The following products and systems on your vehicle emit radio waves when in
operation:
• Adaptive Cruise Control (ACC) with
Low Speed Follow (LSF)*
• Audio system
• Bluetooth
• Bluetooth HandsFreeLink
®
Audio
®
• Collision Mitigation Braking
System™ (CMBS™)*
• Immobilizer system
• Remote transmitter
• Smart entry system*
• Wireless charger*
Each of the above complies with the appropriate requirements or the required
standards of the FCC (Federal Communications Commission) and Industry Canada,
described below:
As required by the FCC:
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
As required by Industry Canada:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
California Perchlorate Contamination Prevention Act
The airbags, seat belt tensioners, and CR-type batteries in this vehicle may contain
perchlorate materials—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for more information.
California Proposition 65 Warning
WARNING: This product contains or emits chemicals known to the state of
California to cause cancer and birth defects or other reproductive harm.
Event Data Recorders
This vehicle is equipped with an event data recorder (EDR). The main purpose of
an EDR is to record, in certain crash or near crash-like situations, such as an air bag
deployment or hitting a road obstacle, data that will assist in understanding how a
vehicle’s systems performed. The EDR is designed to record data related to vehicle
dynamics and safety systems for a short period of time, typically
30 seconds or less. The EDR in this vehicle is designed to record such data as:
• How various systems in your vehicle were operating;
• Whether or not the driver and passenger safety belts were buckled/fastened;
• How far (if at all) the driver was depressing the accelerator and/or brake pedal;
and,
• How fast the vehicle was traveling.
These data can help provide a better understanding of the circumstances in which
crashes and injuries occur. NOTE: EDR data are recorded by your vehicle only if a
non-trivial crash situation occurs; no data are recorded by the EDR under normal
driving conditions and no personal data (e.g., name, gender, age, and crash location)
are recorded. However, other parties, such as law enforcement, could combine the
EDR data with the type of personally identifying data routinely acquired during a
crash investigation.
To read data recorded by an EDR, special equipment is required, and access to the
vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties
such as law enforcement that have the special equipment can read the information if
they have access to the vehicle or the EDR.
The data belong to the vehicle owner and may not be accessed by anyone else
except as legally required or with the permission of the vehicle owner.
Service Diagnostic Recorders
This vehicle is equipped with service-related devices that record information about
powertrain performance. The data can be used to verify emissions law requirements
and/or help technicians diagnose and solve service problems. It may also be
combined with data from other sources for research purposes, but
it remains confidential.
*if equipped
INTRODUCTIONTABLE OF CONTENTS
This Owner’s Guide is intended to help you quickly get acquainted with your
2016 Honda Civic Coupe. It provides basic information and instructions on technology
and convenience features, as well as emergency procedures and how to get assistance.
This guide is for vehicles sold in the United States and Canada. It covers all Civic Coupe
models, so you may find descriptions of features and equipment that are not in your
vehicle. Images throughout this guide are from U.S. vehicles and represent features and
equipment that are available on some, but not all, models.
This guide is not intended to be a substitute for the Owner’s Manual. The Owner
Information CD enclosed in your glove box kit includes the Owner’s Manual, Navigation
Manual, and vehicle and tire warranties in electronic format. This information can be
viewed on a computer (PC or Mac platform) and saved or printed for your reference. You
can also visit owners.honda.com (U.S.) or myhonda.ca (Canada) to view the complete
and most current information.
If you are the first registered owner of your vehicle, you may request a complimentary
printed copy of the Owner’s Manual, Navigation Manual, or Vehicle Warranty within the
first six months of vehicle purchase. To request a copy, visit owners.honda.com (U.S.)
and create or log in to your account. In Canada, please request a copy from your Honda
dealer.
American Honda Motor Co., Inc. strives to be proactive in protecting our environment
and natural resources. By using electronic delivery for a considerable portion of the
information typically found in a vehicle owner’s manual, we are further reducing our
impact on the environment.
