Honda Automobiles 08E92-SNA-100B User Manual

Download

Page 1

INSTALLATION

www.collegehillshonda.com

INSTRUCTIONS

Accessory Application Publications No.

REMOTE ENGINE

STARTER SYSTEM

2006-2008 CIVIC 4-DOOR

(A/T ONLY)

AII 38216-38957

Issue Date

FEB 2008

PARTS LIST

Remote Engine Starter Unit Kit P/N 08E91-E22-100B

Transmitter

Control unit

Antenna

Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B

Engine starter harness

Control unit bracket

Relay bracket

Key ring

Protective tape

Engine starter label

Fuse label

Accessory User’s Information Manual

Quick Start Guide

3 Black relays (4-pin)

18 Wire ties

Page 2

7 Foam cushion tapes

www.collegehillshonda.com

Flange nut

Clip

Green relay (5-pin)

Template

Illustration of the Engine Starter System Installed on the Vehicle

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Long blade flat-tip screwdriver

Small flat-tip screwdriver

6 mm Hex wrench

T25 Torx bit

3 mm and 7 mm Drill bits

File

Ratchet

10 mm Socket

Combination wrench

Isopropyl alcohol

Shop towel

Tape measure

Clip remover

Diagonal cutters

Felt-tip pen

Center punch

Scissors

2 Pairs of needle nose pliers

Rubber mallet

HDS (Honda Diagnostic System)

Masking tape

Safety goggles

INSTALLATION

RELAY (5-PIN)

2 FUSES 40A

3 RELAYS (4-PIN)

ENGINE STARTER HARNESS

2 FUSES 3A

ANTENNA

CONTROL UNIT

Customer Information: The information in this

installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

NOTE: The antenna should only be installed if the ambient air temperature 15°C (60°F) or above.

1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

7401010T

Page 3

Setting the Control Unit

CONTROL UNIT

SMALL FLAT-TIP SCREWDRIVER

Discharge any static electricity.

The switches must be selected before the control unit is plugged in.

SET

SWITCHES

SW:1 RR Junction unit -----------------------> OFF

SW:2 Trunk or Tailgate ----------------------> OFF

SW:3 Smart Entry -----------------------------> OFF

SW:4 Horn or Buzzer Answerback ------> OFF

SW:5 Trunk Main SW -------------------------> OFF

SW:6 Reserve ----------------------------------> OFF

SWITCHES

www.collegehillshonda.com

3. Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the control unit to the locations shown. Using a isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.

NOTE:

• The switches must be selected before the

control unit is plugged in.

• If the switch setting is not correct, the engine

starter will not operate correctly.

• If setting the switches when the control unit is

installed in the vehicle, touch a metal part of the screwdriver to a metal part of the vehicle to discharge any static electricity.

• If you change the switch settings with the unit

connected, you must disconnect the unit, then reconnect it before the settings will change.

SW : 1 RR Junction Unit SW : 2 Trunk or Tailgate SW : 3 Smart Entry SW : 4 Horn or Buzzer Answer Back SW : 5 Trunk Main SW SW : 6 Reserve

Removing the vehicle parts

4. Remove the trunk lid/fuel fill door opener cover (six retaining tabs). Remove one self-tapping screw.

KEY

SELFTAPPING SCREW

Unlock.

COVER

6 RETAINING TABS

TRUNK LID/ FUEL FILL DOOR OPENER

5202191T

Page 4

4. Using the key, unlock the opener.

www.collegehillshonda.com

5. Remove the left front door sill trim (two retaining tabs, five clips, and three hooks).

3 HOOKS

5 CLIPS

2 RETAINING TABS

7. If equipped, remove the driver’s dashboard under cover (turn the knob counterclockwise, and release two clips and pin).

FRONT

LEFT FRONT DOOR SILL TRIM

5202200T

6. Pull away the weatherstrip, and remove the left kick panel (two clips).

WEATHERSTRIP

2 CLIPS

DRIVER’S DASHBOARD UNDER COVER

KNOB

5202112T

8. Remove the driver’s dashboard lower cover (eight clips).

DRIVER’S DASHBOARD LOWER COVER

8 CLIPS

5202121T

LEFT KICK PANEL

5202220T

Page 5

9. Lower the tilt lever, and pull the steering wheel

www.collegehillshonda.com

toward you. Insert a long blade flat-tip screwdriver along the guide of the column lower cover, and pry the retaining tab of the column upper cover.

