Page 1
Honeywell
Honeywell
HD73 Series
Operation Manual
Vandal-Resistant
Dome Camera
□igitaL
i^READ AND KEEP THIS
OPERATION MANUAL
cat-OR
www.honeywellvideo.com
Page 2
3-Axís
. User Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Kxplanation of two Symbols
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOLfOM OF THE SYSTEM.
2
« "WARNING-TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"
o
a 2
j
Page 3
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the equipment.
CAUTION • To prevent electric shock and risk of fire hazards:
* Do NOT use power sources except for that specified.
• Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should abide to all local codes.
\Arhen
the equipment is
2
Qt
o
o
u
1
Page 4
. Contents
Thank you for purchasing this COLOR VIDEO CAMERA.
Before using this camera, please read this operation manual carefully to obtain
the best result and keep this manual for future reference.
6
8
8 4
1. SAFETY INSTRUCTIONS
2. PRECAUTIONS
3. FEATURES ............................
4. COMPOSITION .....................
5. INSTALLATION
....................
...................
5 6. CONNECTIONS ............................ .......10
6 7. NAME AND FUNCTIONS
7 8. OPERATING CAMERA
8 9. SPECIFICATIONS
9 10. TROUBLESHOOTING
.........................
...........
................
.................
.......11
.......12
.......34
.......36
Page 5
1. SAFETY INSTRUCTIONS
Read Instructions
Read all of tfie safety and operating Instructions
before using the product.
Retain Instructions
Save this instructions for later use.
Cleaning
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Water and Moisture.
Do not use this product near water or moisture.
(For example, near a bathtub, wash bowl, kitchen
Installation
Do not place this product on an unstable cart, stand,
or table. The product may fall causing serious injury
to a child or adult, and damage to the product.
Use only with a cart or stand recommended by the
manufacturer, or sold with the product.
Mounting should follow the manufacturers Instructions,
and should use a mounting accessory recommended
by manufacturer.
Power source
This product should be operated only from the type
of power source indicated on the marking label,
6
if you are not sure of the type of power supplied to
sink, or laundry tub, in a wet basement, or near a
swimming pooi.etc)
your home, consult your dealer or local power
company.
2
Qt
9
o
u
1
Page 6
3-Axís
2. PRECAUTIONS
Handling
0 Do not disassemble the camera and never touch
parts inside the camera.
O
Do not drop the camera or subject it to shocks
and vibrations to avoid possible damage.
O When attaching or removing the lens, handle
with care in order to that moisture and dust do
not enter the camera.
Installation and storage
O
Do not point the camera at the sun. This could
damage the camera whether it is operating or not.
C
Do not install the camera where the temperature
O Be sure the ambient temperature is less than
40'c in installation intended for long term
continuous operation.
O Avoid installing in a humid or dusty place.
O Avoid installing in places where there are
strong magnetic fields and electric signals.
O Avoid installing in places where the camera
would be subject to strong vibrations.
O
Never expose the camera to rain and water.
9
o
w
1
could exceed the allowable range.
Page 7
3«Axis
3. FEATURES
High Sensitivity 1/3 Inch Sony Super HAD CCD
Min. Illumination (Fl .2, 30 IRE); 0.3 Lux (Color)
0.0 Lux (IR LED On)
Day & Night (ICR)
OSD (On Screen Display)
High Performance Menus For Functions
• Privacy Zone Selectable (4 Programmable Zone)
• Motion Detection Selectable (64 Programmable Zone)
• Sharpness Enhanced Adjustable
• Flickerless Selectable
• Gamma Enhanced Selectable
• BLC Zone Selectable (64 Programmable Zone)
s
D
0£
9
o
u
i
Page 8
3-Axis
4. COMPOSITION
L-Wrench
Guide Pattern
Operation Manual
<
2
C£
o
1
Mounting Screw
J 1—CB
Service Monitor Cable
8
Page 9
5. INSTALLATION
o stick the guide pattern on the wall or ceiling.
Drill four holes according to the guide pattern
O
then Insert anchors into the drilled holes.
Draw out power / video wires to the
O
connecting places.
O Fixed the camera to a celling using four screws.
Adjust desired focus and scene by turning and
O
moving the 3-axis camera bracket by hand.
