Navigation General Commands...132
Navigation Display Commands...133
Find Place Commands.................134
Climate Control Commands ........135
Temperature Voice Commands ...136
Radio Voice Commands..............136
CD Voice Commands..................137
DVD Voice Commands...............137
AUX Voice Commands...............138
Rear Radio Voice Commands .....138
Rear CD Voice Commands .........139
Rear DVD Voice Commands ......139
Rear AUX Voice Commands ......140
Information Screen Voice
Commands................................140
Setup Screen (first) Commands...140
On-Screen Commands.................141
On-Screen Commands Assist.........141
Index ......................................... 143
Navigation System3
Introduction
2008 Odyssey 00X31-SHJ-8101
Main Menu
Manual Overview
The manual is divided into the
following sections:
• Getting started - A basic introduction
that discusses the controls and how to
communicate with the system.
• Entering a Destination - How to enter
an address or locate a point of interest
(POI).
• Driving to your Destination – An
explanation of the map features,
guidance, and cautions.
• Information Features - Cellular
Phonebook*, Voice Command Help,
Map Legend, Calendar, Calculator,
and Key to Zagat Ratings.
* Available only for the Touring
model.
• System Set-up - How to set up and
tailor the system for your personal
use and use the Address Book.
The back of this manual contains:
• Map Coverage (page 110)
• Frequently Asked Questions (FAQs)
(page 121)
• Troubleshooting Guide (page 128)
• Glossary of Terms (page 129)
• Voice Command List (page 132)
System Overview
Your navigation system is a highly
sophisticated location system with voice
control that uses satellites and a map
database to show you where you are and
to help guide you to a desired
destination.
The navigation system receives signals
from the global positioning system
(GPS), a network of 24 satellites in orbit
around the earth. By receiving signals
from several of these satellites, the
navigation system can determine the
latitude, longitude, and elevation of
your vehicle. In addition, a gyroscopic
yaw sensor and a vehicle speed sensor
in your vehicle keep track of the
direction and speed of travel at all times.
The navigation system applies this
location, direction, and speed
information to the maps and calculates a
route to the destination you enter. As
you drive to that destination, the system
provides map and voice guidance.
4Navigation System
Introduction
2008 Odyssey 00X31-SHJ-8101
Main Menu
The navigation system is easy to use.
The locations of many places of
business and entertainment are already
entered in the system. You can select
any of them as a destination by using the
touch screen, joystick or voice control.
There are several ways to enter a
destination, such as by point of interest
(POI), by address, by phone number,
and by selecting it from the map. The
last 50 destinations are saved for reuse
at a later date. The system also allows
you to store a home address to simplify
returning home from your destination.
Accessories Precautions
If you have front window tinting
installed, be aware that if the tint has
metallic properties, it can seriously
degrade or prevent GPS reception. This
is because the GPS antenna is located
under the dashboard.
If you plan to install electronic
components such as radar detectors,
vehicle location devices, remote
starters, additional amplifiers, or other
audio components, ensure that they are
not located near the navigation control
unit under the driver’s seat, near the
navigation screen in the dash, or near
the GPS antenna under the dashboard.
Signal noise emanating from these
devices can cause intermittent
disruption of the navigation system.
Important Safety Information
The navigation system can distract your
attention from the road if you focus on
the screen or operate the system’s
controls while driving.
Enter as much information as possible
into the system before you begin
driving, or when the vehicle is stopped.
Then, as you drive, listen to the audio
instructions and use voice commands
when possible.
Navigation System5
Introduction
2008 Odyssey 00X31-SHJ-8101
Main Menu
WARNING
Using the navigation system
while driving can take your
attention away from the road,
causing a crash in which you
could be seriously injured or
killed.
Follow all operating instructions
and safety information in this
manual.
While driving, do not look at the screen
or operate the system controls for more
than a second or so at a time, and only
after deciding you can do so safely. Pull
to the side of the road if you need more
time to look at the screen or operate the
controls.
The navigation system is designed to
provide route information to help you
reach your destination. However, this
route guidance may sometimes conflict
with current road conditions such as
street closures, road construction,
detours, and out-of-date map data.
Additionally, the system itself has
certain limitations (see page 103).
Therefore, you must verify the audio
and visual route information provided
by the system by carefully observing the
roadway, signs and signals, etc. If you
are unsure, proceed with caution.
Always use your own good judgment,
and obey traffic laws while driving.
Map Overview
Current Street
The current street on which your vehicle
is, appears at the bottom of the map
screen (see page 20). A message saying
“Not on a digitized road” may appear
instead when you drive half a mile away
from a mapped road. For more details,
see Off-road Tracking on page 62.
Verified/Unverified Street
Your navigation system has two kinds
of streets: verified (dark colored) and
unverified (light colored). The
differences between the two types of
streets are contrasted in the chart on
page 7.
These roads are found within metropolitan areas, and
include interstate freeways and major roads
connecting cities.