Honda Automobile Customer Service
Your authorized Honda dealer should be able to answer any questions you have
about your vehicle. However, if you are dissatisfied with the information you receive,
you can call Honda Automobile Customer Service (see page 150).
Phone (800) 999-1009 (U.S.) or (888) 946-6329 (Canada)
Honda Roadside Assistance
24-hour emergency road service is available to you in the United States and Canada
throughout your 3-year/36,000-mile warranty term. Services include jump starting,
flat tire and lockout assistance, towing, and more (limitations apply).
Phone (866) 864-5211 (U.S.) or (800) 465-7587 (Canada)
Visual Index .................................... 1
Steering Wheel and Nearby Controls ................1
Dashboard, Ceiling, and Other Controls .............2
Safety Information ......................... 3
Important Safety Information ...............................3
Index ............................................ 154
VISUAL INDEX
Quickly locate items in the vehicle’s interior.
Steering Wheel and Nearby Controls
71310
6
1
Lights/turn signals/LaneWatch
button* p. 37, p. 36, p. 108
2
TRIP knob p. 29
Brightness control p. 37
3
Wipers/washers p. 38
4
Cruise control buttons* p. 101Adaptive Cruise Control (ACC) with
Low Speed Follow (LSF) buttons*
p. 102
5
Horn
6
Voice recognition/BluetoothHandsFreeLink buttons p. 73,
p. 76, p. 83
7
Audio controls p. 54
2
5
8
Instrument panel p. 23
48
911
Information display* p. 28Driver Information Interface* p. 29
9
Lane Keeping Assist System (LKAS)
button* p. 104
10
Vehicle Stability Assist (VSA) OFF
button p. 100
Road Departure Mitigation (RDM)
button* p. 105
Collision Mitigation Braking System
(CMBS) button* p. 106
Tire Pressure Monitoring System
(TPMS) button* p. 118
11
Display/information button* p. 29
*if equipped*if equipped
| 1
SAFETYVISUAL INDEX
Dashboard, Ceiling, and Other Controls
71
8
1
Color audio system* p. 57
Display Audio* p. 62
2
Hazard warning button
3
Climate control system/seat heater
buttons* p. 45, p. 46,p. 49
4
USB port p. 52
5
Accessory power socket p. 52
6
Moonroof switch* p. 36
Map lights p. 37
Rearview mirror p. 45
2
6
12
1011
4
59
3
7
Power window switches p. 35Door lock switches p. 34
Door mirror controls p. 45
8
Trunk release button p. 34
9
Hood release handle p. 132
10
ENGINE START/STOP button*
p. 96
11
ECON button* p. 100
12
Electric parking brake switch
p. 98
Automatic brake hold button
p. 99
SAFETY INFORMATION
Your safety—and the safety of others—is very important, and operating this vehicle
safely is an important responsibility. While we strive to help you make informed
decisions about safety, it is not practical or possible to warn you about all the hazards
associated with operating or maintaining your vehicle. Therefore, you must use your
own good judgment.
Important Safety Information
This guide explains many of your vehicle’s safety features and how to use them. Please
read this information carefully. Following the instructions below will also help to keep
you and your passengers safe.
Important Safety Precautions
• Always wear your seat belt.
• Secure all children in the proper restraint system.
• Be aware of airbag hazards.
• Don’t drink and drive.
• Pay appropriate attention to the task of driving safely.
• Control your speed.
• Keep your vehicle in safe condition.
Engaging in cell phone conversation or other activities that keep you from paying
close attention to the road, other vehicles, and pedestrians could lead to a crash.
Remember, situations can change quickly, and only you can decide when it is safe to
divert some attention away from driving.
Safety Messages
When you see the following messages throughout this guide, pay close attention.
You WILL be KILLED or SERIOUSLY HURT if you don’t follow
DANGER
instructions.
You CAN be KILLED or SERIOUSLY HURT if you don’t follow
WARNING
instructions.
You CAN be HURT if you don’t follow instructions.
CAUTION
This information is intended to help you avoid damage to your
NOTICE
vehicle, other property, or the environment.
