Honda Automobiles 08E55-SHJ-100, 08E51-SHJ-100, 08E55-SHJ-1000-81 User Manual

Download

Page 1

Kit No. 08E51-SHJ-100

08E55-SHJ-100

Security System Owner’s Manual

ODYSSEY

Page 2

Contents

Introduction Emergency Disarming

During the Panic Alarm Activation ............ 4

During the Entry Delay Time ..................... 4

System Controls

Arming Mode (MANUAL Arming Mode (AUTOMATIC

Valet

Placing the System in the Valet Mode ...... 7

In the Valet Mode ...................................... 8

Exit From the Valet Mode .......................... 9

..................................................... 3

AUTOMATIC). 5

MANUAL) ..

Arming

Arming Methods ...................................... 10

Manual Arming (Remote Controlled) ...... 10

Automatic Arming (Passive) .................... 11

Alarm Mode

Alarm Triggered Mode ............................. 13

Disarming

Remote Control Disarming ..................... 14

Tripped Sensor Warning and Indication

Tripped Sensor Warning.......................... 15

Tripped Sensor Indication ....................... 16

Glossary ........................................................ 17

Specifications................................................ 19

Please write the serial number of the remote control and the main unit belo Keep this booklet as a record of your purchase.

Remote Control No.:

Main Unit No.:

Page 3

Introduction

Congratulations on your purchase of this Honda Security System. Your Honda Security System is the product of years of research and development. It will give you many years of reliable perf protection, and convenience.

The system consists of two major components: a main unit and a remote control transmitter.

The main unit is the brain of the system. The built-in prog microprocessor monitors your vehicle for optimal protection. Security System also offers various options to tailor the system to the preferences of different users.

The remote control allows you to turn the system on and off from outside the vehicle while simultaneously locking and unloc doors*. The transmitter can also be used to intentionally activ horn in case of an emergency.

To take full advantage of your Honda Security System, w you to read this manual thoroughly.

The Security System can be operated with the vehicle’ For operation of the Keyless Entry System, refer to the v

ormance,

rammable

The

king the

ate the

e encourage

s Keyless Entry System.

ehicle Owner’s Manual.

Due to the expertise required to properly install the Honda Secur System, we highly recommend that the installation be perf your Honda dealer. Proper wiring and component placement are essential for optimum system performance.

ormed by

ity

Page 4

Emergency Disarming

During the Panic

• The system can be disarmed using the ignition ke

Alarm Activation

• This method of disarming also serves as an emergency o

LOCK

During the Entry Delay Time

Status LED

LOCK

the system.

transmitter cannot be used.

Enter the vehicle and insert the ignition key.

Turn the ignition key to the ON (II) position. The system stops the panic alarming when the ignition k Check to see the status LED goes off.

4625011B

• When the system is being armed by the AUTOMATIC ar 20-seconds entry delay time after opening a door or the tailgate

• If the system is armed by the remote control transmitter seconds, and the alarm is triggered immediately when a door is opened.

To disarm the entry delay time mode, insert the ignition k

Turn the ignition key to the ON (II) position. The security system disar turned to the ON (II) position. Check to see the status LED goes off.

y regardless of the method used to arm

verride if the remote control

ey is turned to the ON (II) position.

ming method, there is a

, the entry delay time is set to 0

ey after opening a door or the tailgate.

ms when the ignition key is

Page 5

System Controls

Arming Mode (MANUAL

AUTOMATIC)

within 5 seconds

4625020B

This section explains how to change the arming mode from MANU

The arming mode of the Security System is preset to MANU

NOTE:

NOTE: Steps 1 thru 5 must be completed within 5 seconds.

Insert the ignition key.

Remove the ignition key from the ignition switch. (All the w

Insert the ignition key.

Remove the ignition key from the ignition switch. (All the w

Insert the ignition key. Observe that the system beeps once.

MANUAL MODE

AUTOMATIC MODE

ay out)

The switching procedure is

Not completed No beep

Completed

AL to AUTOMATIC.

AL arming.

The result

Beep once

Page 6

System Controls

Arming Mode (AUTOMATIC

4625030B

4 5

6 7

LOCK

MANUAL)

Status LED

4625051B

within 5 seconds

4625020B

This section explains how to change the arming mode from A

Turn the ignition key from the ON (II) position to the LOCK (0) position. Remove the key from the ignition switch.

Open a door or the tailgate and close it. (The EXIT dela Check that the status LED blinks.

NOTE: Steps 3 thru 7 must be completed within 5 seconds.

Insert the ignition key.

Remove the ignition key from the ignition switch. (All the w

Insert the ignition key.

Remove the ignition key from the ignition switch. (All the w

Insert the ignition key. Observe that the system beeps twice.

AUTOMATIC MODE

MANUAL MODE

The switching procedure is

UTOMATIC to MANUAL.

y starts.)

ay out)

Not completed No beep

Completed Beep twice

The result

Page 7

Valet

Placing the System in the Valet Mode (Valet Mode can be changed only from

Automatic Arming Mode)

NOTE: Steps 1 and 2 must be completed within 5 seconds.