Shown on daytime map screen as black or red, such as
interstate freeways.
The database vendor has verified these streets.
Information like turn restrictions, average speed, and
whether it is a one way street have been gathered and
used when creating your route to a destination.
While driving to your destination, the displayed route
line is solid blue. The system provides voice and map
guidance to your destination.
There are no pop-up boxes urging extra caution during
a route. However, because roads constantly change,
you are urged to use common sense, and always obey
posted traffic restrictions.
Voice guidance issues maneuvers such as “In a half
mile make a right turn.”
The time and distance “to go,” displayed while on
route to a destination, is based on the average speed
and distance for the roads used for your route.
Introduction
These roads are found in rural areas, and typically include
residential streets away from the center of a town.
Shown on the daytime map screen as light brown.
These streets have not been verified by the database vendor. The
system does not contain information on one-way streets, turn
restrictions, or the road’s average speed. They are shown on the
map for reference and can have errors in map location, naming,
and address range.
Your route line is either a blue dotted “vector line,” or a dashed
pink/blue line. For information on selecting this option, and the
routing differences, see Unverified Area Routing on page 87.
Regardless of whether the user chooses route guidance, there are
cautionary screens before and during the route urging the user to
be extra cautious, and obey all traffic restrictions. See Unverified Area Routing on page 87.
The suffix “if possible” is added to each guidance maneuver. For
example: “In a half mile make a right turn, if possible.”
Because the average speed of these roads is not known, the time
and distance “to go” is based on a fixed average speed of 25 mph
for these roads.
Navigation System7
User Agreement
2008 Odyssey 00X31-SHJ-8101
Main Menu
In using this DVD “Satellite Linked
Navigation System” (the “DVD”),
which includes HONDA MOTOR CO.,
LTD. software, ALPINE
ELECTRONICS, INC. software,
NAVTEQ database contents, INFO
USA CORPORATION database,
ZAGAT SURVEY database contents,
and ZENRIN CO. database contents
(hereinafter referred to as “Licensors”),
you are bound by the terms and
conditions set forth below.
By using your copy of the DVD, you
have expressed your Agreement to the
terms and conditions of this Agreement.
You should, therefore, make sure that
you read and understand the following
provisions. If for any reason you do not
wish to be bound by the terms of this
Agreement, please return the DVD to
your dealer.
• The DVD may not be copied,
duplicated, or otherwise modified, in
whole or in part, without the express
written permission of the Licensors.
• The DVD may not be transferred or
sublicensed to any third party for
profit, rent or loan, or licensed for
reuse in any manner.
• The DVD may not be decompiled,
reverse engineered or otherwise
disassembled, in whole or in part.
• The DVD may not be used in a
network or by any other manner of
simultaneous use in multiple systems.
• The DVD is intended solely for
personal use (or internal use where
the end-user is a business) by the
consumer. The DVD is not to be used
for commercial purposes.
• The Licensors do not guarantee to the
customer that the functions included
in the DVD meet the specific
objectives of the user.
• Licensor shall not be responsible for
any damages caused by the use of the
DVD to the actual user or to any third
party.
• The warranty on the DVD shall not
extend to an exchange or refund due
to misspelling, omission of letters, or
any other cosmetic discrepancy in the
contents of the DVD.
• The right to use the DVD shall expire
either when the user destroys the
DVD or software, or when any of the
terms of this Agreement are violated
and the Licensors exercise the option
to revoke the license to use the DVD
or software.
8Navigation System
User Agreement
2008 Odyssey 00X31-SHJ-8101
Main Menu
• The terms and conditions hereof
apply to all subsequent users and
owners as well as to the original
purchaser.
• The logos of oil companies, hotels,
and convenience stores are displayed
for your information and
convenience, and in no way implies
any sponsorship, approval or
endorsement of these companies, or
their products. The logos are
trademarks of their respective
owners.
The user shall indemnify and save
harmless the Licensors, and their
officers, employees and agents, from
and against any claim, demand or
action, irrespective of the nature of the
cause of the claim, demand or action,
alleging loss, costs, expense, damages
or injuries (including injuries resulting
in death) arising out of the use or
possession of the DVD or software.
Use, duplication, or disclosure of this
DVD by or on behalf of the United
States government is subject to
“Restricted Rights” as set forth at FAR
52.227-14, -19 or DFARS 252.2277013, as applicable. Manufacturers are
the Licensors, including HONDA
MOTOR CO., LTD., 2-1-1 Minami
Aoyama Minato-Ku Tokyo 107-8556
JAPAN., Alpine Electronics, Inc., 20-1
Yoshima Kogyodanchi, Iwaki,
Fukushima 970-1192 JAPAN.,
NAVTEQ Corporation, 222
Merchandise Mart, Suite 900, Chicago,
IL, 60654, INFO USA
CORPORATION, 5711 South 86th
Circle, Omaha, NE 68127.,
Zagat Survey, LLC, 4 Columbus Circle,
New York, NY, 10019., and ZENRIN
CO., LTD., 1-1-1 Muromachi,
Kokurakita-ku, Kitakyushu, Fukuoka
803-8630, JAPAN.