2 RETAINING TABS

11. Remove the column lower cover (two self-tapping screws and one screw).

COLUMN UPPER COVER

2 HOOKS

RETAINING TAB

Push.

TILT LEVER

GUIDE

LONG BLADE FLAT-TIP SCREWDRIVER

COLUMN LOWER COVER

6608050T

SCREW

COLUMN LOWER COVER

2 SELF-TAPPING SCREWS

5308530T

10. Push on the column lower cover in the area shown to separate the column upper cover from the column lower cover (two retaining tabs). Pull up to remove the column upper cover (two hooks).

Page 6

12. If equipped, use a small flat-tip screwdriver to

www.collegehillshonda.com

remove the left and right lens from the map light console (four retaining tabs for each lens). Remove the two bolts, and then release the map light console.

FRONT

MAP LIGHT CONSOLE

14. Remove the cap from the left sunvisor (four retaining tabs).

CONNECTOR

4 RETAINING TABS

BOLTS

LENS

6D01390T

13. Remove the sunvisor holders. Using a small flattip screwdriver, push the hook, and turn the holder 90°, then pull it out.

MAP LIGHT CONSOLE

CAP

TORX SCREW

LEFT SUNVISOR

5217030T

15. Remove the left sunvisor (two T25 Torx screws, and unplug the vehicle connectors).

16. Pull away the weatherstrip from the left front pillar trim.

Strike perpendicularly to the vehicle.

FRONT PILLAR

FRONT PILLAR TRIM

CLIP

SHOP TOWEL

SUNVISOR HOLDER

SMALL FLAT-TIP SCREWDRIVER

6D01400T

WEATHERSTRIP

CLIP

LEFT FRONT PILLAR TRIM

STRIKE POINT

17. Using a rubber mallet and a shop towel, gently tap the left front pillar trim at the position shown to release the clip. Gently tap the pillar trim just below the “SIDE CURTAIN AIRBAG” mark.

RUBBER MALLET

5006010T

Page 7

18. Pull away the weatherstrip from the left front pillar

6D01210T

www.collegehillshonda.com

trim. Remove the left front pillar trim (two clips).

Installing the Antenna

20. Using scissors, cut out the template.

LEFT FRONT PILLAR TRIM

WEATHERSTRIP

2 CLIPS

5202100T

19. Remove the clip from the left front pillar trim, and install a new clip on the left front pillar trim.

NEW CLIP

SCISSORS

Cut out.

TEMPLATE

6D01203T

21. Secure the template to the windshield with the tape by aligning it with the edge of the black ceramic paint as shown.

LEFT FRONT PILLAR TRIM

CLIP (Discard.)

5217110T

BLACK CERAMIC PAINT

WINDSHIELD TEMPLATE

TAPE

EDGE OF BLACK CERAMIC PAINT

Align the end with the end of the black ceramic paint.

Page 8

22. Using two pairs of needle-nose pliers, bend the

www.collegehillshonda.com

antenna plate according to the illustration and measurement shown.

23. Measure the antenna cable as shown. Attach the three foam cushion tapes to the antenna cable in the measurement shown.

ANTENNA

SCALE

15 mm (0.6 in.)

8 mm (0.3 in.)

ANTENNA CABLE

FOAM CUSHION TAPE

30 mm (1.2 in.)

ANTENNA

360 mm (14 in.)

30 mm (1.2 in.)

6D01240T

24. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. Allow the area to dry before proceeding.

ROOF LINER Clean with

isopropyl alcohol.

PLATE

NEEDLE-NOSE PLIERS

6D01222T

TEMPLATE

ADHESIVE BACKING

PLATE

ANTENNA

6D01250T

25. Remove the adhesive backing from the antenna, insert the antenna plate under the roof liner, and attach the antenna to the windshield aligning the template.

26. Remove the template.

Page 9

27. Route the antenna cable under the roof liner

6D01270T

6D01410T

www.collegehillshonda.com

towards the driver’s side of vehicle, and down along the vehicle harness. Be careful not to crease the roof liner.

ROOF LINER

29. Using isopropyl alcohol on a shop towel, clean the areas where the foam cushion tape will attach. Under the roof liner, secure the antenna cable to the roof panel with the two foam cushion tapes (cut one foam cushion tape in half) in the areas shown.