Status LED

4625051B

4625060B

Remove the ignition key from the ignition switch.

Press the UNLOCK button on the remote control transmitter three times

within 5 seconds

The Status LED flashes once, indicating that the system is ready to change the mode

Exit the vehicle and close the door. (The system is changed to

• When the security system is placed in the valet mode, it is tempora placed on hold. When in the valet mode, the system cannot be ar but panic mode is still functional. This is a convenient f is to be washed, serviced, or valet parked.

• Before removing the ignition key, opening/closing of the door or tailgate is not related to set valet mode.

Valet mode.)

eature if the car

rily

med,

Page 8

Valet

In the Valet Mode:

4625060B

Status LED

4625051B

Status LED

4625051B

If you follow either procedure below, the Status LED blinks once to sho the system is in the Valet mode.

Open one of the doors or the tailgate. The Status LED blinks once.

After turning the ignition switch to LOCK (0), remove the ignition k The Status LED blinks once.

Keyless/Security during the Valet Mode.

Lock/Unlock of Keyless

VALET MODE is ON Active

VALET MODE is OFF Active

Panic of Keyless

Active

Arming/Disarming of

Non-Active

Active

ey.

Security

Page 9

Exit From the Valet Mode

Valet

4625051B

Status LED

With the system in the Valet mode, take the key out of the ignition s

Press the UNLOCK button on the remote control transmitter

Observe that the Status LED flashes twice, indicating that the system is out of the The system is now in the Disarm mode.

witch.

Valet mode.

Page 10

Arming

4625030B

Arming Methods

Manual Arming (Remote Controlled)

There are two possible ways to arm the system:

• MANUAL Arming (Remote Control)

• AUTOMATIC Arming (Passive)

• When the main unit is set to MANUAL, the system is ar

transmitter. This is the factory setting.

• The system beeps three times. It does not arm itself unless an closed when the LOCK button is pressed.

1 2

Make sure the arming mode is set to MANUAL.

Turn the ignition key to the LOCK (0) position. Remove the key from the ignition switch. Exit the vehicle, then close all the doors and the tailgate.

Press the LOCK button on the remote control transmitter. Observe that:

• The remote control LED illuminates.

• The security system starts to arming delay.

• The status LED flashes once per second.

• The parking lights flash once. (Be sure to

• The doors lock.

• After 15 seconds, the security system arms itself.

• The status LED flashes once per 3 seconds.

If the LOCK button is pressed a second time (within 5 seconds of the first push) the horn beeps once to confirm the doors are locked and the system is armed.

med by using the remote control

y door or the tailgate is

(Be sure to check the status LED flashes.)

check that the lights flash.)

(Be sure to check the status LED flashes.)

Page 11

Arming

Automatic Arming (Passive)

(Arms the security system without

locking the doors.)

OFF

• When the main unit is set to AUTOMATIC, the system ar the last door or the tailgate is closed

• If a door or the tailgate is opened during the 20 seconds e the 20 seconds exit delay time restarts after the last door or the tailgate is closed.

• If the ignition key is inserted into the ignition switch dur be disarmed.

• The system beeps three times. It does not arm itself unless an when the LOCK button is pressed.

• When the remote control transmitter is used to arm dur to arm by manual arming function. When the system is ar it can be armed in manual arming mode by using the remote control tr and Entry delay cannot be used.

Make sure the arming mode is set to AUTOMATIC.

Turn the ignition key from the ON (II) position to the LOCK (0) position. Remove the key from the ignition switch.

The ignition key must be removed from the ignition switch bef

ms automatically 20 seconds after

xit delay time, the timer resets and

ing the exit delay time, the system will

y door or the tailgate is closed

ing exit delay time, the system starts

med in the automatic arming mode,

ore the system will arm.

ansmitter. Exit delay

Page 12

Arming

4628020B

4625030B

20-sec exit delay time

Exit the vehicle, and close all the doors and the tailgate

The system arms automatically 20 seconds after the last door or the tailgate is closed. that:

• The status LED flashes four times per second during the e seconds after the system is armed. (Be sure to chec

• The parking lights flash once without a beep to confir (Be sure to check that the lights flash.) NOTE: When the LOCK button on the remote control tr delay time, the arming function of the remote control tr

xit delay time, and once per 3

k that the status LED flashes.)

m the system is armed.

ansmitter is pressed during the exit

ansmitter has priority.

Observe

Page 13

Alarm Mode

Alarm Triggered Mode

• After the system is armed, opening of any door or the tailgate will trigger the alarm.

• If the door or tailgate is kept open, the alarm will contin

• If the battery is disconnected in the alarm mode, an

send the alarm into the triggered mode.

When the alarm is triggered, observe that:

ue to sound for 5 minutes.

y attempt to reconnect the battery will

• The horn sounds once per 1.5 seconds for one alarm duration (horn duration is 30 seconds).

• The parking lights flash once per 1.5 seconds for one alarm duration (parking lights duration is 30 seconds).

