Page 1
Installer Programming mode User Programming mode
Master User Programming
mode
GKP advanced functionalities
Version V1.0
Author: Florent Busnoult, EMEA Residential Sales Support EMEA, HSF
Date: 15/11/2016
Page 2
© 2015 by Honeywell International Inc. All rights reserved.
9
Recap’
1
Installer
Procedure Sucrebox Domonial
Step by step guide
Set
arming with
identification
Here
Set quick
arming
Here
Associate a TAG to a
user
Here
Change a user’s code
Here
Disable a user’s code
Here
Disable a user
Here
Enable a user
Here
Page 3
© 2015 by Honeywell International Inc. All rights reserved.
9
Recap’
1
Master User
Adjust beep volume
Here
Enable Chime
Here
Disable Chime
Here
Assign TAG
Here
Changing
Code
Here
Disabling
Code
Here
Enable user
Here
Disable user
Here
User
Procedure Sucrebox Domonial
Step by step guide
Page 4
© 2015 by Honeywell International Inc. All rights reserved.
9
Set arming with identification
1
3 - Press “Total arming” button to select function
4 - Press to activate arming with identification (code and TAG)
Installer Programming mode
Enter the installer programming mode
1 - Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 - Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 - Press (⑤ to exit programming and save your changes
All LEDs stop flashing and a double beep is played
Page 5
© 2015 by Honeywell International Inc. All rights reserved.
9
Set quick arming (no identification needed)
1
3 - Press “Total arming” button to select function
4 - Press to activate quick arming
Installer Programming mode
Enter the installer programming mode
1 - Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 - Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 - Press (⑤ to exit programming and save your changes
All LEDs stop flashing and a double beep is played
Page 6
© 2015 by Honeywell International Inc. All rights reserved.
9
Associate a TAG to a user
1
3 - Press “0 to 9” button to select user’s number
4 - Present the TAG to the tag reader
Installer Programming mode
Enter the installer programming mode
1 - Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 - Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 - Press (⑤ to exit programming and save your changes
All LEDs stop flashing and a double beep is played
Page 7
© 2015 by Honeywell International Inc. All rights reserved.
9
Change a user’s code
1
3 - Press “0 to 9” button to select user’s number
4 - Enter new user’s code (4 or 6 digits)
5 - Re-enter new user’s code
Installer Programming mode
Enter the installer programming mode
1 - Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 - Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
6 - Press (⑤ to exit programming and save your changes
All LEDs stop flashing and a double beep is played
Page 8
© 2015 by Honeywell International Inc. All rights reserved.
9
Disable a user’s code (disable the code for a user and keep the
TAG only)
1
3 - Press “0 to 9” button to select user’s number
4 - Enter 0000 (or 000000 if 6 digits)
5 - Press
Installer Programming mode
Enter the installer programming mode
1 - Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 - Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
6 - Press (⑤ to exit programming and save your changes
All LEDs stop flashing and a double beep is played
Page 9
© 2015 by Honeywell International Inc. All rights reserved.
9
Disable a user
1
3 - Press “0 to 9” button to select user’s number
4 - Press to disable the user (code and TAG)
Installer Programming mode
Enter the installer programming mode
1 - Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 - Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 - Press (⑤ to exit programming and save your changes
All LEDs stop flashing and a double beep is played
Page 10
© 2015 by Honeywell International Inc. All rights reserved.
9
Enable a user
1
3 - Press “0 to 9” button to select user’s number
4 - Press to enable the user (code and TAG)
Installer Programming mode
Enter the installer programming mode
1 - Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 - Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 - Press (⑤ to exit programming and save your changes
All LEDs stop flashing and a double beep is played
Page 11
© 2015 by Honeywell International Inc. All rights reserved.
9
Adjust beep volume
1
1 - Press and hold the and keys simultaneously more than 2
seconds to enter user programming mode.
A double beep is played and all LED light on.
2 - Keep pressing the key to select the device that you wish to adjust
(each device will emit a beep when it is selected).
Example: If you want to adjust the beep level for device 2: press the
key twice. Device 2 will emit a beep to confirm its selection.
All LEDs start flashing.
3 - Press a key from to to select the required beep volume (1 =
min, 7 = max).
The device selected will emit a beep at the new level to confirm
the beep volume.
4 - Press the key to exit user programming mode and save you
changes.
5 - After a few seconds, a double beep is played and all LED stop flashing.
User
Programming mode
Page 12
© 2015 by Honeywell International Inc. All rights reserved.
9
To enable/disable chime
1
1 - Press and hold the and keys simultaneously more than 2
seconds to enter user programming mode.
A double beep is played and all LED light on.
2 - Press the key.
A double beep is played and all status LEDs start flashing.
3 - Press the key to enable the chime or the key to disable the
chime.
A long beep is played.
4 - Press the key to exit user programming mode and save you
changes.
5 - After a few seconds, a double beep is played and all LED stop flashing.
User
Programming mode
Page 13
© 2015 by Honeywell International Inc. All rights reserved.
9
To associate a TAG to a user
1
1 - Press and hold the user number “0 to 9” key for 3 seconds (1 is the
master).
A double beep is played and all LEDs light on.
2 - Enter the master code or present the master tag.
A beep is played and all status LEDs start flashing.
3 - Present a new TAG.
The programming mode ends automatically.
4 - After a few seconds, a double beep is played and all status LED stop
flashing.
The operation fails if the TAG is already registered.
If the user already has a TAG, the new one will take its place.
Master User
Programming mode
Page 14
© 2015 by Honeywell International Inc. All rights reserved.
9
To change a user’s code
1
1 - Press and hold the user number “0 to 9” key for 3 seconds (1 is the
master).
A double beep is played and all LEDs light on.
2 - Enter the master code or present the master tag.
A high beep is played and all status LEDs start flashing.
3 - Enter the code for the new user. A high beep is played.
4 - Re-enter new user’s code. A high beep is played.
The programming mode ends automatically.
5 - After a few seconds, a double beep is played and all status LED stop
flashing.
Master User
Programming mode
Page 15
© 2015 by Honeywell International Inc. All rights reserved.
9
To disable a user’s code
1
To disable a user’s code and keep the TAG only:
1 - Press and hold the user number “0 to 9” key for 3 seconds (1 is the
master).
A double beep is played and all LEDs light on.
2 - Enter the master code or present the master tag.
A high beep is played and all status LEDs start flashing.
3 - Change the code to 0000 (or 000000 if 6 digits).
4 - Re-enter the code 0000 (or 000000 if 6 digits).
A high beep is played.
5 - After a few seconds, a double beep is played and all status LED stop
flashing.
Master User
Programming mode
Page 16
© 2015 by Honeywell International Inc. All rights reserved.
9
To disable a user
1
1 - Press and hold user number “0 to 9” key for 3 seconds.
Note: it is not possible to disable the master user.
A double beep is played and all status LEDs light on.
2 - Enter the master code or present the master tag.
A high beep is played and all status LEDs start flashing.
3 - Press the key to disable the user.
The programming mode ends automatically.
4 - After a few seconds, a double beep is played and all status LED stop
flashing.
Master User
Programming mode
Page 17
© 2015 by Honeywell International Inc. All rights reserved.
9
To enable a user
1
1 - Press and hold user number “0 to 9” key for 3 seconds.
A double beep is played and all status LEDs light on.
2 - Enter the master code or present the master tag.
A high beep is played and all status LEDs start flashing.
3 - Press the key to disable the user.
The programming mode ends automatically.
4 - After a few seconds, a double beep is played and all status LED stop
flashing.
Master User
Programming mode
Loading...