Hong Kong Easyweld Limited EasyCT 213, EasyCT 312 Operation Manual

EasyWeld

EasyCT 213/312

Multipurpose

Tig / Plasma Cutter

Operation Manual

Hong Kong EasyWeld Limited

1

Introduction

The EasyCT series of Welders is a revolutionary new approach to Welding
technology. Easyweld introduced a more efficient way to manufacture top
quality machines while keeping the cost of operation and repairs lower. This was
accomplished using several new approaches to the mainstream technology. One
of these methods is our proprietary plug-and-play main circuit boards which
allow ease of repair, reducing the downtime to only hours rather than days,
while also reducing repair costs averaging less than $75! The EasyCT 213/312
uses special safety redundant circuitry with built in auto-protection and self
adjusting circuitry to keep your machine running in a safe threshold. This helps
protect your machine from over-voltage, power spikes, burn-outs and shorting.

Warranty

The machine is insured against damage upon shipping. If you machine is
damaged in any way when you receive it, you must retain all shipping materials
and packing. Call our customer service department and report the damage
immediately.

There is a 1 year warranty on all internal electronic parts. The torch, power cord,
clamps, air regulator, hoses, case & paint and consumables and cables are not
covered under warranty. You must use dry gas in your machine and keep it
indoors away from rain and moisture.

This machine is designed to operate from 200-240vac at 50-60Hz Only.
Operating outside of limits will void warranty.

Warranty coverage covers repair or replacement of damaged machine or
damaged circuit board. Warranty does not cover shipping from the customer but
does cover return shipping within the Cont. United States. If you are going to
return a machine to us for repairs, it must be well packed and insured.

Customers who own machines that require warranty coverage should contact
our warranty department by email at [e-mail] to obtain a return
authorization code.

Customers who own an out-of-warranty machine that require repairs should
contact us for an estimate.

2

CONTENTS

- Warning 4

- General Description 5

- Main Parameter 6

- Installation 7

- Operation 9

- Caution 9

- Maintenance 10

- Troubleshooting 10

3

Welding and cutting is dangerous to the operator, people in or near the working
area, and the surrounding, if the equipment is not correctly operated. Therefore,
the performance of welding/cutting must only be under the strict and
comprehensive observance of all relevant safety regulations. Please read and
understand this instruction manual carefully before the installation and
operation.

• The switching of function modes is possibly damaging to the equipment, while
the welding operation is performed.

• Do disconnect the electrode-holder cable with the equipment, before the
performance of welding.

• A safety switch is necessary to prevent the equipment from electric-leakage.

• Welding tools should be of high quality.

• Operators should be qualified.

Electric Shock: It may be fatal

• connect the earth cable according to standard
regulation.

• Avoid all contact with live components of the

welding circuit, electrodes and wires with bare
hands. It is necessary for the operator to wear dry
welding gloves while he performs the welding task.

• The operator should keep the working piece insulating from himself/herself.

Smoke and Gas generated wile welding or cutting:
harmful to people’s health.

• Avoid of breathing the smoke and gas of welding or

cutting.

• Keep the working area in good ventilation.

Arc light-emission: harmful to people’s eyes and
skin

• Wear the welding helmet, anti-radiation glass and
work clothes while the welding operation is
performed.

• Measures also should be taken to protect people in

or near the working area.

Fire hazard

• The welding splash may cause fire, thus remove
flammable material away from the working place.

• Have a fire extinguisher nearby, and have a train fire
person ready to use it.

Noise: Possibly harmful to peoples’ hearing.

• Surface noise is generated while welding/cutting,
the hearing aids is necessary in some cases.

Machine Fault:

• Consult this instruction manual.

• Contact your local dealer or supplier for further
advice.

4

WARNING