Honda Power Equipment HS828 User Manual
Thank you for purchasing a Honda snowblower.
This manual covers the operation and maintenance of the HS828
snowblower.
All information in this publication is based on the latest product informa-
tion available at the time of approval for printing.
Honda Motor Co., Ltd. reserves the right to make changes at any time
without notice and without incurring any obligation.
No part of this publication may be reproduced without written permission.
This manual should be considered a permanent part of the snowblower
and should remain with the snowblower if it is resold.
READ THIS OWNER’S MANUAL CAREFULLY. Pay special attention to
these symbols and any instructions that follow:
m
m
(1
NOTE: Gives helpful information.
Honda snowblowers are designed to give safe and dependable service if
operated according to instructions. Operating this snowblower requires
special effort on your part to ensure your safety and the safety of others.
m
or property damage. Read and understand this Owner’s Manual before
operating this snowblower.
If a problem should arise, or if you have any questions about your
snowblower, consult an authorized Honda snowblower dealer.
- Indicates serious injury or death WILL result if instructions are not followed,
- Indicates a strong possibility that serious injury or death
could result if instructions are not followed.
- Indicates a possibility that minor injury can result if
instructions are not followed.
- Indicates that equipment or property damage can result
if instructions are not followed.
Using this product for a purpose not intended may cause injury
HONDA MOTOR CO., LTD. 1991, ALL RIGHTS RESERVED
1
CONTENTS
SAFETY
1.
COMPONENT IDENTIFICATION ...........................................
2.
3.
CONTROLS
PRE-OPERATION CHECK ....................................................
4.
STARTING THE ENGINE .....................................................
SNOWBLOWER OPERATION ...............................................
65:
STOPPING THE ENGINE .....................................................
7.
MAINTENANCE ................................................................
8.
TRANSPORTING ...............................................................
9.
STORAGE ........................................................................
10.
TROUBLESHOOTING .........................................................
11.
SPECIFICATIONS ..............................................................
12.
WARRANTY SERVICE
13.
...........................................................................
......................................................................
........................................................
3
7
8
16
21
26
31
33
40
42
45
46
47
2
SAFETY LABEL LOCATIONS
Read these labels before operating the snowblower.
1. SAFETY
3
To ensure safe operation
l Always make a pre-operation check (pages 16 thru 20) before you start
the engine. You may prevent an accident or equipment damage.
l Honda snowblowers are designed to give safe and dependable service
if operated according to instructions. Read and understand this
Owner’s Manual before operating the snowblower. Failure to do so
could result in personal injury or equipment damage.
l Before operating the snowblower, inspect the area in which you are go-
ing to clear snow. Remove debris and other obstacles the snowblower
might strike or throw, as that may cause injury or damage to the
snowblower.
l Inspect the snowblower before operating it. Repair any damage and
correct any malfunction before operation. If you hit an obstacle while
operating the snowblower, stop the engine immediately, and check for
damage. Damaged equipment may increase the possibility of injury during operation.
l Do not use the snowblower when visibility is poor. Under conditions of
poor visibility, there is a greater risk of striking an obstacle or causing
injury.
l Never use the snowblower to clear snow from a gravel road or
driveway, as rocks may be picked up and ejected. They may cause injury to bystanders.
4
Adjust the snow discharge chute to avoid hitting the operator,
bystanderds, windows, and other objects with ejected snow. Stay
clear of the snow discharge chute while the engine is running.
Children and pets must be kept away from the area of operation to
avoid injury from flying debris and contact with the snowblower.
To avoid overturning, be ‘careful when changing the direction of the
snowblower while operating it on a slope. Do not use the snowblower
to remove snow from roofs. The snowblower may overturn on steep
slopes if left unattended, causing injury to the operator or bystanders.
Know how to stop the snowblower quickly, and understand the operation of all controls.
Never permit anyone to operate the snowblower without proper instruction. If people or pets suddenly appear in front of the snowblower
while it is in operation, immediately release the auger and drive clutch
levers to stop the snowblower and avoid possible injury from rotating
auger blades.
If the snow discharge chute becomes clogged, stop the engine and use
a wooden stick to unclog it. Never put your hand into the snow
discharge chute while the engine is running; serious personal injury
could result.
5
l Gasoline is extremely flammable and is explosive under certain condi-
tions. Do not smoke or allow flames or sparks where the snowblower is
refueled or where gasoline is stored. Refuel in a well-ventilated area
with the engine stopped. Do not overfill the fuel tank, and make sure
the filler cap is closed securely after refueling.
l Never run the engine in an enclosed or confined area. Exhaust contains
poisonous carbon monoxide gas; exposure can cause loss of consciousness and may lead to death.
l The muffler becomes very hot during operation and remains hot for a
while after stopping the engine. Be careful not to touch the muffler
while it is hot. Let the engine cool before storing the snowblower
indoors.
