Honda Power Equipment BC2401IC, BC2401HE, HRR216VKA User Manual

ACCESSORIES

NUT REPLACEMENT KIT

P/N 500208.

To replace stripped or

damaged insert nuts in

engine base.

BLADE BC2401

P/N 500210.

Original Equipment Blade

for replacement.

BELT TRACTION DRIVE

P/N 500119.

Traction Drive Belt

for BC2401

BELT BLADE DRIVE

P/N 500237.

Blade Drive Belt

for BC2401

BLADE HIGH LIFT

BC2401

P/N 500102.

Optional blade for

replacement

Thank You for Selecting

The Powerful BC2401 SELF-PROPELLED BRUSH CUTTER

Operator Owner's Manual

BC2401IC, BC2401H, BC2401HE

ENGINE: H.P. 10.5 (7.83 kW) 11 (8.20 kW) 11 (8.20 kW) ENGINE: TYPE B&S HONDA HONDA ENGINE MODEL NO: 28B702118-E1 GXV340K1DX3 GXV340K1DE33 ENGINE: FUEL CAP. 3.0 qt. (2.84 L) 2.3 qt. (2.18 L) 2.3 qt. (2.18 L) ENGINE: OIL CAP. 1.34 qt. (1.41 L) 1.20 qt. (1.13 L) 1.20 qt. (1.13 L) WEIGHT: UNIT 282# (128.5 kg) 278# (126.1 kg) 282# (127.9 kg) WEIGHT: SHIPPING 310# (141.3 kg) 306# (138.8 kg) 310# (140.6 kg) ENGINE WEIGHT: 66.0# (30.0 kg) 70.5# (32.0 kg) 72.5# (32.9 kg) MAX. OPERATING SLOPE 15° 20° 20°

UNIT SIZE: OVERALL LENGTH: 82.5"(2.09 m) OVERALL WIDTH 32.0" (0.81m) OVERALL HEIGHT43" (1.09m)

Specifications

BC2401IC BC2401H BC2401HE

Part No. 500264 Form No. F101001APage 1 of 12

IN THE INTEREST OF SAFETY

BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & ENGINE MANUAL.”

THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.

WARNING: The Engine Exhaust from this product contains chemicals known

to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING: DO NOT

1. DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

2. DO NOT place hands or feet near moving or rotating parts.

3. DO NOT store, spill or use gasoline near an open flame, or devices such as a stove, furnace, or water heater which use a pilot light or devices which can create a spark.

4. DO NOT refuel indoors where area is not well ventilated. Outdoor refueling is recommended.

& /or damage to unit.

13. DO NOT tamper with governor springs, governor links or other parts which may change the governed engine speed.

14. DO NOT tamper with the engine speed selected by the engine manufacturer.

15. DO NOT check for spark with spark plug or spark plug wire removed. Use an approved tester.

16. DO NOT crank engine with spark plug removed. If engine is flooded, place throttle in “FAST” position and crank until engine starts.

17. DO NO T strike flywheel with a hard object or metal tool as this may cause

5. DO NOT fill fuel tank while engine is running. Allow engine to cool for 2

flywheel to shatter in operation. Use proper tools to service engine.

minutes before refueling. Store fuel in approved safety containers.

18. DO NOT operate engine without a muffler. Inspect periodically and replace, if

6. DO NOT remove fuel tank cap while engine is running.

7. DO NOT operate engine when smell of gasoline is present or other explosive conditions exist.

8. DO NOT operate engine if gasoline is

necessary. If engine is equipped with muffler deflector, inspect periodically and replace, if necessary, with correct deflector.

19. DO NOT operate engine with an accumulation of grass, leaves, dirt or other combustible material in the muffler area.

spilled. Move machine away from the spill and avoid creating any ignition until the gasoline has evaporated.

