Honeywell HD51 User Manual

COMPOSITION:

You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.

DIMENSIONS(mm):

100.0

L-Wrench

Operation Manual

INSTALLATION:

Stick the guide pattern on the

1

wall or ceiling.

Drill four holes according to

2

the guide pattern then insert
anchors into the drilled holes.

Draw out power / video wires

3

to the connecting places.

Fix the camera to a celling using

4

four screws.

Adjust desired focus and scene

5

by turning and moving the
3-axis camera bracket by hand.

Put the dome cover over the

6

base.

Fix the dome cover on the base

7

by L-Wrench.

Service Monitor Cable

Mounting Screw

Ceiling

Guide Pattern

Guide Pattern

Dome Base

Mounting
Screw

Dome Cover

L-Wrench

37.0 47.15

142.4

※󰼿

3/4 JIS B0202-1982

SPECIFICATIONS:

Model

Signal System
Scanning System
Scanning Frequency (H
Scanning Frequency (V
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
BLC
Flickerless
Input / Output Connector
Power Consumption
Dome Size (Ø
Weight

Call 1.800.796.CCTV for sales, service and customer support.

)
)

)

www.honeywellvideo.com

NTSC PAL

NTSC : 525 Lines PAL : 625 Lines

2 : 1 Interlace

15.734kHz 15.625kHz

59.94Hz 50Hz
1/3" SONY Super HAD CCD

410K / 380K 470K / 440K

More than 50dB (AGC Off)

550 TV Lines

1.0 Vp-p (75 Ohms, composite)
Fixed Lens : f=4.0mm

1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec.

On / Off (with Slide Switch)
On / Off (with Slide Switch)

Power, Video

12VDC (10V~15V) / 3W (Max)

Approx. 844g

Need Help?

75.7

Manual
Internal

0.3 Lux

Auto

On / Off

100mm

101.0

• 1/3" Sony Super HAD CCD

• High Resolution:550 TV Lines

• 4 - 9mm DC Vari-focal Auto Iris

• Auto White Balance

• AGC, BLC, Flickerless On/Off

• Extra Video Output for Installer

• 3-Axis Camera Construction

23

/

Rev 0 05

P/N:3810-0055Q

• Vandal-Resistant Dome Housing

• Diameter of Bubble:100mm

HD51

o

t

e

i

l

n

p

s

t

m

i

S

•

a

l

l

Series

Operation

Manual

READ AND KEEP THIS
OPERATION MANUAL

PRECAUTIONS:

!

Do not install the camera in
extreme temperature conditions.

Do use the camera under conditions
where temperatures are within

-20°C to 45°C.
Be especially careful with ventilation
under high temperatures.

!

Do not disassemble the camera.

There are no user-serviceable parts
inside it.

!

Do not drop the camera or
subject them to physical shocks.

It can cause malfunctions to occur.

!

Note

When this camera is installed near
wireless communication devices
that emits strong electromagnetic
field, irregularity such as noise on
the monitor may appear.

CONNECTION:

Connecting to
Monitor and Power

12VDC Power Type

Design and specifications are

NAME AND FUNCTION:

Vari-focal Lens Type

subject to change without notice.

Built-in camera
bracket makes it much
easier to rotate in any
direction.

3-axis

90º

360º

CAMERA SET-UP:

4

5

1

3

2

1

Tilt rotation: Adjusting the vertical angle.

2

Pan rotation: Adjusting the horizontal angle.

3

Horizontal rotation: Adjusting the horizontal
position of the screen.

#

1

Video

(Yellow)

Video Output

GND

#

2

Power - 12VDC
(Red)

• The wire is polarized. • Use 12VDC power source.

No.

Function

#1

Video Output

#2

Power Input

4

Focus handle: Focus (Far or Near)

5

Zoom handle: Zoom (Tele or Wide)

Camera Lay-out

Terminal Color

Yellow

Red

Remark

1.0 Vp-p

12VDC, Max 3W/ 250mA

Vari-focal Lens Type

a

DC Level Adjustment V.R

a

J505

AC 24V

HEATER

J503

/AUDIO

BLC

ON

AGC

OFF

FL

ON

DC LEVEL

ON

J504

J502

AC24V

J501

VIDEO

c

31 2

SWITCH

b

b

Function Selection Switch:

•FL(Flickerless) ON/OFF

•

AGC(Auto Gain Control) ON/OFF

•

BLC(Back Light Compensation)

ON/OFF

c

Service Monitor Connecter:

Use service monitor connector
to set camera angle & focus
when installing.

360º

TROUBLESHOOTING:

If you have trouble operating your camera, refer to the following.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

The image does not
appear on the screen.

The image on the
screen is dim.

The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.

The screen blinks a lot.

Check the power source for the monitor and camera
and ensure that the voltage and polarity are properly
connected and being supplied correctly.

Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.

Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our Customer Service department.

Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.