Honeywell HD60 User Manual

COMPOSITION:

Service Monitor Cable

Operation Manual

INSTALLATION:

Stick the guide pattern on the

wall or ceiling.

Drill four holes according to

the guide pattern then insert anchors into the drilled holes.

Draw out power / video wires

to the connecting places.

Fixed the camera to a celling

using four screws.

Adjust desired focus and scene

by turning and moving the 3-axis camera bracket by hand.

Put the dome cover over the

base.

Fix the dome cover on the base

by covering.

You must be fully aware of all the distinctive features and precautions related to this camera before installing it.

Guide Pattern

Mounting Screw

Ceiling

Guide Pattern

Dome Base

Mounting Screw

Dome Cover

NOTE

Insert coin to the side hole and remove the dome cover by twist coin.

DIMENSIONS(mm):

100.0

51.0

37.313.7

130.6

SPECIFICATIONS:

Model

Signal System Scanning System Scanning Frequency (H Scanning Frequency (V Image Sensor Total / Effective Pixels No. S / N Ratio Resolution Video Output Level Lens Focus Sync. System Sensitivity Electronic Shutter White Balance AGC BLC Flickerless Input / Output Connector Power Consumption Dome Size (Ø Weight

Call 1.800.796.CCTV for sales, service and customer support.

) )

)

www.honeywellvideo.com

NTSC PAL

NTSC : 525 Lines PAL : 625 Lines

2 : 1 Interlace

15.734kHz 15.625kHz

59.94Hz 50Hz 1/3" SONY Super HAD CCD

270K / 250K 320K / 290K

More than 48dB (AGC Off)

380 TV Lines

1.0 Vp-p (75 Ohms, composite) Fixed Lens : f=4.0mm, 81

0 Lux, IR LED

1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec.

On / Off (with Slide Switch) On / Off (with Slide Switch)

Power, Video

12VDC (10.8V~15V), 0.4A / 5W (Max)

Approx. 366g

Need Help?

75.7

Manual Internal

Auto

On / Off

100mm

102.0

HD60

Series

Operation

Manual

• 1/3" Sony Super HAD CCD

• 380 TV Lines Resolution

• 4mm Fixed Lens

• Color Day/Night with 24 LEDs

Rev 0 03

P/N:3810-0072H

• Auto White Balance

• AGC, BLC, Flickerless On/Off

• Extra Video Output for Installer

• 3-Axis Camera Construction

• Diameter of Bubble : 100mm

•

READ AND KEEP THIS OPERATION MANUAL

PRECAUTIONS:

Do not install the camera in

extreme temperature conditions.

Do use the camera under conditions where temperatures are within -10°C to 45°C. Be especially careful with ventilation under high temperatures.

Do not install or use the camera

in an environment where the humidity is high.

It can cause the image quality to be poor.

Do not disassemble the camera.

There are no user-serviceable parts inside it.

Do not drop the camera or

subject them to physical shocks.

It can cause malfunctions to occur.

Note

When this camera is installed near wireless communication devices that emits strong electromagnetic field, irregularity such as noise on the monitor may appear.

CONNECTION:

Connecting to Monitor and Power

12VDC Power Type

90º

NAME AND FUNCTION:

Fixed Lens & IR LED Type

Design and specifications are subject to change without notice.

Built-in camera bracket makes it much

easier to rotate in any direction.

3-axis

360º

Tilt rotation: Adjusting the vertical angle.

Pan rotation: Adjusting the horizontal angle.

Horizontal rotation: Adjusting the horizontal position of the screen.

IR LED (4mm Fixed Lens)

Video

(Yellow)

Power - 12VDC (Red)

Video Output

GND

• Power Consumption: 5W

• IR LED Specification: 850nm / 30°(24EA)

• The wire is polarized. • Use 12VDC power source.

No.

Function

Video Output

Power Input

Terminal Color

Yellow

Red

IR LED: 850nm / 30°(24EA)

Sensor

Camera Lay-out

Remark

1.0 Vp-p

12VDC(10.8V~15V), 0.4A/5W(Max)

CAMERA SET-UP:

Fixed Lens & IR LED Type

HEATER

J505

AC 24V

J503

/AUDIO

DC LEVEL

BLC

AGC

OFF

J504

J502

AC24V

J501

VIDEO

31 2

SWITCH

Function Selection Switch:

•FL(Flickerless) ON/OFF

•

AGC(Auto Gain Control) ON/OFF

•

BLC(Back Light Compensation)

ON/OFF

Service Monitor Connecter:

Use service monitor connector to set camera angle & focus when installing.

CAUTION

D/N does not work because the D/N switching function is dependent on the AGC level.

: When AGC is off,

360º

TROUBLESHOOTING:

If you have trouble operating your camera, refer to the following.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

The image does not appear on the screen.

The image on the screen is dim.

The camera does not work properly, the surface of the camera case is hot, and a black line appears on the screen.

The screen blinks a lot.

Check the power source for the monitor and camera and ensure that the voltage and polarity are properly connected and being supplied correctly.

Check if the lens is stained. If dirty, clean the lens with a soft, clean cloth. Adjust the Back Focus of the lens again.

Check if you have connected the camera to a proper power source and If there is no problem with the power, turn the unit off immediately and seek assistance from our Customer Service department.

Check if the camera is pointed toward the sun or a fluorescent lamp. Adjust the angle or location of the camera if too much light is coming into the screen.