Q Put the dome cover over the base.
O Fix the dome cover on the base by L-Wrench.
Guide Pattern
Dome Base
Mounting
Screw
lllJ-
<
Dome Cover
L-Wrench
Q
u
1
Page 10
3-Axis
6. CONNECTION
Video Output
X \
GND
2
O
810
1
The wire is polarized. Use 12V DC — power source.
No.
#7 Video Output Yellow I.OVp-p
#2 Power Input Red
Function Terminal Color Remark
12VDC (10V-15V), 360mA (Max)
Page 11
3>Axis
7. NAME AND FUNCTIONS
Camera Lay-out
O Tilt rotation:
O Pan rotation:
o Horizontal rotation:
O Focus handle:
© Zoom handle:
O IR LED(3.8mm~9.5mm): 850nm/ SO^iZOEA), Power Consumption(4.5W)
Adjusting the vertical angle.
Adjusting the horizontal angle,
Adjusting the horizontal position of the screen.
Focus (Far or Near)
Zoom (Tele or Wide)
O Sensor
11
è
2
Oi
O
d
u
Page 12
3-Axis
8, OPERATING CAMERA
SETUP MENU
CAMERA !D • ON • OFF
LENS • MANUAL • VIDEO • DC
SHUHER • AUTO • FLK • FIXED • MANUAL
WHITE BAL. • ATW • AWB • FIXED • MANUAL
FUNCTION • BLC • AGC • PRIVACY
2
O
812
\
• MIRROR • GAMMA • MOTION
ADJUST • CONTRAST • SHARPNESS
• CB_GAIN • CR_GAIN
LANGUAGE • ENGLISH • KOREAN •CHINESE1 •CHINESE2 • JAPANESE
RESET
EXIT
Page 13
O Setting up the Menu
^
Push the Joy stick for one second, and the OSD
appears on the screen. Move the Joy Stick up, down,
left & right to control the OSD functions.
SETUP
• Push and hold MENU button 1 second
to access the setup mode.
Select the status using the
MENU(SET):
SET BY JOY STICK
Service Monitor Connecter:
Use service monitor
connector to set camera angle
& focus when installing.
joystick, (up, down, left, right)
SETUP
CAMERA ID OFF
LENS DC/
SHUTTER FIXED/
WHITE BAL. ATW
FUNCTION
ADJUST
LANGUAGE ENGLISH
RESET
EXIT
/
/
/
13
2
Od
Q
O
u
1
Page 14
O Main Menu - SETUP
1. Press MENU button, then SETUP mode is activated.
• MAIN SETUP menu is displayed on the monitor.
2. Select OSD item using UP, DOWN button.
3. Set details using LEFT, RIGHT button.
4. Select "Exit” and then press the MENU button
SETUP
CAMERA ID OFF
LENS DC/
SHUHER FIXED/
WHITE BAL. ATW
FUNCTION
ADJUST
LANGUAGE ENGUSH
RESET
EXIT
/
/
/
6
2
9
014
o
I
to finish the SETUP (Save and Exit)
Page 15
1) CAMERA ID setup (default setting OFF)
O Main Menu - CAMERA ID
0 Press MENU key in ON
(Access ID setting MODE)
(D Press MENU key in CAMERA ID.
(D Character is changed each lime UR DOWN is
pressed. (Can select up to 63 letters)
@ Press MENU button in / to
exit from ID setup mode
(D Press MENU button in 'C to correct and erase
the chosen entry.
2) POSITION setup. Press POSITION
0 Move the character using UR DOWN, LEFT, RIGHT button.
/
state.
ID SETUP
CAMERA ID
A
POSITION
RETURN
/ c
6
(D Press Menu button to confirm selection of the character.
(D Press Return to go to previous screen. ID Is displayed by pressing EXIT on MAIN MENU.
2
u
i
Page 16
9 Main Menu - LENS
1) LENS setup
® Press LEFT or RIGHT button in LENS on
Main Menu to select the mode to
MANUAL ◄ ► VIDEO ◄ ► DC
LENS DC
i
oc
O
U
^16
Setting Mode : DC
V.
2) DC LENS setup
® Press MENU button in DC to display the
screen on the right side.