Navigation System9
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
System Controls
MAP
GUIDE
CANCEL
ENT
ZOOM
ZOOM buttons
Joystick/ENT button
MAP/GUIDE button
CANCEL button
Screen
MENU
INFO
AUDIO
OPEN
SETUP
/CLOSE
SETUP button
MENU button
INFO button
AUDIO button
OPEN/CLOSE
button
CLOCK
MAP/GUIDE button
Displays the map. When on a route,
switches between the map and
guidance screens. See page 20 or 52.
CANCELbutton
Cancels the current screen and returns to
the previous screen display.
NOTE:
the NAVI BACK button performs the
same basic function.
Joystick/ENTbutton
Moves left, right, up and down, to move
the highlighting around the display, to
scroll through lists, or to look around a
displayed map. After making a selection
in a menu or list, push in on the joystick
to enter the selection into the system.
In almost all cases, you can enter a
selection into the system by using the
voice control system, highlighting the
item and pushing in on the joystick, or
by touching the appropriate item you
wish to select.
10Navigation System
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
ZOOM(IN)/(OUT)buttons
Press ZOOMto zoom in (to show
more detail), or ZOOMto zoom out
(to show more area and less detail)
while a map screen is displayed.
ZOOM IN reduces the scale (showing
less area with greater detail). ZOOM
OUT increases the scale (showing more
area with less detail). See page 56.
MENUbutton
Displays the Enter destination by
screen. When on a route, displays the
Change route by screen. See page 23.
INFObutton
Displays the screen for selecting
Cellular Phonebook*, Voice
Command Help, Map Legend,
Calendar, Calculator, and Key to
Zagat Ratings. See page 70.
*Available only for the Touring
model.
AUDIObutton
Press to display the audio screen.
For information on audio system
features, see the Audio section of the
Owner’s manual.
SETUPbutton
Displays the Setup screens to change
and update information in the system.
See page 77.
OPEN/CLOSEbutton
Tilts the screen down to access the CD
changer.
CLOCK
Both the screen clock* and this console
clock are controlled by the Navigation
system and automatically compensate
for daylight savings and time zone
changes during vehicle operation. They
can be adjusted in Setup mode. See
page 97.
*For the screen clock, see page 18.
Screen
All selections and instructions are
displayed on the screen. In addition, the
display is a “touch screen” – you can
enter information into the system by
touching the images (icons) on the
screen with your finger.
For example, if you need to enter a
street name, a keyboard will be
displayed. You can type in the street
name by saying or selecting the
individual characters on the screen.
Clean the screen with a soft damp cloth.
You may use a mild cleanser intended
for use on liquid crystal displays
(LCDs). Harsher chemicals may
damage the screen.
NOTE:
Whenever you shift to R (reverse), the
rear view is shown on the navigation
system screen. See page 100.
Navigation System11
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
Voice Control Basics
Your vehicle has a voice control system
that allows hands-free operation of most
of the navigation system functions. You
can also control the audio system and
the climate control system. The voice
control system uses the NAVI TALK
and NAVI BACK buttons on the
steering wheel and a microphone near
the map light on the ceiling.
NOTE:
While using the voice control system, all
of the speakers (except the RES
headphones) are muted.
Touring model:
HFL
button
NAVI TALK
button
NAVI BACK
button
HFL BACK
button
EX-L model:
NAVI TALK
button
NAVI BACK
button
Microphone
(on the ceiling)
NAVI TALK button
This button activates the voice control
system. Press and release it when you
want to give a voice command. See
Voice Command Index on page 132 for
a list of voice commands.
12Navigation System
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
NAVI BACK button
This button has the same function as the
CANCEL button. When you press and
release it, the display returns to the
previous screen. When the previous
screen appears, the system replays the
last prompt. This button is enabled for
the navigation system commands only.
However, it can be used to cancel an
audio or climate control voice command
up to one second after the command
confirmation.
NOTE:
For the Touring model, the NAVI
TALK and NAVI BACK buttons are
deactivated while using the Bluetooth®
HandsFreeLink® feature. See your
vehicle Owner’s manual and the official
web site (handsfreelink.honda.com) for
information on this system.
Using the Voice Control System
You should use the voice control system
as much as possible, and consider
manual entry using the joystick as a
“back-up” method of entry.
Most of the system’s functions can be
controlled by voice commands activated
with the NAVI TALK button. To
control your navigation system by
voice:
• Press and release the NAVI TALK
button.
• Wait for the beep.
• Give a voice command.
Once the microphone picks up your
command, the system changes the
display in response to the command and
prompts you for the next command.
Using the NAVI TALK button, answer
the prompts as required.