VEHICLE HARNESS

ANTENNA CABLE

6D01260T

28. Continue routing the antenna cable between the front pillar and the dashboard.

FRONT PILLAR

ROOF LINER

ANTENNA CABLE

FOAM CUSHION TAPE

FOAM CUSHION TAPE (1/2)

30. Secure the antenna cable to the vehicle harness with four wire ties as shown. Do not secure the antenna cable to the drain tube.

4 WIRE TIES

VEHICLE CLIP

DRAIN TUBE

DASHBOARD

ANTENNA CABLE

5308192T

VEHICLE HARNESS

ANTENNA CABLE

Page 10

31. Secure the antenna cable to the vehicle harness

www.collegehillshonda.com

with a wire tie. Secure the wire tie between the vehicle harness branching points.

VEHICLE HARNESS

WIRE TIE

Routing the Engine Starter Harness

33. Attach the 3 A fuse labels to the engine starter harness fuse case, and the 40 A fuse labels to the fuse block.

LAYOUT OF RELAYS WHEN VIEWED FROM FRONT

4-PIN RELAY (black)

ANTENNA CABLE

BRANCHING POINTS

6D01281T

Installing the Control Unit Bracket

32. Locate the small square hole next to the small round hole in the dashboard support bracket. Under the dash, attach the control unit bracket to the vehicle bracket near the front lower pillar using a flange nut. If the vehicle is equipped with a moonroof, be careful not to pull on the drain tube.

VEHICLE BRACKET

FRONT

5-PIN RELAY (green)

CLIP

FUSE BLOCK

4-PIN RELAY (black)

RELAY BLOCK

40 A FUSE LABEL

FUSE CASE

3 A FUSE LABEL

6D01031T

34. Install the four relays to the engine starter harness relay blocks. Be careful to install the relays properly, or a malfunction will result.

VEHICLE BRACKET

CONTROL UNIT BRACKET

FLANGE NUT

6D01123T

Page 11

6D01071T

35. Route the engine starter harness 7-pin connectors

www.collegehillshonda.com

up the steering column and to the ignition switch. Unplug the white vehicle 7-pin connector. Plug the white engine starter harness 7-pin connectors into the white vehicle 7-pin connectors.

IGNITION SWITCH

VEHICLE 7-PIN CONNECTOR (white)

ENGINE STARTER HARNESS 7-PIN CONNECTOR (white)

37. Disconnect the vehicle 8-pin connector on the rear of the wiper switch and plug the engine starter harness 8-pin connector into the vehicle 8-pin connector.

ENGINE STARTER

VEHICLE 8-PIN CONNECTOR

HARNESS 8-PIN CONNECTOR

6D01081T

36. Unplug the brown vehicle 7-pin connector, and plug the brown engine starter harness 7-pin connector into the brown vehicle 7-pin connector.

NOTICE Make sure that the engine starter harness 7-pin connector is connected to the vehicle connector and it is locked securely. A loosely connected connector can cause engine stall during driving.

ENGINE STARTER HARNESS 7-PIN CONNECTOR (brown)

WIPER SWITCH

6D01101T

38. Secure the connected 8-pin connector with a wire tie to the engine starter harness.

CONNECTED 8-PIN CONNECTOR

WIRE TIE

ENGINE STARTER HARNESS

Pull the connector and check that it is locked securely.

VEHICLE 7-PIN CONNECTOR (brown) (Not reconnected.)

6D01091T

WIPER SWITCH

Page 12

39. Wrap the vehicle 7-pin connector with one foam

www.collegehillshonda.com

cushion tape, then place the vehicle 7-pin connector into the gap of the column.

VEHICLE 7-PIN CONNECTOR (brown) (Squeeze into

this area.)

ENGINE STARTER HARNESS

GREEN TAPE

4 WIRE TIES

42. At the right of the steering shaft, locate the sub joint box. Using a small flat-tip screwdriver, unplug the vehicle 6-pin connector from the sub joint box. Plug the engine starter harness 6-pin connectors into the vehicle 6-pin connector and the subjoint box.

VIEWED FROM UNDERSIDE

VEHICLE 6-PIN CONNECTOR

SUB JOINT BOX

FOAM CUSHION TAPE

VEHICLE 7-PIN CONNECTOR

VEHICLE BRACKET

VEHICLE HARNESS

LOCK

VEHICLE HARNESS

WIRE TIE

ENGINE STARTER HARNESS

6D01111T

40. Secure the engine starter harness to the vehicle harness with four wire ties in the areas shown. The lock of the wire ties should face up.