0 Use LEFT. RIGHT button to change
BRIGHTNESS(IRIS LEVEL) value.
0 Press MENU button to return to the previous screen.
/
BRIGHTNESS
/ : RETURN
056
1
Page 17
1) SHUTTER setup (for LENS MANUAL)
® Press LEFT or RIGHT button in SHUTTER
to select the mode to
AUTO / ◄ ► FLK ► FIXED ^
O Menu [SHUTTER] - SHUTTER AUTO
◄ ►MANUAL/.
o
^
Setting Mode : FIXED /
SHUTTER AUTO
BRIGHTNESS 056
/ : RETURN
è
ikà
i
17°
y
I
Page 18
O
Menu [SHUTTER] - FIXED Mode Setup
1) FIXED / setup (MANUAL,DC,VIDEO LENS)
® Press MENU button in FIXED /
to display the screen on the right side.
SHUTTER FIXED
t
2
O
0 Press LEFT or RIGHT button in SHUTTER.
Can be set in ([NTSC: 1/60 ~ 1/100,000]
[PAL: 1/50 - 1/100,000]) range.
SHUTTER M: 1/60
/ : RETURN
o
°18
J
Page 19
1) WHITE BALANCE setup
® In WHITE BAL„ press LEFT, RIGHT button
to select the mode you wish to operate
ATW ◄ ► AWB ◄ ► FIXED /
◄ ►MANUAL/.
2) FIXED / setup
® Can set from MODE 1 to MODE 4.
O
Menu [WHITE BAL.j - WHITE BALANCE Mode Setup
AWB FIXED
AWB FIXED : MODE 1
/ : RETURN
3) MANUAL / setup
0 As shown on the lower right picture,
set Red and Blue color value temperature.
<B
Press MENU button in RETURN
to exit from setup mode.
AWB MANUAL
RED 113
BLUE 255
/ : RETURN
1
è
Uri
2
o
19°
y
I
Page 20
O Main Menu - FUNCTION
1) FUNCTION ^ setup
® Press MENU button in FUNTION
to show the OSD display on the right.
FUNCTION
Si
t
6
t
2
9
°20
u
2) Select item using UP, DOWN button.
3) Set details using LEFT, RIGHT button.
4) Click "Return" to go to MAIN SETUP
BLC
AGC ON/
PRIVACY
MIRROR
GAMMA 0.45
MOTION
RETURN
OFF
OFF
OFF
OFF
1
Page 21
1) BLC SETUP MODE
® Press MENU button in BLC ON / ,
to display the screen on the right side.
2) BLC AREA / setup
O Menu [FUNCTION! - BLC 1
BLC SETUP
BLC AREA/
BLC RATIO 16
® Use UR DOWN. LEFT. RIGHT button
to move the AREA setup position.
Set or release BLC AREA
using MENU button.
(D Press MENU button for more than 1 second
to move to BLC AREA MODE.
RETURN
¡5
2
Q
21 ^
u
1
Page 22
O Menu [FUNCTION] - BLC 2
1) BLC AREA MODE 0 Exit from BLC AREA MODE
to move to BLC SETUP MODE screen.
2) BLC OSD description
_
BL (I; A R|E A
a
o
8 22
0
ALL CLEAR -
(BALL SET-Sei
RETURN -
0
EXIT -
Save AREA and return to
BLC SETUP MODE.
Clear all set AREA
all 64 BLC AREA
Return to BLC AREA setup mode.
AL L C L E iR
_
w
___ _____
AL L S E T
RE T U RN
EX E T
.4 .•
__ __ ___ __ _^
I
Page 23
1) BLC RATIO setup (BLC LEVEL value setup) ® Use URDOWN button
to move to BLC RATIO.
O Menu [FUNCTION] - BLC 3
Use LEFT, RIGHT button
to change BLC LEVEL value (0-63)
0;MIN,63:MAX
Press MENU button In RETURN
to move to FUNCTION MODE.
BLC SETUP
BLC AREA/
BLC RATIO
RETURN
w
16
lU
a
Q
23°
Q
y
1
Page 24
O Menu [FUNCTION] - AGC
1) AGC setup
® AGC default setting ON /
<
i
OC
d> Press MENU button in ON /
to display the screen on the right side.
d> Use LEFT. RIGHT button
to adjust AGC GAIN value (0-255)
0:MIN . 255;MAX
(D Press MENU button to return
to the previous screen.
