Honeywell EnergySmart HZ-789 Instruction Manual
IMPORTANT SAFETY
INSTRUCTIONS
WARNING – READ AND SAVE THESE
OPERATING AND SAFETY INSTRUCTIONS
BEFORE USING THIS HEATER. IF YOU DO
NOT UNDERSTAND THESES INSTRUCTIONS
OR PRODUCT LABELS PLEASE CALL OUR
CUSTOMER REPRESENTIVIES AT (800) 4770457 FOR ASSISTANCE BEFORE USING THIS
PRODUCT.
Warning – Failure to follow any of these safety
instructions could result in fire, injury or death.
YOUR RESPONSIBILITIES
Electrical appliances may expose people to
hazards that can cause severe injury as well
as death. The use of electrical products may
create hazards that include, but are not limited
to, injury, fire, electrical shock and electrical
system damage. These instructions are intended
to provide you with the information you need to
use the product and to avoid such hazards.
When using electrical appliances, basic
precautions should always be followed to
reduce risk of fire, electric shock, and injury
to persons including the following:
1. Warning – Read all instructions before using
this heater.
2. Warning – This heater is hot when in use.
To avoid burns, do not let bare skin touch
hot surfaces. If, provided, use handles
when moving this heater. Keep combustible
materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at
least 3 feet (0.9 m) from the front of the
heater and keep them away from the sides
and rear.
3. Warning – Extreme caution is necessary
when any heater is used by or near children
or invalids, and whenever the heater is left
operating and unattended.
4. Warning – Always unplug heater when not
in use.
5. Warning – Do not operate any heater with
a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged
in any manner. Discard heater or return
heater to authorized service facility for
examination and/or repair.
6. Warning – For residential use only.
7. Warning – Do not use outdoors.
8. Warning – This heater is not intended for
use in bathrooms, laundry areas and similar
indoor locations. Never locate heater where
it may fall into a bathtub or other water
container.
9. Warning – Do not run cord under carpeting.
Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange cord
away from traffic area and where it will not
be tripped over.
10. Warning – Connect to properly grounded
outlets only.
EnErgySmart® ElEctric radiator
(oil-FillEd HEatEr)
HZ-789 Series
The Honeywell Trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.
2
11. Warning – Warning – This heater is for
use on 120 volts. The cord has a plug
as shown in Fig. 1, and an adapter, as
shown, is available for connecting threeblade grounding-type plugs to two-slot
receptacles. The green grounding lug
extending from the adapter must be
connected to a permanent ground such as
a properly grounded outlet box. The adapter
should not be used if a three-slot grounded
receptacle is available. Do not circumvent
the safety features of the grounding-type
plug. Do not modify the power cord.
12. Warning – This heater draws 12.5 amps
during operation. To prevent overloading a
circuit, do not plug the heater into a circuit
that already has other appliances working.
13. Warning – It is normal for the plug to feel
warm to the touch; however, a loose fit
between the AC outlet (receptacle) and plug
may cause overheating and distortion of
the plug. Contact a qualified electrician to
replace loose or worn outlet.
14. Warning – To disconnect the heater, first
turn off the product, then grip the plug body
and pull it from the wall outlet. Never pull by
the cord.
15. Warning – Do not insert or allow foreign
objects to enter any ventilation or exhaust
opening as this may cause an electric shock
or fire, or damage the heater.
16. Warning – To prevent a possible fire, do not
block air intakes or exhaust in any manner.
Do not use on soft surfaces, like a bed, or
where openings may become blocked.
17. Warning – A heater has hot and arcing or
sparking parts inside. Do not use it in areas
where gasoline, paint or flammable liquids
are used or stored.
18. Warning – Use this heater only as
described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.
19. Warning – Always plug heater directly into
a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap
(outlet/power strip).
20. Warning – Never tamper with this product
or attempt to fix it. Any tampering with, or
modification of, this product can result in
serious injury, death, or fire. Risk of electric
shock. Do not open. No user serviceable
parts inside.
21. Warning – Do not remove product labels
that contain warnings or safety instruction.
22. Caution – The output of this heater may vary
and its temperature may become intense
enough to burn exposed skin. Use of this
heater is not recommended for persons with
reduced sensitivity to heat or an inability to
react to avoid burns.
23. Caution – Before cleaning, or storage, or
when not in use, turn the product’s controls
to the OFF position and unplug the heater
from the electrical outlet and allow to cool.
24. Caution – Place the heater on a firm, level,
open surface free from obstructions and
at least 3 feet (0.9 m) away from any
combustible materials. DO NOT use on an
unstable surface such as bedding or deep
carpeting. Be sure the heater is not in a
position where it may be tripped over by
small children or pets. The heater’s rubber
feet will hold it firmly in position.
25. Caution – If your home has aluminum
wiring have a licensed electrician check
your receptacle’s connections. When
using a 1500 watt heater, aluminum wire
connections can cause a safety issue.
26.
