM is pulled out, the SIM_DETECT will transition from

logic1 to logic 0. This falling edge will indicates the pulling out of the SIM card. The M.2

module monitoring this signal will treat the rising/falling edge or the actual logic state as an

interrupt, that when triggered, the module will act accordingly.

COMPANY CONFIDENTIAL

1.4.10 Antenna Control

T77W595 provides GPIO control signals for external antenna tuner application. The function

is under development for customization. ANTCTRL (0-3) are provided to allow for the

implementation of antenna tuning solutions. The number antenna control lines required will

depend on the application and antenna/band requirements.

Foxconn general design for WWAN module with two control signals.

ANTCTL0 ANTCTL1 Frequency (MHz) Band support 0 0 880 ~ 960 Band8 (WCDMA) + GSM900 + High Bands 0 1 791 ~ 894 Band5 (WCDMA, LTE) + GSM850 + High Bands 1 0 746 ~787 Band13 (LTE) + High Bands 1 1 704 ~746 Band17 (LTE) + High Bands

1.4.11 Coexistence

COEX1, COEX2 and COEX3 are provided to allow for the implementation of wireless

coexistence solutions between the radio(s) on the M.2 Card and other off-card radio(s).

These other radios can be located on another M.2 Card located in the same host platform or

as alternate radio implementations (for example, using a PCI Express M.2 CEM or a

proprietary form-factor add-in solution).

Reserve for future extension, please contact with us if need to use these Pins. Item Signal name GPIO from MDM9x15 Description

COEX1 LTE_ACTIVE COEX2 LTE_FRAME_SYNC COEX3 LTE_WLAN_PRIORITY

GPIO_51 GPIO_52 GPIO_53

TBD TBD TBD

COMPANY CONFIDENTIAL

1.4.12 RESET#

Asynchronous RESET# pin, active low. Whenever this pin is active, the modem will

immediately be placed in a Power On reset condition. Care should be taken not to activate

this pin unless there is a critical failure and all other methods of regaining control and/or

communication with the WWAN sub-system have failed.

The Reset# signal is relatively sensitive, it is recommended to install one capacitor

(10~100pF) near to the M.2 card pin.

COMPANY CONFIDENTIAL

2. Hardware features

T77W595.00 consists of the following key engine components, in addition to the required

front-end RF and other discrete components.

Modem engine

■ Soft Baseband: MDM-9625

■ RF: WTR1625L

■ Power: PM8019

Connectivity engine

■ USB: USB2.0 high-speed

■ USIM: located off board

■ Antenna: connectors for the off board antennas

2.1 Mobile Data Modem

The MDM9625 chipset solution integrates powerful digital signal processors (DXPs) into any

market-proven wireless modem, offering increased processing capacity and lower power

consumption. They are complete system solutions that operate on networks worldwide. The

major functions of MDM9625 used on T77W595.00 are listed below:

❒ Processor:

- Manufactured in 28nm CMOS process

- System uP (Cortex-A5 + L2 cache at up to 1 GHz)

❒ Memory:

- External memory (16KB for security)

EBI1: 1Gb LPDDR1

- External memory

EBI2: 2Gb NAND flash

❒ Air interface:

- WCDMA (R99, HSDPA, HSUPA, HSPA+, DC-HSPA+)

- CDMA (1x, EV-DOr0, EV-DOrA, EV-DOrB)

- LTE (R10 Cat4, FDD/TDD)

- GSM (GSM R99, GPRS, EDGE)

- GPS/Glonass

❒ Advance RX operation:

- Mobile receive diversity (WCDMA, CDMA and LTE)

COMPANY CONFIDENTIAL

❒ Connectivity:

- USB 2.0 HS with built-in USB PHY

- UART interface

- UIM support (dual voltage)

2.2 RF transceiver

The WTR1625L device is a highly integrated and versatile RF CMOS transceiver IC that can

be used in multimode, multiband applications – including Rx diversity. The WTR1605 IC is

the RF transceiver IC within compatible Qualcomm MDM9625 chipsets.