If the system does not understand a
command or you wait too long to give a
command, it responds with “Pardon,”
“Please repeat,” or “Would you say
again.” If the system cannot perform a
command or the command is not
appropriate for the screen you are on, it
sounds a beep.
Anytime you are not sure of what voice
commands are available on a screen,
you can always say “Help” at any
screen. The system can then read the list
of commands to you.
Navigation System13
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
When you speak a command, the system
generally either repeats the command as
a confirmation or asks you for further
information. If you do not wish to hear
this feedback, you can turn it off.
However, hearing the feedback will
familiarize you with the way the system
expects commands to be phrased. See
the Voice Recognition Feedback
setting in Setup.
If you hear a prompt such as “Please use
the touch screen to...” or “Please choose
an area with the joystick,” the system is
asking for input that cannot be
performed using the voice control
system.
Improving Voice Recognition
To achieve optimum voice recognition,
when using either the Navigation or
Bluetooth® HandsFreeLink® voice
control system, the following guidelines
should be followed:
NOTE:
Make sure the correct screen is
displayed for the voice command that
you are using. See Voice Command
Index on page 132.
• Adjust the air flow from both the
dashboard and side vents so they do
not blow against the microphone on
the ceiling. Place your hand over the
microphone; if you feel any airflow,
adjust the vents.
• Lower the A/C fan speed during
voice recognition operation.
• Close the windows and the sunroof.
• After pressing and releasing the
NAVI TALK button, wait for the
beep, then give a voice command.
• Give a voice command in a clear,
natural speaking voice without
pausing between words.
• If the system cannot recognize your
command because of background
noise, speak louder.
• If more than one person is speaking at
the same time, the system may
misinterpret your command.
• If you are still having trouble with the
voice control system, refer to Voice Command Help on the
Information screen.
14Navigation System
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
Selecting an Item (Button)
on the Screen
On most screens, there are items that
can be selected (like buttons with titles
such as OK or Return). To select an
item on any screen, do one of the
following:
• Use the voice control system and say
the name of the desired item. Almost
all selectable items on the screen,
including some listed items, are
recognized by the voice control
system.
• Touch the desired item on the screen.
• Move the highlighting to the desired
item with the joystick, then push in
on the joystick.
Tip:
If items are grayed out (very dark
colored), this means that they cannot be
selected.
Selecting an Item in a List
To scroll through a list, do one of the
following:
• Use the joystick to scroll through the
list item by item.
• Use the voice control system and say
“Next” or “Previous” or use the “on
screen” scroll up or down buttons, or
the ZOOM buttons to scroll through
the list page by page.
If you cannot find the desired name, or
have made an error, return to the
previous screen by pressing the
CANCEL or the NAVI BACK button.
To select the desired item in the list, do
one of the following:
• Use the voice control system, and say
the item number of the desired item.
• Touch the item on the screen.
• Use the joystick to move the
highlighting to the item, then push in
on the joystick.
Navigation System15
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
Using the On-screen
Keyboard
When the system needs input from you,
the display changes to a keyboard. Use
the displayed letters to enter the
information. Enter each letter by one of
the following methods:
• Using the voice control system, say
the desired letter on the screen.
• Move the highlighting to the desired
letter using the joystick, then push in
on the joystick.
• Touch the desired letter on the screen.
When speaking the letters or using
“spell mode,” you can substitute the
name that represents each letter or
symbol. This improves recognition. The
system will only respond to the names
shown in the following graphic.
For example:
• To select the letter “A”: Say, “A”;
“Alpha”; or “Apple.”
• To select the letter “M”: Say, “M”;
“Mike”; or “Mary.”
The names that can be used for each letter are shown below. For additional keyboard
symbols, see page 141.
Alpha
Apple
Kilo
King
Uniform
Uncle
Bravo
Boy
Lima
Larry
Victor
Charlie
Mike
Mary
Whiskey
William
Delta
Dog
November
Nancy
X-Ray
Echo
Edward
Oscar
Yankee
Yellow
Foxtrot
Frank
Papa
Paul
Zulu
Zebra
Golf
George
Quebec
Queen
Henry
Romeo
Robert
Hotel
India
Igloo
Sierra
Sam
Slash
Juliet
John
Tango
Tom
Apostrophe
Ampersand
16Navigation System
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
Each entered letter will appear at the top
of the display. Say or select Space to
enter a space between words. Say or
select Delete to erase a letter entered
incorrectly.
When entering an address, the system
searches the database for words that
match the letters you are entering. As a
result, you will notice that some letters
are no longer available.
When the system finds only one entry
that matches, it completes the entry of
the name for you. If the system finds
more than one entry that matches your
input, the system displays a list.
Tip:
If you are unsure of the spelling of a
name, enter the letters that you are sure
of, and then select List. The system
displays a list of names that most closely
matches your input.
You can choose to have your keyboard
displayed in alphabetized format as
shown below:
Or in a regular keyboard (QWERTY)
format as shown below:
See Keyboard Layout in the Setup
screen (second).