SAVE THESE
INSTRUCTIONS
Fig. 1
IMPORTANT SAFETY INSTRUCTIONS REGARDING
THE PLUG ON YOUR PRODUCT
3
WHEEL BASE ASSEMBLY
NOTE: DO NOT OPERATE THE HEATER WITHOUT THE WHEEL BASE
ASSEMBLIES IN PLACE. THE HEATER MUST ALWAYS BE USED IN AN
UPRIGHT POSITION. DO NOT OPERATE THE HEATER IF THE WHEELS
ARE NOT ASSEMBLED CORRECTLY.
• Make sure the heater is unplugged and in the OFF position.
• Turn the heater upside down to install wheels.
• Push wheels into each wheel base pin, until you hear them snap into
position.
• While the heater is still upside-down, position the wheel base assemblies
between the end ns. Attach them to the U-bolts on the heater and
tighten using the wing nuts provided (Fig. 2).
• Turn heater right-side up. Your heater is now ready for use.
If the controls are located at the bottom and the Honeywell logo
is upside down you have installed the wheels incorrectly (Fig. 3).
NOTE: These heaters contain oil that is permanently
sealed and will never require relling or replacing.
NOTE: THESE MODELS MAY TAKE UP TO SEVERAL MINUTES TO REACH NORMAL OPERATIONAL TEMPERATURE.
Be sure the heater is not in a position where it may be tripped over by children or pets.
ABOUT OIL FILLED TECHNOLOGY
Electric Radiators generate heat by passing warmed oil inside
sealed metal columns. Air passes over and through the large
surface area of the metal columns, circulating steady, long-term
heat throughout the room. This type of convection heating
technology is quiet and provides gradual, ecient heating.
For best results, place heater on the oor to create
warming room convection and allow heater to run for
10-15 minutes to reach maximum heat output.
SET UP
Place the heater on a rm, level surface free from obstructions, and at least 3ft. (0.9m) away from any wall or combustible material.
Do NOT use on an unstable surface such as bedding or deep carpeting.
MOVING THE HEATER
• Turn o the heater.
• Allow it to cool for ten minutes.
• This heater is equipped with a large luggage-style handle and easy glide caster wheels for your convenience.
• Unplug heater and simply push the handle up in an upright position and pull to move.
• Place the heater on a rm, level surface free from obstructions, and at least 3ft. (0.9m) away from any wall
or combustible material.
Fig. 2
(Bottom of Unit)
Wheel Base
Wheel Base Pin
Wing Nuts
U-bolts
Fig. 3
Correct Incorrect
4
HZ-789 OPERATION
NOTE: NEVER LEAVE AN OPERATING UNIT UNATTENDED.
With the Power Button (
) in the OFF position, plug the heater into a 120V outlet.
DO NOT FORCE THE THREE PRONG SUPPLY CORD INTO THE OUTLET; it will only t
one way.
Turn the heater on by pressing Power Button (
) button, (Fig. 4). The heater will
default to the Constant HI mode and the Current Temp Indicator will display the
current room temperature.
As the heater warms up, the oil in the metal columns may naturally expand and
make a slight ticking sound. This is normal and will stop once the oil has reached
the optimal temperature.
The Energy Usage Indicator will display the power consumption used by the heater.
• If HI, the heater is drawing 1500 watts to quickly warm the room
• If LO, the heater is drawing 900 watts to slowly warm the room or maintain the
temperature.
• If STAND BY, the heater is drawing no power as the room has reached the Desired
Temperature. At this point, the heater is most ecient and is drawing only a few
watts of energy while in STAND BY mode.
To set the heater, (Fig. 5) the digital control is equipped with two (2) modes:
Constant Heat Mode - there are two (2) heat settings
1 For Constant Low, press SET to LO; this setting uses 900 watts of power
2 For Constant High, press SET to HI; this setting uses 1500 watts of power
NOTE: Because the LO setting does not require as much electricity to operate,
it is more energy ecient and may be a better option if you are concerned about
saving energy.
EnergySmart® Mode - A smart thermostat that helps you save energy. Press SET to
choose from four (4) comfort settings of 65°F (18°C), 70°F (21°C), 75°F (24°C), 80°F
(27°C). This is your desired room temperature. The EnergySmart® thermostat will
automatically select the appropriate power level to best accommodate your Desired
Temperature. As the air temperature (Current Temp) in the room approaches the
Desired Temperature, the heater will automatically lower the power consumption
to provide consistent warmth without wasting energy.
The Current Temp Indicator will display the current room temperature.
NOTE: In the EnergySmart® mode, the Energy Usage Indicator will display what
power consumption the heater has automatically selected to eciently meet your
Desired Temperature.
• To override the EnergySmart® function, turn the heater OFF (
) or press SET to
choose a Constant Heat mode.
• To set the Timer, (Fig.6) press the (
) button to select 2, 4, 6, 8, 10 or 12 hour
setting. The heater will run for that chosen period in the selected mode and
automatically shut o after the desired time has passed. Timer will count down
to display the remaining time.
