Honeywell M9181D, M9164, M9174, M9182A, M9184 Product Data
...
PRODUCT DATA
63-2631-07
Series 90
Modutrol IV
™
Motors
APPLICATION
The Series 90 Modutrol IV™ Motors are spring return and
non-spring return modulating proportional control motors. Use
these motors with controllers that provide a Series 90 output
to operate dampers or valves.
FEATURES
• Replaces M934A,D, M941, M944A,C,D, M945A,D,F,
M954, M965, and M975 motors.
• Integral junction box provides NEMA 3 weather
protection.
• Integral spring return returns motor to normal position
when power is interrupted.
• Motor and circuitry operate from 24 Vac. Models
available with factory installed transformer, or a field
added internal transformer.
• Quick-connect terminals are standard—screw terminal
adapter is available.
• Adapter bracket for matching shaft height of older
motors is available.
• Motors have field adjustable stroke (90° to 160°).
• Die-cast aluminum housing.
• Integral auxiliary switches are available factory
mounted, or can be field added.
• Nominal timing standard of 30 seconds (90° stroke),
and 60 seconds (160° stroke). Other timings available.
• Spring return motors can operate valve linkages form
power end or auxiliary end shafts for normally closed
or normally open valve applications.
• All models have dual shafts (slotted and tapped on
both ends).
• All models have auxiliary switch cams.
• Fixed torque throughout the entire voltage range.
• Motors are designed for either normally open or
normally closed valves and dampers.
• Field addable interface modules can be mounted in the
junction box to upgrade the motor to Series 70
(electronic) control.
Contents
Application ........................................................................ 1
Features ........................................................................... 1
Specifications ................................................................... 2
Ordering Information ........................................................ 2
Wiring ............................................................................... 7
Settings and Adjustments ................................................. 10
Operation .......................................................................... 11
Checkout .......................................................................... 13
Replacement .................................................................... 13
SERIES 90 MODUTROL IV™ MOTORS
63-2631—07 2
ORDERING INFORMATION
When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the
TRADELINE® Catalog or price sheets for complete ordering number . If you have additional questions, need further information,
or would like to comment on our products or services, please write or phone:
1. Your local Honeywell Environmental and Combustion Controls Sales Office (check white pages of your phone directory).
2. Honeywell Customer Care
1985 Douglas Drive North
Minneapolis, Minnesota 55422-4386
3. http://customer.honeywell.com or http://customer.honeywell.ca
International Sales and Service Offices in all principal cities of the world. Manufacturing in Belgium, Canada, China, Czech
Republic, Germany, Hungary, Italy, Mexico, Netherlands, United Kingdom, and United States.
SPECIFICATIONS
TRADELINE Models: Selected and packaged to provide
ease of stocking, ease of handling and maximum replacement value. Specifications are the same as those of standard models unless specified otherwise.
NOTE: Auxiliary switches can only be added to motors
that include auxiliary switch cams. (These cams
cannot be field-added.)
Modutrol IV Order Number Guide: See Table 1.
Table 1. Modutrol IV Series 2 and 3 Model Number Guide.
NOTE: Torque designation corresponds to torque rating at standard timing (nominally 60 sec for 160° and 30 sec for 90° except
for 300 lb-in. motors which have timings of 2 or 4 min).
Dimensions: Refer to Fig. 2.
Electrical Ratings: Refer to Table 2.
Control Inputs: Proportional, Series 90.
NOTE: Motor Series 90 control can be either Electronic,
or Mechanical (135 ohm).
Auxiliary Switch Ratings: Refer to Table 3.
Ambient Temperature Ratings:
Maximum: 150° F (66° C) at 25% duty cycle.
Minimum: -40° F (-40° C).
NOTE: 25% duty cycle indicates that the motor operates
for 6 out of every 24 hours.
Dead Weight Load On Shaft:
Power or Auxiliary End: 200 lb (90.8 kg) maximum.
Maximum Combined Load: 300 lb (136 kg). (Dual shaft
motors only.)
Crankshaft: 3/8 in. (9.5 mm) square. (All models built after
2006 have dual end shaft.)
M Motor
91 Proportioning Series 90 Control
94 Flame Safeguard Firing Rate Motor
6 60 lb-in. Spring Return 35 lb-in. Non-Spring Return
7 75 lb-in. Non-Spring Return
8 150 lb-in. Non-Spring Return
9 300 lb-in. Non-Spring Return
1 Dual-ended shaft Non-Spring Return
2 Normally Closed (NC) Spring Return
4 Non-Spring Return
5 Normally Closed (NC) Spring Return
A 0 Auxiliary Switches Adjustable Stroke Normally Closed
B 1 Auxiliary Switch
C 2 Auxiliary Switches
D 0 Auxiliary Switches
E 1 Auxiliary Switch
M 91 8 4 A XXXX See Catalog for Complete O.S. Number
SERIES 90 MODUTROL IV™ MOTORS
3 63-2631—07
Fig. 1. Stroke.