NOTE: While operating the snowblower, hold the handle firmly, and walk;
don’t run. Wear suitable winter boots that resist slipping.
6
SNOW DISCHARGE
CHUTE
AUGER
2. COMPONENT IDENTIFICATION
JGER CLUTCH LEVER
CHUTE GUIDE
I c\,cm \
LE” C”
Al
\ I
\
DRIVE CLUTCH
/LEVER
‘SHIFT LEVER
THROTTLE LEVER
,AC STARTER BUTTON
CAP
ENGINE SWITCH
TRANSMISSION
FLUID RESERVOIR
FUEL VALVE
CHUTE CR
FOOT PEDAL
FRAME SERIAL NUM
4
-\
TRANSMiSSlON
\
RELEASE LEVER ENGINE SERIAL NUMBER
SKID PLATE
\
Record the frame and engine serial numbers for your reference. Refer to
the serial numbers when ordering parts, and when making technical or
warranty inquiries (see page 47).
Frame serial number:
Engine serial number: GC04-
7
3. CONTROLS
Engine switch
Use the engine switch to turn the ignition system ON for starting, and to
STOP the engine.
---+/I
STOP (OFF) (ON)
ENGINE StilTCH
A. C. starter button
Push the starter button to operate the electric starter.
STARTER BUTTON
Fuel valve
The fuel valve opens and closes the fuel line leading from the fuel tank to
the carburetor. Make sure that the valve is positioned exactly at either the
ON or OFF position.
ON
m
valve to OFF to prevent possible fuel leaks; spilled fuel or fuel vapor may
ignite.
Before transporting the snowblower, be sure to turn the fuel
8
Fuel gauge
The fuel gauge indicates the amount of fuel in tlie tank.
When the fuel gauge needle enters the “E” renge, refill the tank as soon as
possible.
FUEL GAUGE
Chute crank
Use the chute crank to turn the snow discharge chute right or left.
To throw snow
to the left
9
To throw snow to the right
9
Starter grip
Pull this grip to start the’ engine.
STARTER GRIP
Throttle lever (Engine speed)
The throttle lever controls engine speed from SLOW to FAST; it will stay in
any designated position. Set the lever to CHOKE when the engine is cold.
SLOW
THROTTLE L
10
Shift lever
The shift lever selects FORWARD (F), NEUTRAL (N), or REVERSE (RI
hydrostatic transmission drive.
The shift lever also controls the transmission drive ratio; moving the lever
farther from NEUTRAL increases drive speed. While clearing snow, use
the shift lever to control drive speed, so you can leave the throttle lever in
the FAST position for best snow-clearing performance.
REVERSE
SHIFT LhER
Chute guide
The chute guide controls the snow discharge angle.
HIGH AND FAR
LOW AND NEAR
CHUTE GUIDE
LEVER
HIGH AND FAR
NEAR
Drive clutch lever and auger clutch lever
Use these controls to engage the snow blowing mechanism and/or the
drive mechanism.
DRIVE CLUTCH LEVER
/
Squeeze to engage the
AUGER CLUTCH LEVER
Squeeze to engage
the snow blowing
mechanism.
drive machanism.
NOTE: When both levers are squeezed, the drive clutch lever locks the
auger clutch lever down. Releasing the drive clutch lever then unlocks and
releases the auger clutch lever.
12
Roth levers squeezed
DRIVE CLUTCH
EVER
The auger clutch lever
remains locked down so
long as one hand continues
to squeeze the drive clutch lever.
Skid plate, Scraper
Adjust the skid plates for the auger ground clearance best suited to your
snow removal conditions.
m
OFF position and disconnect the spark plug cap.
To prevent accidental starting, turn the engine switch to the
1. Place the snowblower on a level surface and set the height adjustment
pedal in the middle position.
2. Move the skid plates up or down to obtain the desired auger ground
clearance.
For ordinary snow:
For finishing:
4-8 mm (0.16-0.31 in)
O-5 mm (O-0.20 in)
For use on uneven surfaces: 25-30 mm (0.98- 1 .18 in)
3. Adjust the scraper ground clearance to 2-4 mm (0.08-0.16 in).
(0.08-0.16 in)
SKID PLATE
NOTE: Adjust the skid plates equally on both sides.
Be sure to tighten the skid plate and scraper bolts securely after making
adjustments.
(1
the auger ground clearance set for hard snow or surfaces. This may cause
serious damage to the snow throwing mechanism.
Do not use the snowblower on rough or uneven surfaces with
13
Foot pedal
Use the pedal for adjusting the height and angle of the machine in relation
to the tracks.
1. Hold the handles and step on the pedal.
2. Raise or lower the machine to the desired position and release the
pedal.
LOW
: Hand snow or fine finish
MIDDLE: Normal use
HIGH
: Deep snow or for transporting the snowblower.
FOOT PEDAL
HIGH
MIDDLE
LOW
14
Loading...