*if equipped
2 || 3
SAFETYSAFETY
Carbon Monoxide Gas
The engine exhaust from this vehicle contains carbon monoxide, a colorless,
odorless, and highly toxic gas. As long as you properly maintain your vehicle and
follow the instructions set forth below, you will not accumulate dangerous levels of
carbon monoxide gas in the vehicle interior.
Have the exhaust system inspected for leaks whenever:
• The exhaust system is making an unusual noise.
• The exhaust system may have been damaged.
• The vehicle is raised for an oil change.
When you operate a vehicle with the trunk open, airflow can pull exhaust gas into the
interior and create a hazardous condition. If you must drive with the trunk open, open
all the windows and set the climate control system as shown below.
1. Select the fresh air mode.
2. Select the
3. Set the fan speed to high.
4. Set the temperature control to a comfortable setting.
Adjust the climate control system in the same manner if you sit in your parked vehicle
with the engine running.
mode.
WARNING
Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and
even kill you.
Avoid any enclosed areas or activities that expose you to carbon monoxide.
An enclosed area such as a garage can quickly fill up with carbon monoxide gas. Do
not run the engine with the garage door closed. Even when the garage door is open,
drive out of the garage immediately after starting the engine.
Seat Belts
A seat belt is your best protection in all types of collisions. Airbags are designed to
supplement seat belts, not replace them. So even though your vehicle is equipped with
airbags, make sure you and your passengers always wear your seat belts and wear
them properly.
Lap/Shoulder Seat Belts
All five seating positions are equipped with lap/shoulder seat belts with emergency
locking retractors. In normal driving, the retractor lets you move freely while keeping
some tension on the belt. During a collision or sudden stop, the retractor locks to
restrain your body. The rear seat belts also have a lockable retractor for use with
child seats.
The front seats are equipped with automatic seat belt tensioners to enhance safety.
The tensioners automatically tighten the front seat belts during a moderate to severe
frontal collision, sometimes even if the collision is not severe enough to inflate the
front airbags.
Proper Use of Seat Belts
Follow these guidelines for proper use:
• All occupants should sit upright, well back in the seat, and remain in that position
for the duration of the trip. Slouching and leaning reduces the effectiveness of the
belt and can increase the chance of serious injury in a crash.
• Never place the shoulder part of a lap/shoulder seat belt under your arm or behind
your back. This could cause very serious injuries in a crash.
• Two people should never use the same seat belt. If they do, they could be very
seriously injured in a crash.
• Do not put any accessories on the seat belts. Devices intended to improve comfort
or reposition the shoulder part of a seat belt can reduce the protective capability
and increase the chance of serious injury in a crash.
• No one should sit in a seat with an inoperative seat belt or one that does not
appear to be working correctly. Using a seat belt that is not working properly
may not protect the occupant in a crash. Have a dealer check the belt as soon as
possible.
WARNING
Not wearing a seat belt properly increases the chance of a serious injury or
death in a crash, even though your vehicle has airbags.
Be sure you and your passengers always wear seat belts and wear them
properly.
4 || 5
SAFETYSAFETY
Latch plate
Buckle
Latch
plate
Buckle
Seat Belt Inspection
Regularly check the condition of your seat belts as follows:
• Pull each belt out fully, and look for frays, cuts, burns, and wear.
• Check that the latches work smoothly and the belts retract easily. If a belt does
not retract easily, cleaning the belt may correct the problem. Use only mild soap
and warm water. Do not use bleach or cleaning solvents. Make sure the belt is
completely dry before allowing it to retract.
Any belt that is not in good condition or working properly will not provide proper
protection and should be replaced as soon as possible.
A belt that has been worn during a crash may not provide the same level of protection
in a subsequent crash. Have your seat belts inspected by a dealer after any collision.
WARNING
Not checking or maintaining seat belts can result in serious injury or death if
the seat belts do not work properly when needed.
Check your seat belts regularly and have any problem corrected as soon as
possible.
Fastening a Seat Belt
Adjust your seat to the proper position (see page 40), and then follow the below
steps.
1. Pull the seat belt out slowly.
Pull out slowly.