The WTR1625 IC integrates advanced receive and transmit features into a 5.47 × 5.47 ×

0.63 mm package to simplify handset design, minimize parts count, and reduce DC power

consumption. These advanced Rx/Tx features include:

 Multimode, multiband RF transceiver functions:

 GNSS receiver functions

 Fully integrated LO generation and distribution circuits to support all the RF operating

band and mode combinations

 Primary, diversity, and GNSS receivers that can operate simultaneously

 Tx power detector for monitoring the transmit power levels

 The GSM receiver can share the secondary paths with CDMA, WCDMA, and LTE

diversity receivers

 Qualcomm’s intelligent receiver technology for CDMA modes:

 Low operating voltages that help save battery current and allows the WTR IC power to

be supplied by the PMIC’s switching mode power supply (SMPS) circuits for even

greater power savings

2.3 Power management IC

T77W595.00 system uses the Qualcomm PM8019. Qualcomm has worked with Maxim

Integrated Products Inc. to develop a custom PMIC solution for use with the T77W595.00

platform.

COMPANY CONFIDENTIAL

2.4 Antenna Design

2.4.1 Antenna specification

T77W595.00 also provides connectivity for off board antennas. The antennas and their

connection interface for this device satisfy the requirements specified in the PCI Express

M.2 Specification Revision Version 1.0 standard. The antenna elements are typically

integrated into the notebook/ultrabook /tablet and connected to T77W595.00 module via

flexible RF coaxial cables. T77W595.00 provides two RF connectors (MHF type), one for

the primary transmitter/receiver port and the other for the diversity receiver and GNSS.

To ensure stable RF performance, customer must assemble adequate antenna according to

the antenna specification.

Table 2-1 Main antenna specifications

Parameter Min. Typ. Max. Units Notes Cable loss / / 0.5 dB Maximum loss to antenna

Impedance / 50 / Ohm Antenna load impedance

VSWR / / 3:1 / Maximum allowed VSWR of antenna

Table 2-2 Aux antenna specifications

Parameter Gain Maximum gain and uniform converge in high angle elevation

and zenith. Gain in the azimuth is not desired. Average 3D gain >-5dBi VSWR Typical value <3:1

Isolation(diversity to Main)

>10dB in all related bands Polarization Any

2.4.2 Antenna location and mechanical design.

To ensure customer has a clear knowledge of the two antennas, check below product

picture.

Figure 2-1 Antenna connector location and type

Figure 2-2 RF connectors

COMPANY CONFIDENTIAL

Figure 2-3 RF receptacles

COMPANY CONFIDENTIAL

3. Mechanical Specifications

3.1 Overview

T77W595.00 is compatible with the PCI Express M.2 Specification 3042 type 75-pin card

edge-type connector. Refer to Electromechanical Specification Revision 0.7a, Version 1.0

with Input Power and Voltage Tolerance ECN for more details.

3.2 Mechanical constraints

Figure 3-1 shows the mechanical constraints of T77W595.00 (3042-S3-B)

COMPANY CONFIDENTIAL

3.3 M.2 card assembly

Figure 3-2 shows Stack-up Mid-Line (In-line) Single Sided Module for 1.5 Maximum

Component Height, refer to section 2.4.8.3.1 of PCIe M.2_Rev 1.0 standard.

Remark:

a. 2.4mm maximum above mother board

b. Cut area of main board under M.2 module

c. Need to add thermal pad between M.2 module and mechanical component (like material

shielding) for thermal dissipation.

COMPANY CONFIDENTIAL

3.4 Connector assembly

a. Mate the connector vertically as much as possible. Adjusting the mating axis of plug

and receptacle. Do not slant mate.

b. Unmating: In case of unmating by pulling tool. Use the pulling tool as the following

drawing, and pull plug to vertical direction as directly as possible

c. Pulling tool(Unit:mm)

COMPANY CONFIDENTIAL

4. Electrical Specifications

4.1 Recommended operating conditions

Table 4-1 Recommended operating conditions Parameter Min Type Max Units

Storage temperature -30 +25 +85 °C Recommend operating temperature (3GPP compliant) Extend operating temperature (operational, non-3GPP compliant) Operating voltage 3.135

Operating T77W595.00 device under conditions beyond its absolute maximum ratings

(Table 4-1) may damage the device. Absolute maximum ratings are limiting values to be

-10 +25 +60 °C

-20 +25 +70 °C

3.3 4.4 Vdc

considered individually when all other parameters are within their specified operating ranges.