Bluetooth® HandsFreeLink®
(Touring Model Only)
If you have a Bluetooth compatible cell
phone that is “paired,” then CALL on
the Calculate route to screen is
enabled.
When you select CALL, the system
dials the number shown on the screen. If
CALL is not available (dark gray), and
your phone is “paired,” then make sure
the phone has service or that HFL is not
in use; press the HFL BACK button.
For more information on Bluetooth®
HandsFreeLink®, see the vehicle
Owner’s manual and the official web
site (handsfreelink.honda.com).
Navigation System17
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
System Start-up
When you turn the ignition to ON (II), it
takes several seconds for the navigation
system to boot up.
The first screen to appear is the
navigation system globe screen. The
screen then changes to the Disclaimer
screen:
NOTE:
The OK button does not appear
immediately. It appears after the
software is loaded.
Read this disclaimer carefully so you
understand it before continuing. Push in
on the joystick, or touch OK, and the
map screen will appear on the display.
The “OK” cannot be activated by voice.
NOTE:
If you do not select OK, and then enter
the Setup or Information screens, some
items are not available, and will show
up as darkened buttons (grayed out).
See System Function Diagram on
page 22.
If you do not press the joystick or touch
OK, the screen will display the clock
after 30 seconds.
If you are not planning to use the
navigation system at this time, touch
DISPLAY OFF to turn off the screen.
By touching CLOCK TYPE, you can
change the design of the clock screen.
For details of the clock type, see
page 79.
Tip:
For information on the clock
adjustment, see page 97.
18Navigation System
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
To return to the Disclaimer screen,
press the MENU or MAP/GUIDE
button.
If you have entered any Calendar
reminders, they are displayed after you
select OK.
The Calendar reminder screen
remains displayed until you select OK,
Remind Later or press the CANCEL
button.
If you select OK, the reminder will not
show up again. If you wish to have the
reminder show up again later in the day,
touch the Remind Later button.
If you press the CANCEL button, the
message will be displayed the next time
you start the vehicle.
NOTE:
The system will display the current
message and any older or previously
unread messages, with the newest
message listed first.
Navigation System19
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
Map Screen Legend
Map Orientation
(see page 57)
“North Up”
“Heading Up”
GPS Signal Strength
: Best Reception
: Good Reception
Missing: Poor/No Reception
Current Map Scale
(see page 56)
ICON Button (see page 60)
Vehicle Position (see page 63)
(Use voice command “Display the current location.”
or touch the icon to show current location.)
NOTE:
See Map Legend on the Information screen for further explanation.
“Breadcrumbs”
(see Off-road Tracking
on page 62)
Current Street (see page 6)
Landmark Icon - Generic (see page 58)
Honda Dealer
Hospital
Grocery Store
Gas Station
Hotel/Lodging
Parking Garage
Freeway Exit Information
Streets (see Map Overview on page 6)
Red: Interstates or Freeways
Black: Verified Streets
Light Brown: Unverified Streets
One-way Traffic Icon (1/20 mile only)
(see page 61)
Map Features
Dark Green: Park
Light Blue: Hospital
Brown: Shopping Mall
Light Brown: Indian Reservation
Green: Golf Course
Gray: Airport/Stadium/Business
Blue: Body of Water
Blue/Green: Cemetery
Matte Blue: University
NOTE:
If you move the joystick over an area (map
features shown above), the name is displayed on
the screen.
Acura Dealer
School
Restaurant
AT M
Parking Lot
Post Office
20Navigation System
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
Map Screen Description
Zoom In/Out
Use the ZOOM buttons to change the
scale of the map. Zooming in increases
the detail, while zooming out gives you
a wide area view. After changing the
scale, give the system a few moments to
update the display.
Map Scrolling
To view other areas on the map, move
the joystick left, right, up, or down. The
map will shift in that direction. To
return the map to your current location,
press either the MAP/GUIDE, the
CANCEL, or the NAVI BACK button.
Displaying Current Location
You can say “Display current location.”
or touch the vehicle position icon at any
time to see the current address, latitude,
longitude and elevation. The screen will
change to:
NOTE:
The elevation will not appear when the
system is temporarily lacking proper
GPS information. The system elevation
may not agree with elevations shown on
roadside elevation signs, and may
fluctuate plus or minus 100 feet or more.
You can say “Save current location.” or
select Save on the screen to save the
current location in your Address Book.
Select Return to return to the previous
screen.
Navigation System21
Getting Started
2008 Odyssey 00X31-SHJ-8101
Main Menu
System Function Diagram
This diagram shows the navigation
system features, starting at the center
and working outward in layers. The
navigation program starts at “Key ON,”
and then displays the globe screen
(blue). If OK is selected on the
Disclaimer screen, the functions in the
yellow segments of the diagram become
available in the Setup and Information
screens.The white segments of the
diagram are available anytime, even if
you do not select OK.