Fig. 2. Modutrol IV Motor mounting dimensions in inches (mm).
Stroke: Models available with field adjustable stroke from 90° to 160° (See Settings and Adjustments figure 11).
FULLY OPEN
90 DEGREE STROKE 160 DEGREE STROKE
M31079
VERTICAL
REFERENCE
FULLY CLOSED
160
10
VERTICAL
REFERENCE
FULLY CLOSED
90
10
FULLY OPEN
VERTICAL
REFERENCE
VERTICAL
REFERENCE
FULLY CLOSED
FULLY OPEN
FULLY
CLOSED
FULLY
OPEN
90 DEGREE STROKE 160 DEGREE STROKE
NON-SPRING RETURN MOTORS
160
10
90
45
SPRING RETURN MOTORS AND NON-SPRING RETURN MOTORS
ASYMMETRICAL MOTORS
SYMMETRICAL MOTORS
M18998D
4-7/8
(124)
5-1/2
(140)
13/16
(20)
4-1/16 (103)
1/4
(7)
1-1/2 (37)
5-1/2 (140)
JUNCTION
BOX
MOTOR
AUXILIARY
END
POWER
END
ADAPTER
BRACKET
2-9/16
(66)
5-3/8
(137)
6-7/16
(164)
9/16 (15)
3/4
(19)
TOP VIEW OF BRACKET TOP VIEW
4-5/8
(116)
4-1/4
(107)
2-5/16
(58)
11/16
(17)
4-7/8 (124)
5-9/16 (141)
1/4 (7)
5-13/16
(148)
1
POWER END
2
3
1-1/2 (37)
3/4
(19)
SPRING RETURN MODEL SHOWN
FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
FOR NON-SPRING RETURN MODELS 7-5/16 (185).
FOR 60 LB-IN. SPRING RETURN MODELS (SHOWN).
FOR NON-SPRING RETURN MODELS.
1
2
3
13/16
(20)
SERIES 90 MODUTROL IV™ MOTORS
63-2631—07 4
T a ble 2. Power Consumption Ratings.
Table 3. Auxiliary Switch Ratings (in Amps).
a
40 VA pilot duty, 120/240 Vac on opposite contact.
Timing And Torque: Refer to Table 5.
Approvals:
Underwriters Laboratories Inc. Listed: File No. E4436, Guide
No. XAPX to US and Canadian standards.
U.S. Patents: pending
Table 4. Primary 50017460-001 Color Code
All Transformers have brown secondary (24 VAC) wires.
Table 5. Series 90 Modutrol Motor Timing and Torque Ratings.
a
Timings apply to all TRADELINE models. Some OEM models are available with non-standard timing/torque.
b
The torque rating for dual-ended shaft motors is the sum of the shaft torques (power-end torque plus auxiliary-end torque).
c
Breakaway torque is maximum torque available to overcome occasional large loads such as a seized damper or valve.
d
Low timing is for M9184D1005 only.
NOTE: Some 150 lb-in. and 300 lb-in. torque adjustable stroke motors have timings that are twice that of the nominal timing.
IMPORTANT
Never use a Modutrol Motor continuously at the
Breakaway Torque rating.
Accessories:
220736 Internal Auxiliary Switch Kit can be field-installed.
One- (220736A) and Two- (220736B) switch kits available.
220738A Adapter Bracket raises motor shaft height by 19 mm
to match that of previous Modutrol Motor models.
220741A Screw Terminal Adapter converts the standard
quick-connect terminals to screw terminals.
221455A Infinitely Adjustable Crank Arm approximately 0.75
inch shorter than the 4074ELY Crank Arm, can rotate
through downward position and clear base of motor without
requiring use of adapter bracket.
221508A Resistor Board plugs onto Series 90 Motor quick-
connect wire terminals. Provides same functionality as
4074BYK, 4074EAU, 4074EDC, or 4074EED Resistor Kits.
4074BYK Series 90 Resistor Kit provides for unison control of
up to six Series 90 Motors.
4074EAU W973 Resister Kit provides for control of two or three
Series 90 Motors from a W973 Single-zone Logic Panel or
W7100 Discharge Air Controller.
4074EDC 4-20 mA Resistor Kit drives one Series 90 Motor
from a 4-20 mA controller.
4074EED Unison Control 4-20 mA Resistor Kit provides for
control of up to four Series 90 Motors from one 4-20 mA
controller.