AGC CONTROL
AGC GAIN 095
/ : RETURN
°24
y
1
Page 25
1) PRIVACY setup ® Detault setting OFF - Use LEFT.RIGHT button.
Change setup to ON X mode.
O After ON i/ mode setup. 4 AREA groups are
configured as displayed on the right-side picture.
(I) Press MENU button.
Details of each area is dsplayed.
2) PRIVACY details setup ® Select AREA SEL - PRIVACY 0~3.
AREA STATE - 0-3 AREA ON/OFF
LEFT - Change left portion of each AREA size.
(D RIGHT - Change right portion of each AREA size.
TOP - Change top portion of each AREA size.
BOTTOM - Change bottom portion of each AREA size.
@ COLOR - Change entire color of the AREA (16 COLOR)
O Menu [FUNCTION] - PRIVACY
FUNCTION
BLC ON/
AGC ON/
PRIVACY ON/
MIRROR OFF
GAMMA 0.45
MOTION OFF
RETURN
PRIVACY
AREA SEL AREAO
AREA STATE ON
LEFT 017
RIGHT 058
TOP 020
BOTTOM 055
COLOR 001
RETURN
25°
<
lU
i
Q
u
1
Page 26
O Menu [FUNCTION] - MIRROR
1) MIRROR setup ® MIRROR default setting OFF
ON setting - Use LEFT, RIGHT button.
d) Lett and Right side is switched
as shown on the picture.
FUNCTION
BLC
AGC ON/
PRIVACY
MIRROR
GAMMA 0.45
MOTION OFF
RETURN
OFF
OFF
OFF
Si
t
2
826
J
cm
Page 27
1) GAMMA setup (DEFAULT 0.45) ® In FUNCTION MODE,
use UR DOWN button to select GAMMA.
<B
Use LEFT, RIGHT button
to adjust GAMMA value.
(USER ◄ ► 0.05 ◄ ► 0.10 ◄ ► 0.15-1.0)
O Menu ¡FUNCTION] - GAMMA
FUNCTION
BLC OFF
AGC ON/
PRIVACY
MIRROR OFF
GAMMA 0.45
MOTION OFF
RETURN
OFF
27°
è
8
o
U
I
Page 28
O Menu [FUNCTION] - MOTION
1) MOTION DETECTIVE setup
® DEFAULT value OFF
0 In ON / , press MENU button.
0 Display MOTION details.
2) AREA / setup
® In AREA, press MENU button, (see p.29)
3) MOTION TH. Setup
è
2
§28
I
® Set motion sensitivity 0(MAX)~255(MIN)
4) MOTION TRACE setup
® ON ; Display motion detection AREA.
O
Setting value can be adjusted
using LEFT or RIGHT button.
L
MOTION
AREA/
MOTION TH. 037
MOTION TRACE
RETURN
OFF
I
Page 29
O Menu [FUNCTION] - MOTION AREA 1
1) MOTION AREA setup
® Use UR DOWN, LEFT, RIGHT button
to move AREA setting position.
<D Use MENU button to set and release AREA.
(I) Press MENU button for more than 1 second
to move to MOTION AREA MODE
2) MOTION AREA MODE
® You will return to MOTION AREA MODE
after "Exit" from MOTION AREA MODE.
//—
— —
//—
MO
nor AR :a
ALL CLEJ
ALL
R
SET
—^
—
REl
EXE
URN
r
—y
29°
8
C£
o
u
I
Page 30
O Menu [FUNCTION] - MOTION AREA 2
1) MOTION OSD description ®
ALL CLEAR -
®
ALL SET -
(D
RETURN -
®
EXIT -
Save AREA and return to MOTION SETUP MODE.
Release all set AREA
Set all 64 MOTION AREA.
Return to MOTION AREA Setup Mode.
6
t
2
§30
\
Page 31
1) ADJUST setup
® Press MENU button in ADJUST
<2>
Move to screen on the right side.
O Each LEVEL value can be
adjusted using LEFT, RIGHT button.