The items above the map screen show
various methods to begin driving to
your destination (orange). You are
provided with map/voice guidance,
routing cautions, and a direction list.
While driving to your destination, use
the voice control system as much as
possible to interact with the navigation,
audio, and climate control systems
(green).
VOICE:
"HELP"
(ALL)
(pg. 132)
S
D
N
A
M
M
O
AUDIO (pg. 136 - 140)
C
E
C
CLIMATE CONTROL
I
O
V
NUMERIC RATING
(pg. 76)
COST (pg. 75)
ENTER (pg. 73)
LIST (pg. 73)
MATH (pg. 74)
CONVERT (pg. 75)
LIST (pg. 72)
IMPORT, SEARCH
VOICE:
"MENU" (to
change route)
(pg. 65)
VOICE:
"INFORMATION
INFORMATION SCREEN
(pg. 135)
DELETE (pg. 70)
CLIMATE (pg. 71)
SCREEN"
(pg. 70)
-
(
(pg. 140)
KEY TO ZAGAT
RATINGS
CALENDAR
CALCULATOR
,
NAVI AUDIO
R
D
V
/
P
A
M
VOICE:
MAP LEGEND
PHONEBOOK
VOICE HELP
F
o
t
h
e
v
"HOW FAR TO THE
N
I
V
I
G
E
C
I
O
(pg. 46)
"GO HOME"
BUTTON
(pg. 70)
SELECT
BAND/
FREQUENCY
r
m
o
r
e
e
h
i
c
l
e
VOICE:
DESTINATION?"
(pg. 132)
O
T
G
C
N
A
D
I
U
SELECT A
DESTINATION
WITH
JOYSTICK
(pg. 68)
E
H
T
-
INFO
PRESSED
AUDIO
BUTTON
(pg. 11)
VOL
CD
BALANCE
FUNCTIONS
i
n
f
o
r
m
O
a
t
w
n
e
r
'
s
"DISPLAY (OR SAVE)
CURRENT LOCATION"
O
Y
O
R
,
E
P
A
M
M
E
R
R
E
M
I
A
L
C
S
I
L
D
G
E
H
T
OK
NOT
REAR CAMERA
OTHER
AUDIO
BRIGHTNESS
ZOOM IN/OUT
i
o
n
,
s
e
e
m
a
n
u
a
l
VOICE:
(pg.63)
R
U
N
G
I
T
U
VOICE: "FIND
NEAREST..."
ATM, ETC.
(pg. 134)
R
C
S
N
D
E
L
A
C
R
S
E
D
N
I
E
E
R
C
S
S
C
E
B
O
KEY
ON
(REVERSE)
D
E
C
A
E
E
N
A
R
(
p
g
.
1
N
(
p
R
E
E
N
OK
NOT
PRESSED
S
T
U
T
I
O
"MENU" FOR
DESTINATION
SCREEN
(pg. 23)
(
p
9
)
g
.
1
8
)
PRESS
SCREEN
SETUP
(FIRST)
BRIGHTNESS (pg. 77)
VOLUME (pg. 77)
VOICE:
"SET WAYPOINT"
(pg. 65)
I
N
A
T
N
S
,
D
I
R
VOICE:
ENTER
AFTER RESTART
g
(pg. 69)
.
2
0
)
-
OK
SETUP
BUTTON
(pg. 77)
SYSTEM INFO.
COLOR
CONTRAST (pg. 79)
DISPLAY (pg. 78)
VOICE:
"WHAT TIME
IS IT?"
(pg. 132)
I
O
N
E
C
-
T
I
O
N
CONTINUE
DESTINATION
TO THE
(RESUME)
"ZOOM IN/ZOOM OUT"
"HIDE/DISPLAY ICONS"
PERSONAL
ROUTING
GUIDANCE
CLOCK
ADJUSTMENT
VEHICLE
MAP COLOR (pg. 99)
MENU COLOR (pg. 99)
VERSION (pg. 96)
GUIDE. PR
(pg. 79)
O
MPTS
VOICE:
(pg. 136 - 140)
AUDIO
(pg.135, 136)
L
I
S
T
)
VOICE:
(pg. 56, 133)
VOICE:
(pg. 60, 133)
ADD BOOK (pg. 80)
BASIC
UNITS MI/KM (pg. 96)
UNVERIFIED (pg. 87)
AVOID AREAS (pg. 91)
TIME ZONE (pg. 98)
ADJ. TIME (pg. 98)
DAYLIGHT SAV. (pg. 97)
OFF-ROAD TRACKING
CORRECT VEHICLE
(pg. 62, 94)
POSITION (pg. 95)
VOICE:
CLIMATE
FAN, TEMP
PINs (pg. 84)
22Navigation System
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
When you press the MENU button, the
display changes to:
Address (see page 24)
This selection requires you to enter the
city (and possibly the state), and the
address that you want to go to.