Functional operation and specification compliance under any absolute maximum condition,

or after exposure to any of these conditions, is not guaranteed or implied. Exposure may

affect device reliability

4.2 Power consumption

Table 4-2 Radio system power consumption

Test condition

Sample

Test

Estimated power

range goal

(Typical)

Estimated power

range goal

(Max.)

GSM in suspend mode TBD <5mA

GSM (Tx=33dBm single slot) TBD

WCDMA in suspend mode TBD

WCDMA (Tx=24dBm) TBD

CDMA in suspend mode TBD

CDMA (Tx=24dBm) TBD

LTE in suspend mode TBD

LTE (16QAM) Tx=23 dBm TBD

GPS/GNSS tracking TBD

Connected standby TBD

<500mA <2800mA

<5mA

<800mA <1100mA

<4mA

<700mA <1000mA

<5mA <900mA <1200mA <150mA <300mA

<3mA

COMPANY CONFIDENTIAL

5. RF performance specifications

Radio performance for T77W595.00 is given in the following sections, including RF receiver,

RF transmitter.

5.1 RF maximum Tx power specifications

Table 5-1 Maximum transmit power

Mode Band Class

LTE

1,2/25,3,4,5/26,

7,8,13,12/17,20,28

3 23+/-2 23+/-1 23+2/-1

3GPP

Standard

Design

Spec.

MFG Spec.

WCDMA 1,2,4,5,8 3 24+1.7/-3.7 23.5+/-1 23.5+1/-2 CDMA BC0,BC1,BC10 3 23~30 24+0.5/-1 24+1/-1

GPRS

E-GPRS

1800,1900 1 30+/-3 30+/-1 30+/-2 850,900 4 33+/-3 32 +/-1 33+/-2 1800,1900 E2 26+/-3 25.5+/-1 26+/-2 850,900 E2 27+/-3 26.5+/-1 27+/-2

Remark:

Above table is for general application, please inform us if you have any further requirement.

Îor

COMPANY CONFIDENTIAL

5.2 RF min. Rx sensitivity specifications

Table 5-2 Conducted min. receiver sensitivity

LTE Band (10MHz BW) 3GPP (Combined) Design Target MFG Spec 1 -97dBm -101 dBm -100 dBm

2 -95dBm -101 dBm -98 dBm 3 -94dBm -101 dBm -99 dBm 4 -97dBm -102 dBm -100 dBm 5 -95dBm -101 dBm -99 dBm 7 -95dBm -99 dBm -98 dBm 8 -94dBm -102 dBm -99 dBm 12 -94dBm -100 dBm -98 dBm 13 -94dBm -100 dBm -98 dBm 17 -94dBm -101 dBm -98 dBm 20 -94dBm -101 dBm -99 dBm 25 -93.5dBm -101 dBm -98 dBm 26 -94.5dBm -102 dBm -99 dBm 28 -95.5dBm -101 dBm -100 dBm WCDMA 3GPP (Combined) Design Target MFG Spec 1 -106.7dBm -113 dBm -111 dBm 2 -104.7dBm -113 dBm -110 dBm 4 -106.7dBm -113 dBm -111 dBm 5 -104.7dBm -113 dBm -110 dBm 8 -103.7dBm -113 dBm -109 dBm GPRS / E-GPRS 3GPP Design Target MFG Spec GPRS 1800,1900 -102 dBm @ CS1 -109 dBm -107 dBm @ CS1 GPRS 850,900 -100 dBm @ CS1 -109.5 dBm -107 dBm @ CS1 EDGE 1800,1900 -98 dBm @ MCS5 -102 dBm -100 dBm @ MCS5 EDGE 850,900 -98 dBm @ MCS5 -102 dBm -100 dBm @ MCS5 CDMA 3GPP2 (Combined) Design Target MFG Spec BC0 -104dBm -112dBm -109dBm BC1 -104dBm -111dBm -109dBm BC10 -104dBm -112dBm -109dBm GPS/GLONASS tracking sensitivity

-152dBm -161dBm -155dBm

Remark:

a. It has 3dB margin at least refer to 3GPP standard or CDMA standard.

b. The typical value of LTE was measured as combine Rx sensitivity which was follow test

setup of 3GPP standard (TS36.521 charter 7.2 and charter 7.3.5), the test setup is follow

TS36.508 Annex A Figure A.3.

