Honda Automobiles Automobile Accessories User Manual

INSTALLATION

www.collegehillshonda.com/parts

INSTRUCTIONS

Accessory Application Publications No.

SECURITY SYSTEM

2001 ACCORD

2- AND 4-DOOR

(INCLUDES V6)

All 21624

Issue Date

AUG 2000

PARTS LIST

Security System (sold separately): P/N 08E51-S84-100

2 Remote controls

Control unit

LED

Push nut

2-Pin connector (for LED)

Security System Attachment (sold separately): P/N 08E55-S84-100

Security system wire harness

Sub-harness

White connector clip

Control unit bracket

Disarm switch

Window decal

3-Pin connector (for disarm switch)

Nut, 12 mm

Washer

Owner’s Manual

2 Washer-screws, 4 x 30 mm

2 Relay brackets

5 Short wire ties

3 Washer bolts, 6 x 12 mm

Ground bolt

3 Flange nuts, 6 mm

3 Self-tapping screws

Y0581-A

08E55-S84-1000-91

Wire tie with clip

9 Long wire ties

Cushion tape

Red connector clip

Relay, 4-pin

TOOLS AND SUPPLIES REQUIRED

Small flat-tip screwdriver #2 Phillips screwdriver Eye protection (face shield, safety goggles, etc.) Center punch Drill

5.5 mm, 10 mm, and 12 mm Drill bits Tape measure File Felt-tip pen Pliers 17 mm Combination wrench 10 mm Socket Ratchet Scissors Utility knife

Illustration of the Security System Installed on the Vehicle

RIGHT FUSE BOX

4-PIN RELAY

5-PIN RELAY

LED

LEFT FUSE BOX

Relay, 5-pin

Fuse label

Cover

SECURITY SYSTEM WIRE HARNESS

DISARM SWITCH

CONTROL UNIT

Adjusting the Control Unit

INSTALLATION

• Use a small flat-tip screwdriver to change the mode switch and the horn/siren switch and to adjust sensitivity.

GLASS BREAKAGE SENSOR

MAX

MIN

SENSITIVITY ADJUSTMENT KNOB

MODE SWITCH

AUT O LOCK

AUTO

MANUAL

SIREN

HORN

HORN/SIREN SWITCH

Customer Information: The information in this

installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your car. These procedures should not be attempted by "do-it-yourselfers."

1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons.

2. Disconnect the negative cable from the battery.

3. Inside the passenger’s compar tment, remove the front console lower cover (four retaining clips).

Mode Switch:

• Set the mode switch according to the customer’s choice.

• Refer to the Owner’s Manual for the explanation of each mode.

Horn/Siren Switch:

• Set the switch to “HORN” in normal use. If an optional siren is installed, set the switch to “SIREN.”

Glass Breakage Sensor:

• Do not attach anything like scotch tape over the holes; this is the microphone pickup.

Sensitivity Adjustment Knob:

• Adjust the sensitivity only if the customer requests it; the sensitivity adjustment of the glass breakage sensor is factory set.

• Be careful when you adjust the sensitivity; if you raise the sensitivity too much, the security system can give a false alarm, and if the sensitivity is too low, the security system may not work even if glass is broken.

FRONT CONSOLE LOWER CO VER

CLIP

If the vehicle you’re working on is equipped with an optional ashtray with cigarette lighter, continue with step 4, if not go to step 5.

4. Remove the ashtray with cigarette lighter, (two self-tapping screws, one connector, and four retaining clips).

ASHTRA Y WITH CIGARETTE LIGHTER

CONNECTOR

SELF-TAPPING SCREWS

CLIP

5. Remove the left fuse box cover (three retaining clips and two tabs).

TAB

CLIP

7. Remove the driver’s door sill molding (four clips).

CLIP

DRIVER'S DOOR SILL MOLDING

LEFT FUSE BOX CO VER

TAB

RET AINING CLIPS

LEFT FUSE BOX

6. Remove the driver's dashboard lower cover (three screws, and five retaining clips).

SCREW

CLIP

8. Remove the kick panel (two clips, and pull).

KICK P ANEL

SCREW

DRIVER'S DASHBO ARD LOWER CO VER

CLIP

SCREW

CLIP

+ 8 hidden pages