41. Remove the lower steering column support bracket bolt. Attach the relay bracket to the steering column support bracket and reinstall the steering column support bracket bolt.

FRONT

ENGINE STARTER HARNESS 6-PIN CONNECTOR

VEHICLE 6-PIN CONNECTOR

6D01162T

43. Attach the relay blocks and fuse case on the relay bracket.

VEHICLE HARNESS

WIRE TIE

RELAY BRACKET

FUSE STEERING COLUMN SUPPORT BRACKET BOLT (Reuse.)

RELAY BRACKET

STEERING COLUMN SUPPORT BRACKET

6D01063T

44. Secure the engine starter harness to the vehicle harness using a wire tie.

CASE

RELAY BLOCK

ENGINE STARTER HARNESS

6D01302T

Page 13

45. With driver's dashboard under cover: Measure

6D01172T

www.collegehillshonda.com

the indicated dimension on the instrument panel and mark with a felt-tip pen and a center punch.

INSTRUMENT PANEL

View from below

46. Secure the engine starter harness to the vehicle harness using a wire tie.

• With driver's dashboard under cover: Secure

in the hole you made in the instrument panel.

• Without driver's dashboard under cover:

Secure through the existing hole for under cover securing.

WIRE TIE

FRONT

6 mm (0.2 in.)

12 mm (0.5 in.)

FELT-TIP PEN

CENTER PUNCH

6D01351T

Drill a 3 mm hole and then a 7 mm hole at the

marked position of the instrument panel.

– Wear safety goggles during drilling.

– Using a file, remove the burrs at the edges

of the holes you made.

INSTRUMENT PANEL

WITH DRIVER’S

FUSE BOX

CLIP

DASHBOARD UNDER COVER

47. Use the clip on the engine starter harness to secure the engine starter harness to the fuse box.

DRILL BIT (3 mm, 7 mm)

DRILL

6D01361T

Page 14

48. Disconnect the vehicle 42-pin, 4-pin and 2-pin

www.collegehillshonda.com

connectors.

FUSE BOX

VEHICLE 4-PIN CONNECTOR

VEHICLE 42-PIN CONNECTOR

FUSE BOX

VEHICLE 2-PIN CONNECTOR

FRONT VIEW

VEHICLE 2-PIN CONNECTOR

VEHICLE 4-PIN CONNECTOR

49. Plug the engine starter harness 4-pin and 2-pin connectors into the fuse box.

NOTICE Check that the engine starter harness 4-pin and 2-pin connectors are connected to the fuse box and they are locked securely. Loosely connected connectors can cause engine stall during driving.

4-PIN CONNECTOR PORT

2-PIN CONNECTOR PORT

FOAM CUSHION TAPE

VEHICLE HARNESS

VEHICLE 42-PIN CONNECTOR

LOCK

6D01430T

WIRE TIE

VEHICLE 2-PIN CONNECTOR

VEHICLE 4-PIN CONNECTOR

ENGINE STARTER HARNESS 4-PIN CONNECTOR

ENGINE STARTER HARNESS 2-PIN CONNECTOR

Pull the connector and check that it is locked securely.

FUSE BOX

6D01292T

50. Wrap foam cushion tape to the vehicle 2-pin and 4-pin connectors and secure them with a wire tie. Then, secure the vehicle harness with a wire tie. Reconnect the vehicle 42-pin connector.

Page 15

6D01181T

51. Connect the engine starter harness 18-pin

www.collegehillshonda.com

connectors with each other and secure them with a wire tie to the vehicle harness.

ENGINE STARTER HARNESS 18-PIN CONNECTORS

WIRE TIE

VEHICLE HARNESS

6D01331T

52. Unplug the white vehicle 14-pin connector at the front lower pillar behind the fuse box, and plug the engine starter harness 14-pin connectors in between. Attach the engine starter harness 14pin connector to the vehicle 14-pin connector.

53. Install the clip from the engine starter harness to the fuse box bracket behind the fuse box.

GROUND BOLT (Reuse.)

FRONT

ENGINE STARTER HARNESS GROUND TERMINAL

CLIP

FUSE BOX BRACKET

ENGINE STARTER HARNESS

54. Remove the ground bolt from the vehicle. Secure the engine starter harness ground terminal with the ground bolt you just removed.