2. Insert the latch plate into the buckle, then tug on
the belt to make sure the buckle is secure. Make
sure that the belt is not twisted or caught on
anything.
3. Position the lap part of the belt as low as possible
across your hips, then pull up on the shoulder
part of the belt so the lap part fits snugly. This lets
Latch
plate
your strong pelvic bones take the force of a crash
and reduces the chance of internal injuries.
4. If necessary, pull up on the belt again to remove
any slack, then make sure that the belt rests
across the center of your chest and over your
shoulder. This spreads the forces of a crash over
the strongest bones in your upper body.
Lap belt as low
as possible.
To release the belt, push the red PRESS button
then guide the belt by hand until it has retracted
completely.
WARNING
Improperly positioning the seat belts can cause serious injury or death in a
crash.
Make sure all seat belts are properly positioned before driving.
Buckle
6 || 7
SAFETYSAFETY
Driver’s
seat
position
sensor
Airbags
Your vehicle is equipped with three types of airbags: front airbags, side airbags, and side
curtain airbags.
Front Airbags (SRS)
The front SRS airbags inflate in a moderate-to-severe frontal collision to help
protect the head and chest of the driver and/or front passenger. They are housed
in the center of the steering wheel for the driver, and in the dashboard for the front
passenger. Both airbags are marked SRS AIRBAG.
SRS (Supplemental Restraint System) indicates that the airbags are designed to
supplement seat belts, not replace them. Seat belts are the occupant’s primary
restraint system.
Advanced Airbags
Your front airbags have advanced features to help reduce the likelihood of airbagrelated injuries to smaller occupants.
The driver’s advanced front airbag system includes
a seat position sensor. If the seat is too far forward,
the airbag inflates with less force, regardless of the
severity of the impact.
If there is a problem with the driver’s seat position
sensor, the SRS indicator will come on and the
airbag will inflate with full (normal) force, regardless
of the driver’s seating position.
The passenger’s advanced front airbag system
has weight sensors. Although Honda recommends
against carrying an infant or small child in front, if
the sensors detect the weight of a child (up to 65 lbs
or 29 kg), the system will automatically turn off the
passenger’s front airbag.
For both advanced front airbags to work properly:
• Do not spill any liquid on or under the seats.
• Do not put any object under the passenger’s seat.
• Make sure any objects are positioned properly on the floor. Improperly positioned
objects can interfere with the advanced airbag sensors.
• All occupants should sit upright and wear their seat belts properly.
• Do not place any cover over any part of the passenger side dashboard.
Passenger’s
seat weight
sensor
Side Airbags
The side airbags help protect the torso and pelvis of the driver or a front passenger
during a moderate-to-severe side impact. They are housed in the outside edge of the
driver’s and front passenger’s seat-backs. Both are marked SIDE AIRBAG.
Side Curtain Airbags
Side curtain airbags help protect the heads of the driver and passengers in outer
seating positions during a moderate-to-severe side impact. The side curtain airbags
equipped in this vehicle are also designed to help reduce the likelihood of partial and
complete ejection of vehicle occupants through side windows in crashes, particularly
rollover crashes.
The side curtain airbags are located in the ceiling
above the side windows on both sides of the vehicle.
Both are marked SIDE CURTAIN AIRBAG.
The side curtain airbags are designed to deploy
in a rollover, moderate-to-severe side impact, or
a moderate-to-severe angled frontal collision. If
the SRS control unit senses that your vehicle is
Side curtain airbag storage
about to roll over, it immediately deploys both side
curtain airbags and activates both front seat belt
tensioners. If the impact is on the passenger’s side,
the passenger’s side curtain airbag deploys even if
there is no passenger in the passenger seat.
To get the best protection from the side curtain
Deployed side curtain airbag
airbags, occupants should wear their seat belts properly and sit upright and well
back in their seats.
Do not attach any objects to the side windows or roof pillars, as they can interfere
with the proper operation of the side curtain airbags.
When side curtain airbags deploy in a frontal collision
One or both side curtain airbags may inflate in a severe frontal collision. In this case,
the side curtain airbags will deploy slightly after the front airbags.