RX/TX

Ior

Splitter/ combiner

UE under Test

RX/TX

COMPANY CONFIDENTIAL

6. Software Features

6.1 USB Enumeration

When a USB device is attached to or removed from the USB, the host uses a process

known as bus enumeration to identify and manage the device state changes necessary.

When a USB device is attached to a powered port, the following actions are taken:

1. The hub to which the USB device is now attached informs the host of the event via a

reply on its status change pipe. At this point, the USB device is in the Powered state

and the port to which it is attached is disabled.

2. The host determines the exact nature of the change by querying the hub.

3. Now that the host knows the port to which the new device has been attached, the host

then waits for at least 100 ms to allow completion of an insertion process and for power

at the device to become stable. The host then issues a port enable and reset command

to that port.

4. The hub performs the required reset processing for that port. When the reset signal is

released, the port has been enabled. The USB device is now in the Default state and

can draw no more than 100 mA from VBUS. All of its registers and state have been

reset and it answers to the default address.

5. The host assigns a unique address to the USB device, moving the device to the

Address state.

6. Before the USB device receives a unique address, its Default Control Pipe is still

accessible via the default address. The host reads the device descriptor to determine

what actual maximum data payload size this USB device’s default pipe can use.

7. The host reads the configuration information from the device by reading each

configuration zero to n-1, where n is the number of configurations. This process may

take several milliseconds to complete.

8. Based on the configuration information and how the USB device will be used, the host

assigns a configuration value to the device. The device is now in the Configured state

and all of the endpoints in this configuration have taken on their described

characteristics. The USB device may now draw the amount of VBUS power described

in its descriptor for the selected configuration. From the device’s point of view, it is now

ready for use.

When the USB device is removed, the hub again sends a notification to the host. Detaching

a device disables the port to which it had been attached. Upon receiving the detach

notification, the host will update its local topological information.

The following diagram and table describe USB device states. Some of these states are

COMPANY CONFIDENTIAL

visible to the USB and the host, while others are internal to the USB device.

Figure 6-1. Device State Diagram

Table 6-1. Visible Device States

Attached Powered Default Address Configured Suspended

COMPANY CONFIDENTIAL

State

No -- -- -- -- -- Device is not

attached to the USB. Other attributes are not significant.

Yes No -- -- -- -- Device is attached

to the USB, but is not powered. Other attributes are not significant.

Yes Yes No -- -- -- Device is attached

to the USB and powered, but has not been reset.

Yes Yes Yes No -- -- Device is attached

to the USB and powered and has been reset, but has not been assigned a unique address. Device responds at the default address.

Yes Yes Yes Yes No -- Device is attached

to the USB, powered, has been reset, and a unique device address has been assigned. Device is not configured.

Yes Yes Yes Yes Yes No Device is attached

to the USB, powered, has been reset, has a unique address, is configured, and is not suspended. The host may now use the function provided by the device.

Yes Yes -- -- -- Yes Device is, at

minimum, attached to the USB and is powered and has not seen bus

COMPANY CONFIDENTIAL

activity for 3 ms. It may also have a unique address and be configured for use. However, because the device is suspended, the host may not use the device's function.

6.2 Windows Morphing

The device presents itself as different functions on different Windows OS. On windows 7, its

functions include Diag, RmNet, Modem, Application Interface and NEMA after the user

installs the driver package. On windows 8.1, its functions are MBIM and GPS after the user

installs the driver package. The devices that exhibit morphing behavior are referred to as

morphing devices. On Linux, its functions include Diag, ECM, Application Interface, Modem

and NMEA.

Windows morphing solution maps the morphing device’s USB configuration to a set of USB

functions. At any point in time, a single set of functions (by way of a configuration) are

exposed to the host. The solution achieves morphing by switching between these

configurations.

Logical configurations

The functions present in the device are grouped into the following logical sets.

Logical Set of

Table 6-2. Logical Set of Functions

Description

Functions

Windows-7-Configuration Configuration selected by Windows 7 and older versions of

Windows when the morphing device is inserted into the host.

