HON HAI PRECISION IND T60H656 Revised Manual

U S E R ’ S M A N U A L
T60H656
Mini-PCI Type IIIB WLAN CARD
Ambit Microsystems Corporation
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: Ambit@shts.seed.net.tw
1
Contents
1.1 F
1.1.1 W
1.2:FCC N
1.2.1 FCC C
1.2.2 FCC C
EATURES...............................................................................................................................1
IRELESS LAN FUNCTION.....................................................................................................1
OTICE...................................................................................................................................2
OMPLIANCE.........................................................................................................................
LASS B STATEMENT .........................................................................................................2
SECTION TWO: WIRELESS LAN INSTALLATION...............................................................3
2-1 S
YSTEM REQUIREMENTS ................................................................................................................3
2-2 I
NSTALLATION AND UNINSTALL PROCESS.......................................................................................3
SECTION THREE: WIRELESS UTILITY AND CONFIGURATION.....................................9
3-1 W
INDOWS 98/ME/2000 WIRELESS UTILITY...................................................................................9
SECTION FOUR: WINDOWS XP WIRELESS UTILITY AND CONFIGURATION...........15
4-1 W
INDOWS XP WIRELESS UTI L I TY................................................................................................15
APPENDIX A GLOSSARY................................................................................................................22
The information contained in this manual has been verified at the time of this manual printing. The manufacturer reserves the right to make any changes and improvements in the product described in this manual at any time and without notice. All registered trademarks are the property of their respective owners.
2
Section One: Introduction
Ambit Wireless Mini-PCI Module complied with IEEE 802.11b 11Mbps Standard, it can be used to provide a variety of low-cost wireless network interface card to connect your wireless LAN via fitting into the MiniPCI Type III slot . The Wire less Mini PCI Module that complies with this specification and combines networking with high­speed Internet access will let people connect to the Internet anywhere, anytime.
With seamless roaming, fully interoperability and advanced security with WEP standard, Wireless MiniPCI Module can allow user to switch to different vendors’ Access Points through the wireless networks and to prevent from eavesdropping.
1.1 Features
1.1.1 Wireless LAN Function
Form Factor & Bus Interface MiniPCI Type IIIB, compliant to MiniPCI
Specification Rev 1.0 Wireless LAN Compliance IEEE 802.11b Radio Technology Direct Sequence Spread Spectrum Operating Frequency 2.4 ~ 2.497GHz ISM band Modulation Schemes DQPSK, DBPSK and CCK Channel Numbers IEEE 802.11b compliant
1 ~ 11 channels for United States
1 ~ 13 channels for Europe
1 ~ 13 or 14 channels for Japan WLAN Data Rate 11, 5.5, 2, and 1Mbps Spreading 11-chip Barker Sequence Media Access Protocol CSMA/CA with ACK Transmitter Output Power Typ. 13+/-1 dBm Receiver Sensitivity Typ. –82 dBm for 11Mbps @ 8% PER
Typ. –85 dBm for 1Mbps @ 8% PER Antenna Type Integrated diversity switch with Hirose
compliant connectors(U-FL) for connecting
dual diversity antennas
1
Operating Voltage 3.3VDC Radio On / Off Dynamic Rate Shifting Automatic fallback Network Architecture Ad-hoc, Infrastructure Operating Systems Windows 98/Me/2000/XP Mechanical Requirements Mini-PCI Type IIIB dimension.
1.2:FCC Notice
1.2.1 FCC Class B Statement
This equipment has been tasted and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interferencr by one or more of the following measures:
! Reorient or relocate the receiving antenna ! increase the separation between the equipment and the receiver ! Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
! Consult the dealer or an experienced radio/TV technician for help
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). The OEM integrator is required to label their end product using this module by the warning statement such as “This product integrate an RF module with FCC ID: MCLT60H656”. The OEM integrator is not allowed to use the antenna which is not included in this authorization. Also the warning statement of the use of the antenna which is not approved in this authorization should be also included in the users manual of the end product.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and Obtaining a separate FCC authorization.
antenna.
2
Caution: For your health sake, please keep at least 20 cm away from your Notebook LCD Panel
while using wireless LAN.
3
Section Two: Wireless Lan Installation
2-1 System Requirements
In order to install Wireless LAN driver and Utility and use the Wireless LAN card in your notebook computer. Your notebook system must meet the following requirements:
! Ambit Mini-PCI Wireless LAN Card already inserted ! Windows 98SE,2K,ME,XP OS Support
2-2 Installation and Uninstall Process
Install Wireless LAN (Windows 98/2K/ME/XP)
1. While power on and open Windows OS at first time, the OS will detect Wireless LAN
Card exist and pop up the following dialogue. If you don’t want to perform install process now, then press ‘Cancel’ bottom. If you want to install now, please wait a moment then you can see the next InstallShield Wizard dialogue pop up.
If you press ‘Cancel’ Bottom at the above dialogue, but you want to start install process later. Execute the program ‘Setup.exe’ in the CD. Windows displays the dialog as below. Press ‘Next’ button to continue.
4
2. It displays a License Agreement dialog. Press ‘Next’ to continue.
5
3. Select the destination folder that you want to place the files.
4. Wait for the install program to do the installation.
6
+ 17 hidden pages