8 || 9
SAFETYSAFETY
*
U.S.
Canada
Important Facts About Your Airbags
Always wear your seat belt properly, and sit upright and as far back from the steering
wheel as possible while allowing full control of the vehicle. A front passenger should
move their seat as far back from the dashboard as possible.
Do not place hard or sharp objects between yourself and a front airbag. Carrying
hard or sharp objects on your lap, or driving with a pipe or other sharp object in your
mouth, can result in injuries if your front airbag inflates.
Do not attach or place objects on the front airbag covers. Objects on the covers
marked SRS AIRBAG could interfere with the proper operation of the airbags or be
propelled inside the vehicle and hurt someone if the airbags inflate.
Do not attach accessories on or near the side airbags. They can interfere with the
proper operation of the airbags, or hurt someone if an airbag inflates.
Do not attach any objects to the side windows or roof pillars. They can interfere with
the proper operation of the side curtain airbags.
Do not cover or replace the front seat-back covers. This can prevent your side
airbags from properly deploying during a side impact
WARNING
An open glove box can cause serious injury to your passenger in a crash,
even if the passenger is wearing the seat belt.
Always keep the glove box closed while driving.
Airbag System Indicators
If a problem occurs in the airbag system, the SRS indicator comes on and a message
appears on the Driver Information Interface*.
SRS (Supplemental Restraint System) indicator
If the indicator comes on at any other time besides
vehicle start-up, or does not come on at all, have the
system checked by a dealer as soon as possible. If
you don’t, your airbags and seat belt tensioners may
not work properly when they are needed.
WARNING
Ignoring the SRS indicator can result in serious injury or death if the airbag
systems or tensioners do not work properly.
Have your vehicle checked by a dealer as soon as possible if the SRS
indicator alerts you to a possible problem.
*if equipped
Passenger Airbag Off indicator
The indicator comes on to alert you that the front
passenger’s front airbag has been turned off. This
occurs when the front passenger’s seat weight
sensors detect 65 lbs (29 kg) or less, the weight of an
infant or small child, on the seat.
Infants and small children should always ride
properly restrained in a back seat.
The indicator also will come on when the front passenger‘s seat is empty; the
passenger’s front airbag will not deploy in a crash.
To ensure the passenger is detected properly, check that:
• There is no child seat or other object pressing against the rear of the seat-back.
• There is no rear passenger pushing or pulling on the back of the front passenger’s
seat.
• The front seat or seat-back is not forced back against an object on the seat or
floor behind it.
• There is no object placed under or beside the front passenger’s seat.
• The occupant is sitting in an upright position and the seat back is not excessively
reclined.
• The occupant is not leaning against the door or center console.
• The occupant’s feet are placed on the floor in front of them.
• There are no objects hanging from the front passenger’s seat.
• Only small, lightweight objects are in the seat-back pocket.
The passenger airbag off indicator may come on and go off periodically if the total
weight on the seat is near the airbag cutoff threshold.
Have your vehicle checked by a dealer as soon as possible if:
• None of the above conditions exist, and the indicator comes on with an adult
riding there.
• The seat is empty and the indicator is off.
Do not allow an adult passenger to ride in the front seat when the indicator is on.
10 || 11
Airbag System Components
1
Two SRS (Supplemental Restraint System) front airbags. The driver’s airbag
is stored in the center of the steering wheel; the front passenger’s airbag is
stored in the dashboard. Both are marked SRS AIRBAG.
2
Two side airbags, one for the driver and one for the front passenger. The
airbags are stored in the outer edges of the seat-backs. Both are marked SIDE
AIRBAG.
3
Two side curtain airbags, one for each side of the vehicle. The airbags are
stored in the ceiling, above the side windows. The front and rear pillars are
marked SIDE CURTAIN AIRBAG.
4
An electronic control unit that, when the vehicle is on, continually monitors
information about the various impact sensors, seat and buckle sensors,
rollover sensor, airbag activators, seat belt tensioners, and other vehicle
information. During a collision, the unit records such information.