• The status LED flashes twice per second for one alarm duration.

• After one alarm duration, the system automatically rearms.

The entry delay time is functional only

4628030B

NOTE:

when the arming mode is set to AUTOMATIC and the door or tailgate is open.

Press the UNLOCK button of the remote control transmitter to cancel the alarm, and the system disarms.

, or breaking of window glass

Page 14

Disarming

Remote Control Disarming

• Regardless of the method used to arm the system, the system can be disar remote control transmitter.

4628040B

Press the UNLOCK button once on the remote control transmitter. Observe that:

• The remote control LED illuminates.

• The security system disarms and the

parking lights flash twice when the alarm has not been triggered. If the alarm has been triggered, the horn sounds four times to tell you the alarm has been triggered.

• The doors and tailgate are unlocked.

After being disarmed, the system will

NOTE:

rearm in 30 seconds if a door or the tailgate is not opened.

med using the

Page 15

Tripped Sensor Warning and Indication

Tripped Sensor Warning

4625020B

• The system will warn you that the security system has been tr

If the system was tripped and automatically rearmed, obser

• The horn sounds four times when the system is disarmed.

ve that:

ipped in your absence.

Page 16

Tripped Sensor Warning and Indication

Tripped Sensor Indication

1 2

4628070B

TRIPPED SENSOR

Door or Tailgate Ignition Key Switch Ignition Switch Battery Disconnected Glass Breakage

STATUS LED

NUMBER OF FLASHES

Status LED

4625051B

• After disarming the system, if the tripped sensor wa identify which portion of the security system has been tr flashes as shown below.

• Information regarding the security system can be retr systems main control unit.

Disarm the security system. Close the door and tailgate.

Insert the ignition key.

Within 1 second after step 2, open a door or the tailgate.

Within 1 second after step 3, remove the key from the ignition s The status LED flashes to indicate which sensor(s) was/w

Example 1: If opening a door or the tailgate causes the alarm to be tr pause and repeat this sequence for 1 minute. Example 2: If the alarm is triggered twice, small number is shown first. second trigger is Door opening. The Status LED will flash once (door), pause (glass), pause and repeat this cycle of operation for 1 min

rning indicator appears, you can

ipped by observing the number of

ieved from the memory of the

witch.

ere tripped.

iggered, the Status LED will flash once,

First trigger is Glass breakage and

ute.

, flash four times

Page 17

Description

Glossary

ALARM DURATION

ARM

AUTOMATIC ARMING

MANUAL ARMING

DISARM

ENTRY DELAY TIME

EXIT DELAY TIME

Functional only in the Automatic Arming mode.

The amount of time the horn sounds when the alarm is tr activated. The duration is 30 seconds.

To turn the security system

The optional mode in which the security system is armed automatically (passiv doors and the tailgate are closed. The doors and tailgate do not loc

The mode in which the system is armed and disarmed b the factory preset mode.

To turn the security system

The amount of time before the alarm is triggered after the door or tailgate is opened, when the system is set to the automatic arming mode.

The amount of time before the system arms after all the doors and the tailgate are closed when the system is set to the automatic arming mode.

’s protection on.

’s protection off.

ipped or the panic feature is

ely) after all the

k when the system is armed.

y the remote control transmitter. This is

Page 18

Glossary

Description

EXTENDED EXIT ARMING

PANIC

SENSOR CANCELLATION

TRIPPED SENSOR INDICATION

TRIPPED SENSOR WARNING

VALET

Functional only in the Automatic Arming mode.

If a door or the tailgate is opened during the exit delay time countdown procedure when the specific door or the tailgate is closed.

A mode in which the horn and lights are intentionally activ Useful for attracting attention in case of an emergency

A feature that cancels (ignores) a particular sensor that has caused the alar tripped consecutively for 5 minutes.

A feature that indicates, through the status LED, the sensor that tr diagnostic feature that recalls the tripped sensor from memor the alarm is rearmed.

A feature that tells the owner that the alarm was tripped in his or her absence

A mode in which the system cannot auto-arm. This is useful when the car is being ser parked, or washed. The remote control transmitter will not ar mode. The panic feature will continue to work in the valet mode

, the timer will reset and restart the

ated.

m to be

ipped or activated the alarm. A

y. This feature is not disabled once

m or disarm the system in the valet

viced, valet

Page 19

Specifications

Main Unit

Design ...................................................................................................

Operating Voltage ...............................................................................

Current Consumption (Arming) ...................................................................................................

Operating Temperature ...............................................................................................

Dimensions .................................................................................................

Net Weight .....................................................................................................................

Due to continuous product improvement, specifications and

NOTE:

design are subject to change without notice.

Microprocessor, all solid state

13 V DC (8 V to 16 V

81 mm

(3-3/16"

× 2-15/16" ×

allowable)

–40°F to +185°

(–40°C to + 85°

× 75 mm

× 34 mm

1-11/32")

............

.2 mA

0.08 kg

(2.8 oz)

Page 20

08E55-SHJ-1000-81

ved.

Printed in Japan