Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
Wi-Fi Module Data Sheet
This device is pre-calibrated and integrates the complete transmit/receive RF paths
including band pass filter, diplexer, switches, reference crystal oscillator, and
power manage units (PMU).
The HON-ST60Q device supports IEEE 802.11 ac 1X1 receive multi-user MIMO spatial
stream multiplexing with data rates up to MCS9 (433.3 Mbps).
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
Advanced WLAN
▪ A-MPDU RX (de-aggregation) and TX (aggregation) supports 802.11ac single-MPDU
A-MPDU.
▪ Multi-BSS/Station
▪ Transmit rate adaption, transmit power control
▪ Modulation and coding scheme (MCS): 802.11ac—MCS0-9 & 802.11n—MCS0-7
▪ Dynamic frequency selection (radar detection) DFS
▪ 20/40/80 MHz channel bandwidths support
▪ On-chip gain selectable LNA with optimized noise figure and power consumption
▪ Internal PA with optimized gain distribution for linearity and noise performance
▪ Support wide variety of WLAN encryption: TKIP/WEP/AES
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
SPECIFICATIONS
Main Chip：Marvell 88W8997 (WLAN);
Input Voltage Requirements: DC 3.3 V ±10%
Operating Temperature: -30° to 85°C (-22° to 185°F)
Operating Humidity: 10 to 90% (non-condensing)
Storage Temperature: -40° to 85°C (-40° to 185°F)
Storage Humidity: 10 to 90% (non-condensing)
Maximum Electrostatic Discharge Conductive 4KV;
Air coupled 8KV follow EN61000-4-2
Wi-Fi Media: Direct Sequence-Spread Spectrum (DSSS)
Complementary Code Keying (CCK)
Orthogonal Frequency Divisional Multiplexing (OFDM)
Wi-Fi Media Access Protocol:
Carrier sense multiple access with collision avoidance (CSMA/CA)
A- MPDU Rx (De-aggregation) and Tx (aggregation) (802.11ac single-MPDU A-MPDU
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
Feature
Wi-Fi Standards:
IEEE 802.11a, 802.11b, 802.11d*, 802.11e, 802.11g, 802.11h, 802.11i, 802.11k*, 802.11n,
802.11r, 802.11s*, 802.11v*, 802.11ac * Summit version only
Wi-Fi Data Rates Supported:
Support 802.11 ac/a/b/g/n 1X1 MIMO.
802.11b (DSSS, CCK) 1, 2, 5.5, 11 Mbps
802.11a/g (OFDM) 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n (OFDM, HT20/HT40, MCS 0-7)
802.11ac (OFDM, HT20, MCS0-8; OFDM HT40/HT80, MCS 0-9)
2.4 GHz Frequency Bands
ETSI: 2.4 GHz to 2.483 GHz & FCC: 2.4 GHz to 2.473 GHz
2.4 GHz Operating Channels
ETSI: 13 (3 non-overlapping) & FCC: 11 (3 non-overlapping)
5 GHz Frequency Bands
ETSI
5.15 GHz to 5.35 GHz (Ch 36/40/44/48/52/56/60/64)
5.47 GHz to 5.725 GHz (Ch 100/104/108/112/116/120/124/128/132/136/140/144)
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
FCC
5.15 GHz to 5.35 GHz (Ch 36/40/44/48/52/56/60/64)
5.47 GHz to 5.725 GHz (Ch 100/104/108/112/116/120/124/128/132/136/140/144)
5.725 GHz to 5.85 GHz (Ch 149/153/157/161/165)
5 GHz Operating Channels (Wi-Fi)
ETSI: 19 non-overlapping; FCC: 24 non-overlapping
Transmit Power:
802.11a: 15 dBm +/- 1dBm
802.11b: 13 +/- 1dBm
802.11g: 13 +/- 1dBm
802.11n (2.4GHz) HT20 & HT40: 13 +/- 1dBm
802.11n (5GHz) HT20: 15 dBm +/- 1dBm
802.11n (5GHz) HT40: 14 dBm +/- 1dBm
802.11ac (5GHz) VHT20: 16 dBm +/- 1dBm
802.11ac (5GHz) VHT40: 14 dBm +/- 1dBm
802.11ac (5GHz) VHT80: 10 dBm +/- 1dBm
Typical Receiver Sensitivity:
802.11a: -89dBm
802.11b: -95dBm
802.11g: -91dBm
802.11n (2.4 GHz): -91dBm
802.11n (5 GHz): -89dBm
802.11ac (5 GHz): -89dBm
Operating Systems Supported:
Linux 3.x to 4.9.x kernel
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
DIMENSIONS ARE IN MM
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
Compliance Information
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generate, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important Note
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the US/Canada.
This device is intended only for OEM integrators under the following conditions:
1. The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2. The transmitter module may not be co-located with any other transmitter or antenna,
3. For all products market in US, OEM must limit the operation channels in CH1 to CH11
for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or
info to the end-user regarding to Regulatory Domain change.
If the three conditions above are met, further transmitter testing is not required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
Important Note
If these conditions cannot be met (for example certain laptop configurations or co-
location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID cannot be used on the final product. In these circumstances, the
OEM integrator is responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The end
product must be labeled in a visible area with the following: Contains FCC ID: HD5-
HONST60Q.
Manual Information to the End User
The OEM integrator must be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
The end user manual shall include all required regulatory information/warning as show
in this manual.
Industry Canada Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to
the following two conditions:
▪ This device may not cause interference; and
▪ This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
▪ l’appareil ne doit pas produire de brouillage;
▪ l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
This radio transmitter (IC: 1693B-HONST60Q) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 1693B-HONST60Q) a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
Caution:
(i) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with EIRP limit;
(iii) For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies with
the EIRP limits specified for point-to-point and non-point-to-point operation as
appropriate; and Operations in the 5.25-5.35GHz band are restricted to indoor usage
only.
Avertissement:
(i) les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés
uniquement pour une utilisation
à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
(ii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
pour les dispositifs utilisant les bandes de 5250 à 5350MHz et de 5470 à 5725 MHz doit
être conforme à la limite de la p.i.r.e;
(iii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
(pour les dispositifs utilisant la bande de 5725 à 5850 MHz) doit être conforme à la limite
de la p.i.r.e. spécifiée pour l'exploitation point à point et l'exploitation non point à point,
selon le cas;
Les opérations dans la bande de 5.25-5.35GHz sont limités à un usage intérieur
seulement.
Radiation Exposure Statement
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Déclaration d'exposition aux radiations
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
Cet équipement est conforme Canada limites d'exposition aux radiations dans un
environnement non contrôlé. Cet équipement doit être installé et utilisé à distance
minimum de 20cm entre le radiateur et votre corps.
This device is intended only for OEM integrators under the following condition:
▪ The transmitter module may not be co-located with any other transmitter or antenna.
If the condition above is met, further transmitter test is not required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes:
▪ Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
Important Note:
If these conditions cannot be met (for example certain laptop configurations or co-
location with another transmitter), then the Canada authorization is no longer considered
valid and the IC ID cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate Canada authorization.
Note Importante:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances,
l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et
Honeywell International Inc
Honeywell Safety and Productivity Solutions
9680 Old Bailes Rd. Fort Mill, SC 29707 United States
l'obtention d'une autorisation distincte au Canada.
End Product Labeling
The end product must be labeled in a visible area with the following: Contains IC: 1693B-
HONST60Q.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
Contient des IC: 1693B-HONST60Q.
Manual Information to the End User
The OEM integrator must be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises
et avertissements comme indiqué dans ce manuel.
Loading...