L
O Main Menu - ADJUST
ADJUST
CONTRAST
SHARPNESS 12
-----------
083
1
2) CONTRAST setup
® Adjust Y-gain value (0-255)
3) SHARPNESS setup
0 Adjust aperture value (0-31)
4) CB-GAIN setup
0 Adjust COLOR CB-GAIN value (0-255)
5) CR-GAIN setup
0 Adjust COLOR CR-GAIN value (0-255)
CB-GAIN 190
CB-GAIN 205
RETURN
è
(5
s
9
31 °
o
u
1
Page 32
O
Main Menu - LANGUAGE
1) LANGUAGE setup
® DEFAULT value-ENGLISH
UJ
i
(D After selecting LANGUAGE,
change setting using LEFT or RIGHT button.
(D Choose the language mode you
wish to operate in.
P ^ ENGLISH A ► Korean < ► Chinesel < ► Chinese 2 ^ ► Japanese J
SETUP
CAMERA ID OFF
LENS DC/
SHUTTER FIXED/
WHITE BAL. ATW
FUNCTION
ADJUST
UNGUAGE ENGUSH
RESET
EXIT
/
/
/
8
32
1
Page 33
1) RESET
® Select RESET
d> Select YES or NO.
Press MENU button.
The screen on the bottom appears.
® Select YES to reset your camera
to default factory condition
O
Main Menu - RESET
SETUP
CAMERA ID
LENS DC/
SHUTTER HXED/
WHITE BAL. ATW
FUNCTION
ADJUST
LANGUAGE ENGLISH
RESET
EXIT
OFF
/
/
/
LOAD DEFAULT
YES
NO
33°
i
o
u
I
Page 34
9. SPECIFICATIONS
UJ
MODEL ■
Signal System NTSC PAL
Image Sensor 2:1 Interlace Transfer 1/3 Inch Super HAD CCD
Effective Pixels 768(H) x494(V) 752(H) x582(V)
Video Output Composite: I.OVp-p,
Sync. System Internal Sync
Luminance S/N Ratio More than 50dB (AGC OFF)
Horizontal Resolution 530 TV Lines
Min. Illumination (FI .2) 0.3 Lux(30IRE, AGC ON), 0 Lux(IR LED)
Lens DC Auto IRIS Vari-focal (f=3.8~9.5mm)
Focus Manual
Electronic Shutter 1/60-1/100,000 1/50-100,000
HD73 Series
75Q,
Unbalanced
§
8
34
White Balance ATW (1,800'K-10,500"K) / AWB / Fixed / Manual
Camera ID ON/OFF
Language English / Korean / Chinese 1 / Chinese 2 / Japanese
Page 35
BLC, AGC ON/OFF (Level Adjustable)
Day & Night Auto (ICR)
Privacy ON / OFF (4 Programmable Zone)
Mirror ON/OFF (Horizontal)
Gamma User /0.5-1.0 Adjustable
Motion Detection ON / OFF (64 Programmable Zone)
Contrast 0 - 255 (Level Adjustable)
Sharpness 0-31 (Level Adjustable)
Applicable Lens DC Iris
Supply Voltage 12VDC (10V-15V)
Po\wer Consumption Max. 4.5W/360mA
Operating Temperature -10t:- + 50t: (Recommendation; -5t)-+40“C)
Storage Temperature -20ic-+60t;
Dome Size (0) 100 mm
Weight Approx. 844g
35°
è
t
2
O
u
l
Page 36
10, TROUBLESHOOTING
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
Problem Solutions
2
Nothing appears on the
screen.
The image on the screen
is dim.
The image on the screen
is dark.
The camera is not working
properly, and the surface
of the camera is hot.
The image on the screen
flickers.
• Check that the power cord and line connection between the camera and monitor
are fixed properly.
• Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
• Is lens stained with dirt? Clean your lens with soft, clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change the camera position.
• Adjust the lens' focus properly.
• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 759/ Hi-z properly.
• Adjust DC Level, on the OSD menu.
• Check that you have properly connected the camera to an appropriate power source.
• Is the camera facing to direct sunlight or fluoresent lighting?
Change the camera position.
9
836
I
Page 37
Page 38
ICOЮR DOME CAMERA
CO
00
Page 39
co
ч>
1СОЮК DOME CAMERA
Page 40
Loading...