Intersection (see page 28)
This selection allows you to enter the
names of two intersecting streets in a
city. This is useful if you know the
general location of your destination, but
not the exact address.
Places (see page 33)
The system has been programmed with
the locations of many businesses, parks,
hospitals, etc. This selection lets you
search these by category, name, phone
number, or Zagat 2007 (for restaurant).
Map Input (see page 39)
This selection allows you to point to a
destination on the map using the
joystick. This allows you to enter a
destination or address that may not be
listed in the database.
Previous Destinations (see page 42)
When you enter a destination with any
of the available selections (except
Address Book and Go Home), the
last 50 destinations are saved by the
system. Use this selection to choose a
destination again.
NOTE:
If Previous Destinations is grayed
out, there is no Previous Destination
entered.
Today’s Destinations (see page 43)
You can enter and sort up to five
destinations and store them in the
Today’s Destination list. You can then
use the Today’s Destination selection.
NOTE:
If Today’s Destinations is grayed
out, there is no Today’s Destination
entered.
Address Book (see page 45)
This selection allows you to select a
stored address. The system can store up
to a combined total of 200 User 1 and
User 2 addresses.
Go Home (see page 46)
This selection allows you to select your
home or a common place as a
destination.
NOTE:
If you have no home address entered,
the system prompts you for one.
Navigation System23
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
By Address
After you select Address from the
Enter destination by screen, the
display changes to:
Tip:
• When entering an address by voice, it
is more efficient to say the city name
first, then the street name.
• When entering an address by touch, it
is usually easier to enter the street
first. A city or cities that the street
appears in will be displayed. For
your convenience, you do not have to
enter both city and street.
NOTE:
If you find that your city is not listed, it
may be part of a larger metropolitan
area. Try entering the street first.
Selecting the State or Province
The state you are in is displayed at the
top of the screen. If your desired
destination is in another state, select
Change State.
The display then changes to the Enter state name screen. Use the voice
control system and say the name of the
state or use the on-screen keyboard to
enter the name of the state.
Selecting the City
This is helpful if the street runs through
several cities, and you know what city
includes the street. The city you are in is
displayed on the screen. If the city you
want is displayed on the screen, say
“Select current city.” If your desired
destination is in another city, say or
enter that city.
By Voice Control:
Say “City” on the Find address by
screen, and the display changes to the
Say city name screen. Say the city
name and the searching will begin.
NOTE:
To improve voice recognition, when
saying the city name, pronounce the
syllables as clearly as possible.
24Navigation System
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
To enter the city name by voice spelling,
say or select CHANGE TO Spell Mode on the Say city name screen,
and the display will change to the Enter city name screen.
Say the city name by saying individual
letters, one at a time.
The system has a talk back function. If
your spoken letter is not recognized, the
system will talk back to you. For
example, if you say “E” but the system
does not recognize the command, it will
ask you “Please select the number of the
input letter from the list” and the
following pop-up box will appear:
You should select a letter by saying the
number.
Alternatively, to improve voice
recognition, you can say “Echo” or
“Edward” instead of “E.”
See page 16 for a list of available words
for each letter.
By Touch Control:
Select City, and the display then
changes to the Enter city name screen.
Use the on-screen keyboard to enter the
name of the city.
The system will display a list of city
names, with the closest match to the
name you entered at the top of the list.
Select the number (1-6) of the desired
city from the list.
Navigation System25
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
If the system does not find an exact
match, select List when you finish
entering the name of the city. Most of
the cities and towns for that state are
listed.
Listings of cities and towns in the nondetailed coverage area may have an
asterisk “*” next to their names. If you
select one, a pop-up box is displayed
saying; “No detailed street data...”, and
a street address cannot be entered (see
Map Coverage on page 110). Try
entering the street first, and then select
the city if available.
Select View Dest. Map and use the
joystick to select an icon, approximate
area, or street you wish to choose as
your destination. Otherwise, a central
location of the city will be selected. If
you select a point of interest (POI) or
road in an unverified area, you may or
may not have routing in these areas. See
Map Overview on page 6.
Selecting the Street
By Voice Control:
After you have selected the city, or if
you say “Street” on the Find address
by screen, the display changes to the
Say street name screen. Say the street
name and the searching will begin.
To enter the street name by voice
spelling, say or select CHANGE TO Spell Mode on the Say street name
screen, and the display will change to
the Enter street name screen.
Say the street name by saying individual
letters or numbers, one at a time.
26Navigation System
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
The system has a talk back function. If
your spoken letter is not recognized, the
system will talk back to you. For
example, if you say “E” but the system
does not recognize the command, it will
ask you “Please select the number of the
input letter from the list” and the
following pop-up box will appear:
You should select a letter by saying the
number.
Alternatively, to improve voice
recognition, you can say “Echo” or
“Edward” instead of “E.”
See page 16 for a list of available words
for each letter.