FUSE BOX

VEHICLE WHITE 14-PIN CONNECTOR

ENGINE STARTER HARNESS 14-PIN CONNECTOR

6D01141T

Page 16

Installing the Control Unit

www.collegehillshonda.com

55. Connect the antenna cable terminal and the engine starter harness 18-pin connector to the control unit.

ANTENNA CABLE TERMINAL (Connect first.)

CONTROL UNIT

CONTROL UNIT BRACKET

ENGINE STARTER HARNESS 18-PIN CONNECTOR

6D01312T

FRONT

58. Using isopropyl alcohol on a shop towel, clean the area where the engine starter label will attach.

HOOD

ADHESIVE BACKING

ENGINE STARTER LABEL

6D01421T

59. Attach the engine starter label to the back of the hood.

60. Check that all wire harnesses are routed properly and all connectors are plugged in.

56. Install the control unit on the control unit bracket.

57. Bundle the excess antenna cable with two wire ties and secure it with one wire tie to the vehicle harness.

ANTENNA CABLE

WIRE TIES

VEHICLE HARNESS

61. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the airbag with a clip during reinstallation of the front pillar trim. Do not push the front pillar trim excessively.

62. Reconnect the negative cable to the battery. Check that the electrical accessory and other electrical systems function properly.

63. Perform REMOTE ENGINE STARTER

REGISTRATION, on pages 18-20, and FUNCTION CHECK, on page 21.

64. Enter the customer’s radio anti-theft code, and reset the radio station presets.

65. Reset the clock.

7401020T

Page 17

752504AS

752503AS

REMOTE ENGINE STARTER REGISTRATION

www.collegehillshonda.com

1. Acquire the PCM code from ISIS.

2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the ON (II) position.

3. Start the HDS, and click the car icon.

CAR ICON

5. Select Honda Systems, then click the check button.

752501AS

4. Input the VIN and other required information into the HDS, then click the check button.

Select “Honda Systems.”

CHECK BUTTON

6. Select R/C ENG STARTER and click the check button.

Select “R/C ENG STARTER.”

CHECK BUTTON

other required information.

CHECK BUTTONInput the VIN and

752502AS

Page 18

7. A REMARKS message will display. Click the

www.collegehillshonda.com

check button.

“REMARKS” message

CHECK BUTTON

9. The following message will display: Obtain PCMcode (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA). Click the check button.

“Obtain PCM-code" message

752505AS

CHECK BUTTON

8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button.

Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”

CHECK BUTTON

752506AS

752507AS

10. Input the PCM Code, then click the check button.

NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.

Input the PCM code.

CHECK BUTTON

752509AS

Page 19

11. The following message will display: The

www.collegehillshonda.com

registration of the Remote Control Engine Starter Unit has been completed. Click the

check button.

"Registration" message

CHECK BUTTON

752510AS

12. The following message will display: Check that

the engine can be started by the Transmitter.

Click the check button.

“Check that the engine can be started by the Transmitter”

CHECK BUTTON

752511AS

13. Perform the function check on page 21, then disconnect the HDS.

Page 20

FUNCTION CHECK

www.collegehillshonda.com

Operating Conditions

• The hood is closed.

• Shift lever is in Park.

• The key is not in the ignition switch.

• All doors and trunk are closed and locked.

Inspection

1. Within 1 second, press the command button and then the start button on the transmitter. The engine should start if all operating conditions are met.

Does the engine start?

Yes - Operation is normal. No:

• Make sure all operating conditions are met.

• Check the engine starter harness connections.

• Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.)

2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop.

Does the engine stop?

Yes - Operation is normal. No - Check the engine starter harness connections.

3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:

NOTE:

After each test the ignition key must be cycled, or the driver’s door must be opened and closed.

– Move the shift lever out of the P position.

– Unlock or open the doors or the trunk lid.

– Open the hood.

– Insert the key in the ignition switch.

– Press on the brake pedal.

Does the engine stop after each of these tests? Yes - Operation is normal. No - Check the engine starter harness connections.

DISPLAY

STOP BUTTON

COMMAND BUTTON

START BUTTON

TRANSMITTER

732904AY

4. Check that the power windows or the moonroof does not function when the engine is started with the transmitter.

5. Press the command button on the transmitter twice and check the vehicle condition on the display.

6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and when the vehicle is in direct sight.