20. DO NOT use this engine on any forest covered, brush covered, or grass covered unimproved land unless a spark arrester is

9. DO NOT transport unit with fuel in tank.

installed on the muffler. The arrester must be maintained in effective working order by

10. DO NOT smoke when filling fuel tank.

11. DO NOT choke carburetor to stop engine. Whenever possible, gradually reduce engine speed before stopping.

12. DO NOT run engine at excessive speeds. This may result in injury

TABLE OF CONTENTS

SAFETY INSTRUCTIONS GENERAL SAFETY ASSEMBLY LIT. BAG & CONTROLS LABELS OPERATION MAINTENANCE PARTS DRAWING & LIST TROUBLESHOOTING WARRANTY PROCEDURE

Part No. 500264 Form No. F101001A

2 3 3 4 4

5, 9

10 - 12

6 - 8

12 12

the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal

7 8

TEMPERATURE:

WIND SPEED: WIND DIRECTION:

OPERATOR

HUMIDITY:

BAROMETRIC PRESSURE:

SOUND

SOUND TESTS

Sound tests conducted were in accordance with 79/113/EEC and were performed on 05/19/ 95 under the conditions listed:

GENERAL CONDITION:

Page 2 of 12

Sunny

62 °F (16.7 °C)

5 MPH (8 kmh)

South

67%

30.06" Hg (763mm Hg)

laws apply on federal lands.

21. DO NO T touch hot muffler, cylinder, or fins because contact may cause burns.

22. DO NOT run engine without air cleaner or air cleaner cover.

23. DO NOT operate during excessive vibration!

24. DO NOT leave machine unattended while in operation.

25. DO NOT park machine on a steep grade or slope.

WARNING: DO

1. ALWAYS DO remove the wire from the spark plug when servicing the engine or equipment TO PREVENT ACCIDENTAL STARTING.

2. DO keep cylinder fins and governor parts free of grass and other debris which can affect engine speed.

3. DO pull starter cord slowly until resis- tance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

4. DO examine muffler periodically to be sure it is functioning effectively. A worn or leaking muffler should be repaired or replaced as necessary.

5. DO use fresh gasoline. Stale fuel can gum carburetor and cause leakage.

6. DO check fuel lines and fittings frequently for cracks or leaks. Replace if necessary

7. Follow engine manufacturer operating and maintenance instructions.

8. Inspect machine and work area before starting unit.

VIBRATION

VIBRATION LEVEL 1.1g

Vibration levels at the operators handles were measured in the vertical, lateral, and longitudinal directions using calibrated vibration test equipment. Tests were performed on 05/19/95 under the conditions listed:

GENERAL CONDITION:

TEMPERATURE:

WIND SPEED: WIND DIRECTION: HUMIDITY:

BAROMETRIC PRESSURE:

72 °F (22.2 °C)

5 MPH (8 kmh)

30.06" Hg (763mm Hg)

Sunny

S.W.

67 %

GENERAL SAFETY

For your safety and the safety of others, these directions should be followed:

Do not operate this machine without first reading owner's manual and engine manufacturer's manual.

Use of Ear Protection is recommended while operating this machine.

Use of Eye and Breathing protection is recom mended when using this machine.

·DO NOT place hands or feet beneath cutting deck, near

debris outlet or near any moving parts.

·DO NOT start engine or operate unit with bystanders in or near the work area.

·DO NOT start or operate machine with blade or drive clutch engaged.

ASSEMBLY

Read all safety and operating instructions before assembling or starting this unit.

PUT OIL IN ENGINE BEFORE STARTING.

DISCONNECT SPARK PLUG WIRE BEFORE ASSEMBLING UNIT.

Your Billy Goat Brush Cutter is shipped from the factory in one carton, completely assembled except for the upper handle, and front guard bar.

·DO NOT operate during excessive vibration.

·DO NOT perform any maintenance or inspection until engine has

been turned off and has come to a complete stop, and the spark plug has been removed

·DO NOT operate machine with guards removed.

