Honeywell RCWL3506A, RCWL3502A, RCWL35N, RCWL3505A, RCWL3501A User Manual
Installation
Instructions
RCWL35 Series
RCWL35N, RCWL3501A, RCWL3502A, RCWL3503A,
RCWL3504A, RCWL3505A, RCWL3506A
Decorative Wire Free Chimes and Push
69-2115EFS-05
69-2115EFS_C.indd 1 12/17/2007 2:23:55 PM
Installation Instructions
69-2115EFS—05 ii
Contents
Safety ..........................................................2
Checking pack contents ............................ 2
Open bell push ...........................................3
Install the push battery .............................. 3
Open the chime .......................................... 3
Install the chime battery ............................3
Test the kits ................................................4
Volume control ...........................................5
Change tunes .............................................5
Add new push/reprogram ..........................6
Unlearn procedure .....................................6
Recall function ...........................................6
Mount chime ..............................................7
Paint the wood cover.................................8
Specifications .............................................9
Troubleshooting .........................................9
Disposal and recycling ............................12
Guarantee ................................................. 12
Declaration ...............................................13
69-2115EFS_C.indd 2 12/17/2007 2:23:55 PM
RCWL35 Series
1 69-2115EFS—05
ICON
WIRELESS CHIME BASE
DECORATIVE
CHIME COVERS
DECORATIVE CHIME COVERS
LED
VOLUME
CONTROL
TUNE BUTTON
PROGRAM
BUTTON
Compatible with décor wireless push, converter, motion detector, and door contact.
(Model No. RPWL30XXX series, and RCA901N and RCA902N.)
69-2115EFS_C.indd 1 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 2
Decorative Wire Free Chimes and Push
Checking Pack Contents
• Chime
• Bell push (for chime kit only)
• CR2032 battery for bell push (for
chime kit only)
• 2 x fixing screws for push (for chime
kit only)
• 2 x fixing screws for chime
• Wall plugs
• Adhesive pad (for chime kit only)
You will need:
• A Phillips screwdriver
• A small flat bladed screwdriver
• A 1/4-in. (6 mm) masonry drill
• 4 X LR14 ‘C’ Alkaline batteries
Safety
Before proceeding with the installation, please note the following safety warnings:
• Always follow the manufacturer’s advice when using power tools and wear
suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
• Before drilling holes in walls, check for hidden electricity cables and water pipes.
The use of a cable/pipe locator is advisable if in doubt.
69-2115EFS_C.indd 2 12/17/2007 2:23:56 PM
RCWL35 Series
3 69-2115EFS—05
Installation
1. Open the bell push and insert the push battery
(CR2032).
2. Open the chime cover.
3. Insert chime batteries (LR14 C size).
69-2115EFS_C.indd 3 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 4
4. Operate push. Chime will play the default tune. First icon
will illuminate.
Note: The bell push (if supplied) is preprogrammed to operate with the chime.
Installation
3 FT (1 M)
69-2115EFS_C.indd 4 12/17/2007 2:23:56 PM
RCWL35 Series
5 69-2115EFS—05
5. To adjust volume.
Installation
6. To change tunes
Press push button, chime will play tune, while
the icon on chime is flashing, press and release
tune button . Press and release button
again to cycle through the available tunes
until you hear the tune you want. The last
tune played will be stored after the icon stops
flashing. To confirm, press the push button and
chime will play the tune you want.
69-2115EFS_C.indd 5 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 6
7. To add new push/reprogram
Press and hold the program button l. The icons will illuminate
in sequence. Release the program button when icon you
choose is illuminated. Operate your new push and the chime
will play tune, icon will flash. To change tune, refer to step 6.
8. Unlearn procedure
To remove a push from the chime’s memory, press and hold the
program button l. Each icon will light in turn. When the icon
associated with the push to be un-learned is lit, release the button. Then press
and hold down both l and buttons, until a ‘beep’ sound is heard.
9. Recall function
A short push of the program button l will flash the icon that was last in use.
Installation
69-2115EFS_C.indd 6 12/17/2007 2:23:56 PM
RCWL35 Series
7 69-2115EFS—05
10. Mount the bell push
Install back cover to wall, use screws provided/adhesive
pad. Close the cover.