4074ERU Weatherproofing Kit provides NEMA 3 rating for
Modutrol IV Motors mounted in position other than upright.
50017460-001 Internal Transformer; 24/120/230 Vac 50/60 Hz
primary, 24 Vac secondary, quick connect terminals.
50017460-003 Internal Transformer; 120 Vac 50/60 Hz pri-
mary, 24 Vac secondary, quick connect terminals.
7617ADW Crank Arm approximately 0.75 inch shorter than
7616BR Crank Arm. Can rotate through downward position
and clear base of motor without requiring use of adapter
bracket.
Q100 Linkage connects Modutrol Motor to V51 Butterfly Valve.
Requires the 220738A adapter bracket (packed with
TRADELINE Modutrol IV Motors).
Power Consumption
Family VA Rating
M9161V 10
M9164 10
M9172W 20
M9174 12
M9175B 20
M9181D 10
M9182A 15
M9182D 20
M9184 15
M9185 20
M9186G 20
M9191F 15
Single Contact Rating
a
120 V 240 V
Full Load 7.2 3.6
Locked Rotor 43.2 21.6
Lead Color Primary Voltage
Brown 24 VAC
White 120 VAC
Blue 230 VAC
Black Common
Nominal Timinga in sec
Rated Torque in lb-in. (N•m)
b
Normal Running Torque Breakaway Torque
c
90° 160° Spring Return Non-Spring Return Spring Return Non-Spring Return
30 60 — 35 (4) — 70 (8)
15
d
/30 30d/60
60 (6.8) 75 (8.5) 120 (13.6) 150 (17)
30 60 — 150 (17) — 300 (34)
60 120 — 300 (34) — 600 (68)
SERIES 90 MODUTROL IV™ MOTORS
5 63-2631—07
Q181 Auxiliary Potentiometer for sequence or unison control of
1 to 4 additional modulating (Series 90) motors.
Q209E,F Potentiometer limits motor minimum position.
Q5001 Bracket and Linkage Assembly connects Modutrol
Motor to a water or steam globe valve.
Q605 Damper Linkage connects motor to damper. Includes
motor crank arm.
Q607 External Auxiliary Switch controls auxiliary equipment as
a function of motor position.
Q7130A Interface Module with selectable voltage ranges
(4-7 Vdc, 6-9 Vdc, and 10.5-13.5 Vdc) adapts motor to
M71XX function.
Q7230A Interface Module with selectable control (2-10 Vdc or
4-20 mA) and adjustable zero and span adapts motor to
M72XX function.
Q7330A Interface Module for W936 Economizer applications
adapts motor to M73XX function.
ES650-117 Explosion-Proof Housing encloses motor for use in
explosive atmospheres. Also required, a 7617DM coupling
assembly from Honeywell to use with the cover . Not for use
with Q5001 (or any other valve linkages).
To order ES-650-117, contact EGS Enclosures at
(281) 449-6271, ask for the sales department and for
distribution in your area.
Table 6. Modutrol Motor Cross-Reference.
INSTALLATION
When Installing this Product...
1. Read these instructions carefully. Failure to follow them
could damage the product or cause a hazardous condition.
2. Check the ratings given in the instructions and on the
product to make sure the product is suitable for y our
application.
3. Installer must be a trained, experienced service technician.
4. After installation is complete, check out product operation as provided in these instructions.
CAUTION
Electrical Shock or Equipment Damage Hazard.
Can shock individuals or short equipment circuitry.
Disconnect all power supplies before installation.
Motors with auxiliary switches can have more than one
disconnect.
CAUTION
Equipment Damage Hazard.
Can damage the motor beyond repair.
Never turn the motor shaft by hand or with a wrench.
Forcibly turning the motor shaft damages the gear train
and stroke limit contacts.
IMPORTANT
Always conduct a thorough checkout when
installation is complete.
Location
Allow enough clearance for installing accessories and motor
servicing when selecting a location (See Fig. 2). If located
outdoors, use liquid-tight conduit connectors with the junction
box to provide NEMA 3 weather protection. If mounted
outdoors in a position other than upright, install a 4074ERU
Weatherproofing Kit and liquid-tight connectors to provide
NEMA 3 protection.
CAUTION
Motor Damage Hazard.
Deteriorating vapors and acid fumes can damage
metal parts.
Install motor in areas free of acid fumes and other
deteriorating vapors.
In excessive salt environments, mounting base and screws
should be zinc or cadmium plated, not stainless steel or brass.
Use the 220738A Adapter Bracket for mounting on these
surfaces.
Original Motor Replacements
M944A,C,D, M954 M9184, M9194
M934D M9164, M9174
M945A,D,F, M955 M9182, M9185
M941 M9484, M9494
Loading...