·DO NOT use this machine for cutting areas containing rock,

glass, string like material, wire, rags, cans, metal, or other nonorganic material.

·DO NOT operate this machine on slopes greater than specified on page 1.

·DO NOT operate machine near any hot or burning debris, or any toxic or explosive material.

·DO NOT allow children to operate this equipment.

1. REMOVE unit from carton and allow upper handle (item 40) to lay on ground behind unit. Set guard bar(Item 31) to the side for now.

2. REMOVE hardware items 115, 117, 141, 143, & 144 from temporary storage positions on lower handle (items 51, & 52).

3. ATTACH upper handle to lower as shown below, and securely tighten all fasteners. For easy alignment of handles during installation, loosen the four screws that secure the lower handles. Line up and hand tighten all handle hardware before final tightening. Note: Be sure the engine starter rope is properly installed in the starter rope guide (item 145) before tightening the corresponding fasteners.

4. REMOVE hardware items 102, 103, 117, 119, 124, 141, & 152 from temporary storage positions on deck and skid assy at front of unit (items 2, 155, & 156)

5. ATTACH guard bar(Item 31) to deck as shown below. Install the center bolts(Item 153) first, and install the bolts that fasten through the sides of the deck last. Securely tighten all fasteners. Note: Hardware items 117, 119, & 141 are used to secure both the front skid attachment and the sides of the guard bar. Be sure both are securely attached.

6. CONNECT spark plug wire to spark plug.

PACKING CHECKLIST

These items should be included in your carton. If any of these parts are missing, contact your dealer.

Part No. 500264 Form No. F101001APage 3 of 12

Literature

Assy

Engine

Manual

Per Model

Handle Upper Assembly 500256

Bar Support WA 500235

Literature Assy 500263

Briggs & Stratton

Honda(English)

Honda W/Electric Start (English)

12 13

LITERATURE ASSY P/N 500263

CONTROLS

Literature Checklist

Throttle Control

BRIGGS & STRATTON

Briggs engines have a choke

type carburetor that is operated by moving the throttle control to the full start position. See STARTING section, see page 5.

Owner's

Manual

Warranty

Card

EU Declaration

of Conformity

& EU

Distributor List

Owner's

Manual

500264

Warranty

Card

400972

EU Declaration

of Conformity &

EU Distributor

List 500265

Ty Wrap 900407

Qty: (4)

These labels should be included on your Brush Cutter. If any of these labels are damaged, replace them before putting this equipment into operation. Item and part numbers are given to help in ordering replacement labels..

Label Do Not Fill While Engine Is Hot Item 63 Part No.400268

INSTRUCTION LABELS

Label Ear Eye Breathing Item No. 188 Part No. 890254

Label Warning Guards Item 185 Part No.900327

HONDA

Honda engines have a separate choke lever that is

operated by pulling back along with moving the throttle control to the full start position if necessary. See STARTING section, see page 5.

Pull to choke

ENGINE LABELS

Briggs & Stratton

Read Owner’s Manual Before Operating. Lire le manuel d’utilisation avant la mise en route. Vor Inbetriebnahme Bedienungs - und Wartungsanleitung lesen. Favor leer las instrucciones de operacion antes de operar el motor. Consultare il Manuale Uso e Manutenzione prima dell utilizzo.

Las Skotselinstruktionen Innan Start.

Label Danger Flying Material Item 184

Label Danger Keep Hands and Feet Away Item 180 PartNo.400424

Label Shift BC2400 Item No. 186 Part No. 500202

Label Chock Wheels Item No. 189 Part No. 500168

Part No.810736

Label Clutch Blade Item 192 Part No.500177

Label Read Owner's Manual Item No. 187 Part No. 890301

Label Clutch Drive Item 191 Part No.500176

Label Patent No Item 190 Part No.500279

Honda

Part No. 500264 Form No. F101001A

Page 4 of 12

+ 9 hidden pages