Note: Before final installation adjust distance and position
between push and chime to optimize the chime within your
environment. Dense walls and metal can reduce range.
TOP
Installation
Wall Type Range Reduction
Dry-lined partition wall 10–30%
Single-layer brick wall 20–40%
Double-layer brick wall 30–70%
Metal panel/radiator 90–100%
69-2115EFS_C.indd 7 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 8
12. For stainable covers only
Choose your paint, stain or varnish and then
apply to the cover. Follow manufacturers’ advice
on the paint/vanish. It is possible to unscrew
the four screws shown below for painting.
Ensure you screw it back with the same screws
provided!
Once completed, clip it onto the base as in step 11.
Installation
11. Mount the chime
Mounting holes are marked with
screw symbol. Clip on the front
cover.
69-2115EFS_C.indd 8 12/17/2007 2:23:56 PM
RCWL35 Series
9 69-2115EFS—05
Troubleshooting
A ‘beep’ sound is heard in learn mode…
• The push you are programming has already been learned by the chime.
• If you want to change the icon associated with the push, use the unlearn procedure,
then program the push again.
Specification Chime Bell push
Operating Temperature 32°F to 104°F
0ºC to 40ºC
14°F to 104°F
-10ºC to 40ºC
RF Frequency- US 916.8 MHz 916.8 MHz
Range (open field) 450 ft. (140 m)
Sound Level (typical) 90dBA @ 3 ft. (1 m) RF Power - <1mW
Battery Type LR14 (C size) CR2032
Battery Life (5 activations/day) 12 months 18 months
Rain proof N/A Pass UL1598 rain test
69-2115EFS_C.indd 9 12/17/2007 2:23:57 PM
Installation Instructions
69-2115EFS—05 10
Troubleshooting
Two ‘beep’ sounds are heard after the normal chime sound…
• This indicates a low battery in the bell push that activated the chime. Install a new
battery, type CR2032.
When the bell push is operated, the amber confidence light does not turn on,
or is only on for a short time…
• In normal operation, the amber light will turn on for 1 second. When the battery is
weak, the light will only turn on for a short time. Install a new battery, type CR2032.
The chime does not work…
• Check that the batteries are the correct type, LR14 ‘C’ cells. Only use alkaline
batteries.
• Check that the batteries are fitted correctly. (No wrong polarity)
• The chime could be out of range of the bell push. Try the chime in a different location.
• The chime might not have learned the identity of the bell push. Follow the
programming procedure.
69-2115EFS_C.indd 10 12/17/2007 2:23:57 PM
RCWL35 Series
11 69-2115EFS—05
Troubleshooting
The chime does not sound…
• Check that the volume control is not at the minimum setting.
Range is reduced…
• Metal structures, including uPVC door frames can reduce the range of the product.
Avoid mounting the push or chime on or near metal structures.
• Other equipment can cause radio interference that affects your chime.
• Walls and ceilings will reduce the range.
• Weak batteries will reduce range. Replace every 12–18 months. In cold conditions
(below 41ºF [5ºC]), batteries may need to be replaced more often.
Amber light flashes…
• When the chime battery is low, an amber light located at the side of the chime will
flash every 5 seconds. Fit new batteries in the chime, type LR14 ‘C’ cells. Only use
alkaline batteries.
69-2115EFS_C.indd 11 12/17/2007 2:23:57 PM
Installation Instructions
69-2115EFS—05 12
Disposal & Recycling
Batteries and waste electrical products should not be disposed of with household
waste. Please recycle where these facilities exist. Check with your local authority or
retailer for recycling advice.
Guarantee
Honeywell guarantees this product for 1 year from the date of purchase. Proof of purchase is required; this does not affect your statutory rights. If you require further information about your product, call the Honeywell helpline at 1-800-468-1502.
69-2115EFS_C.indd 12 12/17/2007 2:23:57 PM
RCWL35 Series
13 69-2115EFS—05
Declaration
Honeywell hereby declares that this product complies with Part 15 of the FCC rules
and Industrial Canada standards.
This device operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Caution:
Changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.
69-2115EFS_C.indd 13 12/17/2007 2:23:57 PM
Loading...