Heat Setting
Control
Fig. 5
Fig. 6
Timer
Current
Temp
Indicator
Energy Usage
Indicator
Fig. 4
Power
Button
Constant
Heat
Modes
EnergySmart®
Modes
5
SAFETY FEATURES
TROUBLESHOOTING
CLEANING AND STORAGE
The EnergySmart® Electric Radiator is equipped with several devices and features for added protection:
• Tip Over Auto Shut O – 4-way tip over shuto - disables heater if tipped front, back or side to side directions.
• A high temperature safety control prevents overheating.
• This heater is also equipped with a thermal cut-o fuse that will permanently shut down the heater should it operate at a
higher than normal temperature.
If your EnergySmart® Electric Radiator shuts o unexpectedly or fails to operate,
one of your heater safety features may have been activated to prevent overheating.
• Be sure the heater is plugged in and that the electrical outlet is working.
• Check your temperature setting. The heater may simply be o because you have
reached your desired temperature setting or your timer setting may have elapsed.
• Make sure your heater is assembled correctly. If your heater is assembled and
operating incorrectly it could result in a burning odor and smoke (Fig. 7).
For more troubleshooting tips, visit our website at: www.kaz.com
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST
OR SEE YOUR WARRANTY. DO NOT RETURN THE HEATER TO THE ORIGINAL PLACE OF
PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY
VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE PRODUCT OR PERSONAL INJURY. IF
YOU HAVE ANY QUESTIONS REGARDING THIS HEATER, PLEASE CALL OR WRITE:
Kaz USA, Inc. • Consumer Relations Department 250 Turnpike Road, Southborough, MA 01772 Toll Free: 1-800-477-0457
E-mail: consumerrelations@kaz.com
We recommend that the EnergySmart® Electric Radiator be cleaned at least once a month and before o-season storage.
• Turn the heater OFF and unplug it. Allow it to cool completely.
• Use only a dry cloth to clean the external surfaces of the heater. DO NOT USE WATER, WAX, POLISH,
OR ANY CHEMICAL SOLUTION.
• Before storing, wrap the cord around the cord wrap on the unit, place it in its original box and store in a cool, dry area.
Operation Cost* To estimate the cost to operate this heater, multiple the watts used times .001 to convert into a kilowatts measure
and multiple by your local kilowatt electric rate for however long you run the heater. For example, if your electric rate is $.1196**
per kilowatt hour and you ran this heater in constant high mode (1500 watts) for 4 hours, it would cost you $.71 cents to run the
heater (1500 watts x 4 hours x.001) x .1196kwp = .71 cents)
NOTE: Because the (LO) or EnergySmart® Setting does not require as much electricity to operate, they are more energy ecient and
may be better options if you are concerned about the amperage draw on a circuit when the heater is on the (HI) setting.
*Calculation (Total Wattage x .001) x Cost per Kilowatt Hour = Cost to operate
**Average Retail Price of Electricity to Ultimate Customer by End-Use, US Energy Information Administration, August 11, 2010
ELECTRICAL RATINGS
This product is rated 12.5 Amps
(1500 Watts) at 120 VAC.
PRODUCT SPECIFICATION
Model HZ-789
Amps 12.5
Unit Voltage 120V, 60Hz
Max Watts 1500
Max BTUs 5118
Unit dims 13.6” L x 9.5” W x 25.2” H (assembled)
Fig. 7
Correct Incorrect
6
You should rst read all instructions before attempting
to use this product.
A. This 3 year limited warranty applies to repair or
replacement of product found to be defective in material
or workmanship. This warranty does not apply to damage
resulting from commercial, abusive, unreasonable use or
supplemental damage. Defects that are the result of normal
wear and tear will not be considered manufacturing defects
under this warranty.
KAZ USA, INC. IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
Some jurisdictions do not allow the exclusion or limitation
of incidental or consequential damages or limitations on
how long an implied warranty lasts, so the above limitations
or exclusions may not apply to you. This warranty gives you
specic legal rights, and you also may have other rights
which vary from jurisdiction to jurisdiction. This warranty
applies only to the original purchaser of this product from
the original date of purchase.
B. At its option, Kaz USA, Inc. will repair or replace this product
if it is found to be defective in material or workmanship.
Thereafter, while within the warranty period defective
product may be returned to Kaz USA, Inc.
C. This warranty does not cover damage resulting from any
unauthorized attempts to repair or from any use not in
accordance with the instruction manual.
D. Return defective product to Kaz USA, Inc. with a brief
description of the problem. Include proof of purchase and
a $10 US/$15.50 CAN check or money order for handling,
return packing and shipping charges. Please include your
name, address and a daytime phone number.
You must prepay shipping charges. We suggest having
tracking or delivery conrmation. Send to:
I
n U.S.A.
Kaz USA, Inc.
Attn: Returns Department
4755 Southpoint Drive
Memphis, TN 38118
USA
In Canada:
Kaz Canada, Inc.
Attn: Returns Department
510 Bronte Street South
Milton, ON L9T 2X6
Canada
Please go to www.kaz.com and register your product under
the Customer Care Center and receive product information
updates and new promotional oers.
3 YEAR LIMITED WARRANTY
©2012 Kaz USA, Inc. All Rights Reserved.
US Patent No. 7,403,702
P/N: 31IMZ789190
Loading...