By Touch Control:
After you have selected the city, or if
you selected Street in the beginning,
the display changes to the Enter street name screen. Use the on-screen
keyboard to enter the name of the street
(like ELM or 42ND) that is your
destination.
To enter the name of a major highway,
you must use the full name, including a
hyphen. For interstates, use an “I” (I-
10). For U.S. highways, use US (US-
18). For state highways, use the two
character state designation (CA-101).
For county roads, use the appropriate
designation (G-2, for example).
Tip:
When entering a street, you do not need
to enter the direction (N, S, E, W) or the
type (St, Ave, etc.). The system will
automatically determine that for you,
based on your entered city and street
number.
The system will display a list of street
names, with the closest match to the
name you entered at the top of the list.
Select the number (1-6) of the desired
street from the list.
Navigation System27
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
Entering the Street Number
After you have completed the street
name, the display changes to the Enter street number screen. Use the voice
control system and say the address
number as a continuous string of
numbers. For example, the address 1527
should be spoken as “One, five, two,
seven.” You can also use the on-screen
keyboard to enter the street number.
Some address numbers may not be
available on the selected street. For
example, let’s say the individual address
ranges for a selected street name are 1 20, and 9,000 - 10,000 with an overall
range shown on the display of 1 to
10,000. If you try to enter a number
outside the individual address ranges
such as 500, the system will show this
number as un-available (grayed out).
• When using the on-screen keyboard,
the system only allows you to choose
available address numbers.
• When using voice control, the system
beeps if you try to select an unavailable (grayed out) address
number.
If you did not select a city in the
beginning, the street name you selected
might appear in more than one city. The
system will give you a list of cities that
the street appears in. Select the desired
city from the list. The system then
displays the Calculate route to screen
(see Driving to Your Destination on
page 47).
Tip:
If the particular address you want
cannot be found, select Map Input and
use the joystick to select the appropriate
location on the map (see By Map Input
on page 39).
Select View Dest. Map and use the
joystick to select an icon, approximate
area, or street you wish to choose as
your destination. Otherwise, a central
location of the street will be selected. If
you select a point of interest (POI) or
road in an unverified area, you may or
may not have routing in these areas. See
Map Overview on page 6.
By Intersection
After you select Intersection from the
Enter destination by screen, the
display changes to:
Tip:
When entering an address, it is usually
easier to enter the street first. A city or
cities that the street appears in will be
displayed. For your convenience, you
do not have to enter both city and street.
28Navigation System
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
NOTE:
• If you find that your city is not listed,
it may be part of a larger
metropolitan area. Try entering the
street first.
• Prior to departure, you can set areas
to avoid. The system then includes
them in its calculations for the
destination you have entered. See
Edit Avoid Area on page 91.
Selecting the State or Province
The state you are in is displayed at the
top of the screen. If your desired
destination is in another state, select
Change State.
The display then changes to the Enter state name screen. Use the voice
control system and say the name of the
state or use the on-screen keyboard to
enter the name of the state.
Selecting the City
This is helpful if the street runs through
several cities, and you know what city
includes the street. The city you are in is
displayed on the screen. If the city you
want is displayed on the screen, say
“Select current city.” If your desired
destination is in another city, say or
select another city.
By Voice Control:
Say “City” on the Find intersection by
screen, and the display changes to the
Say city name screen. Say the city
name and the searching will begin.
To enter the city name by voice spelling,
say or select CHANGE TO Spell Mode on the Say city name screen,
and the display will change to the Enter city name screen.
Say the city name by saying individual
letters, one at a time.
Navigation System29
Entering a Destination
2008 Odyssey 00X31-SHJ-8101
Main Menu
The system has a talk back function. If
your spoken letter is not recognized, the
system will talk back to you. For
example, if you say “E” but the system
does not recognize the command, it will
ask you “Please select the number of the
input letter from the list” and the
following pop-up box will appear:
You should select a letter by saying the
number.
Alternatively, to improve voice
recognition, you can say “Echo” or
“Edward” instead of “E.”
See page 16 for a list of available words
for each letter.
By Touch Control:
Select City, and the display then
changes to the Enter city name screen.
Use the on-screen keyboard to enter the
name of the city.
The system will display a list of city
names, with the closest match to the
name you entered at the top of the list.
Select the number (1-6) of the desired
city from the list.
If the system does not find an exact
match, select List when you finish
entering the name of the city. Most of
the cities and towns for that state are
listed.
Listings of cities and towns in the nondetailed coverage area may have an
asterisk “*” next to their names. If you
select one, a pop-up box is displayed
saying; “No detailed street data...”, and
a street address cannot be entered (see
Map Coverage on page 110).
Select View Dest. Map and use the
joystick to select an icon, approximate
area, or street you wish to choose as
your destination. Otherwise, a central
location of the city will be selected. If
you select a point of interest (POI) or
road in an unverified area, you may or
may not have routing in these areas. See
Map Overview on page 6.
30Navigation System
Loading...
+ 118 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.