Linux-Configuration Configuration selected by Linux when the morphing device is

inserted into the host.

Windows-8-Configuration Configuration selected by Windows 8 when the morphing device

is inserted into the host.

The following table shows the USB configurations listed in the previous table along with

possible interfaces and functions. Additional requirements for each configuration are

described in the remaining subtopics.

Table 6-2. Logical Set of Functions

Configuration 1 (Windows-7-Configuration) Diag RmNet Modem Application Interface

Configuration 2 (Linux-Configuration) Diag ECM Application Interface Modem

Configuration 3 (Windows-8-Configuration)

MBIM GPS

COMPANY CONFIDENTIAL

NMEA NMEA Goals of the solution

 In Windows 7, host sends SET_CONFIGURATION request with value 1 to MDM9625

device. The functions defined in Configuration 1 will be exposed to the host.

 In Linux, host sends SET_CONFIGURATION request with value 2 to MDM9625 device.

The functions defined in Configuration 2 will be exposed to the host

 In Windows 8, host sends SET_CONFIGURATION request with value 3 to MDM9625

device. The functions defined in Configuration 3 will be exposed to the host.

Configuration requirements

The Windows-7-Configuration should be the first configuration in the morphing device.

Windows 8 and Linux will not select this configuration. In Windows 7 and earlier versions of

Windows, the Windows-7-Configuration is the default configuration selected.

The Windows-8-Configuration exposes the MBIM function as one of the functions on which

MBCD (Mobile Broadband Class Driver) is loaded. In Windows 8, the value of this

configuration is used in the subCompatibleID value returned to USBCCGP. USBCCGP

selects this configuration when it is loaded. The Windows-8-Configuration should be either

Configuration 2, 3, or 4. No other configuration is supported as the

Windows-8-Configuration.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

This device is intended only for OEM integrators under the following conditions:

1. Antennas must be installed at least 2.5cm away from the user with no any metal part surrounding the radiating elements to affect the SAR pattern. OEM manufacture need to confirm SAR compliance if in doubt.

2. Only the identical antennas tested (including the excessive ground plane as shown in the certification filing) must be sued for portable product. Other antenna(s) even with the same antenna type and gain will need a class II permissive to verify the SAR compliance.

3. No co-transmission with other transmitter.

As long as 3 conditions above are met, further transmitter However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed

IMPORTANT NOTE: In the event that these conditions can not be met certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: “Contains FCC ID: MCLT77W595”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.

test will not be required.

(for example

be used on the

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end

product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.

This device is intended only for OEM integrators under the following conditions:

2. Only the identical antennas tested (including the excessive ground plane as shown

in the certification filing) must be sued for portable product. Other antenna(s) even with the same antenna type and gain will need a class II permissive to verify the SAR compliance.

3. No co-transmission with other transmitter.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:

1. Une. Les antennes doivent etre installes a au moins 2,5 cm loin de l'utilisateur, sans aucune partie metallique entourant les elements rayonnants a affecter le modele SAR. Fabrication OEM besoin pour confirmer la conformite SAR en cas de doute.

2. Seules les antennes identiques testes (y compris le plan excessive du sol, comme indique dans le depot de certification) doivent etre poursuivis pour produit portable. Autre antenne (s) meme avec le meme type et le gain d'antenne aura besoin d'un permissive classe II de verifier la conformite SAR.

3. Aucune co-transmission avec un autre emetteur.

Tant que les 3 conditions ci-dessus sont remplies, des essais supplémentaires sur

test will not be required.

l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM

sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.

End Product Labeling The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: “Contains IC: 2878D-T77W595”.

Plaque signalétique du produit final

L'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 2878D-T77W595".

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Manuel d'information à l'utilisateur final

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.

DETACHABLE ANTENNA USAGE

This device has been designed to operate with a PIFA antenna have a maximum gain of [6.14] dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated

power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter (IC: 2878D-T77W595/ Model: T77W595) has been approved by Industry Canada to operate with the antenna type, maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this user's manual, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de PIFA antenne avec dBi [6.33]. Une antenne à gain plus élevé est strictement interdite par les règlements d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante.

Le présent émetteur radio (IC: 2878D-T77W595/ Modèle: T77W595) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

HON HAI PRECISION IND T77W595 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual