Honeywell 025010 Users Manual

Page 1
INNCOMȱPCȬ502.2ȱDatasheetȱ
0-40,0-95%RH
Overviewȱ
The INNCOM PC-502.2 wall mounted module can be used to expand the range of a Layer-2 RF network or provide the protocol gateway from INNCOM S5-bus to Layer-2 RF protocol.
In the Layer-2.2 802.15.4 Zigbee 2006 mesh network, the PC-502.2 is designed to patch areas within the network where signal strength is lost due to distance limitations or interference. It also serves to create multiple pathways, increasing the redundancy of the mesh communications to ensure maximum network reliability.
Featuresȱ
x Small wall mountable form factor x 2.4Ghz IEEE 802.15.4 compliant RF transceiver (CC2430 radio
core)
x Medium and long range variants available x Industrial temperature ratings 0-65 degrees C x FCC Part 15b listed
Specificationȱ
Parameterȱ PCȬ502.2ȱ
Figure 1 PC-502.2
RF Data Rate 250kbps Antenna Type SMT Indoor Range 100ft Outdoor/ RF line-of-sight range 1000ft+
Transmit Power 10mW (+18dBm) Receive Sensitivity -94.6dBm Frequency Band 2.405-2.475GHz Encryption AES-128 Protocol 802.15.4 Frequency Channels 15 Input Voltage 12VDC Current Consumption 100mA (Peak) Operating Ambient Temperature 40 ° C LED /Switch Reset indication, blinks when unit is connected to an RF
network. Rapid blink during binding association.
10dBm
Page 2
INNCOM PC-502.2 Datasheet Page | 2
Ranges are determined by performing an RF link quality test using e528.3G thermostats as the transmitter and the PC-502.2 as the receiver. The maximum distance threshold is based on a 95% overall link quality. Outdoor ranges were conducted in a low noise, free air environment. Indoor ranges are for reference. Indoor ranges are affected by the ambient environmental noise floor and building construction materials.
NetworkȱTopologyȱ
Figure 2 PC-502 Layer-2 Topology
In this application, the PC-502.2 in participation with the e529.RF provides the Layer-1 to Layer-2 RF Bridge where both wireless in-room and wireless back-end networking are required. The PC-
502.2 can also patch areas within the Layer-2 network where signal strength is lost due to distance limitations or interference.
Page 3
INNCOM PC-502.2 Datasheet Page | 3
run
Commissioningȱ
The PC-502.2 must be bound to the controlling device (e.g., the E529.RF in Figure 2 above) to receive configuration information. On the E529.RF in service mode
x Open the
x Set the value to 3 and press Display x When Display is pressed, the e529.RF sends Layer-2 configurations to the PC-502.2. (This
function does not offer any feedback on the screen so it is recommended that the Display button be pressed 3 or 4 times to ensure configuration.)
menu and press Off/Auto
Safety/Regulatoryȱ
Parameterȱ Conditionȱ Statusȱ
FCC Part 15b 02-9994 is FCC listed. 02-9894, and 02-9927 FCC listings are pending.
PCȬ502.2ȱDimensionsȱ
ȱ
HeaderȱandȱConnectionsȱ
H3ȱ(InȱSystemȱProgramming)ȱ
Pinȱ Functionȱ Typeȱ Minȱ Maxȱ
1-8 Programming - - -
H4ȱ/ȱH5ȱ(S5ȬbusȱIn/Out)ȱ
Pinȱ Functionȱ Typeȱ Minȱ Maxȱ
1-GND Common - - - 2-12VDC Input voltage In 11.75 12.25
Page 4
INNCOM PC-502.2 Datasheet Page | 4
3-S5-bus Multi-drop In/Out -
H6ȱ(SystemȬ5)ȱ
Pinȱ Functionȱ Typeȱ Minȱ Maxȱ
1-GND Common - - - 2-12VDC Input voltage In 11.75 12.25 3-S5-bus Multi-drop In/Out - 4–InOut1 TTL In/Out - 5-InOut2 TTL In/Out -
3-pin to 3-pin harness for 12VDC and S5bus connection
OrderingȱInformationȱ
PartȱNumberȱ OPNȱ Descriptionȱ
01-5010.2 PC-502.2 PC-502 with 02-9894 20db Radio
DocumentȱRevisionȱHistoryȱ
Revisionȱ DateȱIssuedȱ ȱReasonȱ
0.1 27-Mar-2009 FCC for PC-502
0.2 31-Mar-2009 Edited for content and format
1.0 07-Apr-2009 Released
Page 5
Warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20 cm between the radiator& your body
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Loading...