5
Automatic front seat belt tensioners. In addition, the driver’s and front
passenger’s seat belt buckles incorporate sensors that detect whether or not
the belts are fastened.
6
A driver’s seat position sensor. If the seat is too far forward, the airbag will
inflate with less force.
7
Weight sensors in the front passenger’s seat. The front passenger’s airbag
will be turned off if the weight on the seat is about 65 lbs (29 kg) or less (the
weight of an infant or small child) or if the seat is empty.
8
Impact sensors that can detect a moderate-to-severe front or side impact.
9
An indicator on the dashboard that alerts you that the front passenger’s front
airbag has been turned off.
SAFETYSAFETY
10
An indicator on the instrument panel that alerts you to a possible problem with the
airbag system or seat belt tensioners.
11
A rollover sensor that detects whether the vehicle is about to roll over and signal
the control unit to deploy both side curtain airbags.
Airbag Care
You do not need to, and should not, perform any maintenance on or replace any
airbag system components yourself. However, you should have your vehicle
inspected by a dealer in the following situations:
When the airbags have deployed
If an airbag has inflated, the control unit and other related parts must be replaced.
Similarly, once an automatic seat belt tensioner has been activated, it must be
replaced.
You should always use new, genuine Honda parts to replace parts after an airbag
deployment. Used, salvaged, aftermarket, or grey-market parts may not work
correctly in a crash.
When the vehicle has been in a moderate-to-severe collision
Even if the airbags did not inflate, have your dealer inspect the following: the
driver’s seat position sensor, weight sensors in the passenger’s seat, front seat belt
tensioners, and each seat belt that was worn during the crash.
Do not remove or modify a front seat without first consulting a dealer
This would likely disable or affect the proper operation of the driver’s seat position
sensor or the weight sensors in the passenger’s seat. If it is necessary to remove
or modify a front seat to accommodate a person with disabilities, contact a Honda
dealer. For U.S. vehicles, call Honda Automobile Customer Service at (800) 999-1009.
For Canadian vehicles, call Honda Canada Customer Relations at (888) 946-6329.
12 || 13
SAFETYSAFETY
Child Safety
Each year, many children are injured or killed in vehicle crashes because they are either
unrestrained or not properly restrained. In fact, vehicle collisions are the number one
cause of death of children ages 12 and under.
The National Highway Traffic Safety Administration and Transport Canada recommend
that all children ages 12 and under be properly restrained in a rear seat. Some states or
provinces/territories have laws restricting where children may ride.
To reduce the number of child deaths and injuries, every state, Canadian province and
territory requires that infants and children be properly restrained when they ride in a
vehicle.
Protecting Child Passengers
• An inflating front or side airbag can injure or kill a child sitting in the front seat.
• A child in the front seat is more likely to interfere with the driver’s ability to safely
control the vehicle.
• Statistics show that children of all sizes and ages are safer when they are properly
restrained in a rear seat.
• Any child who is too small to wear a seat belt correctly must be restrained in an
approved child seat that is properly secured to the vehicle using either the lap belt
portion of the lap/shoulder belt or the lower anchors of the LATCH system.
• Never hold a child on your lap because it is impossible to protect them in the event
of a collision.
• Never put a seat belt over yourself and a child. During a crash, the belt would
likely press deep into the child and cause serious or fatal injuries.
• Never let two children use the same seat belt. Both children could be very
seriously injured in a crash.
• Do not allow children to operate the doors, windows, or seat adjusters.
• Do not leave children in the vehicle unattended, especially in hot weather when
the inside of the vehicle can get hot enough to kill them. They could also activate
vehicle controls, causing it to move unexpectedly.
WARNING
Children who are unrestrained or improperly restrained can be seriously
injured or killed in a crash.
Any child too small for a seat belt should be properly restrained in a child
seat. A larger child should be properly restrained with a seat belt, using a
booster seat if necessary.
WARNING
Allowing a child to play with a seat belt or wrap one around their neck can
result in serious injury or death.
Instruct children not to play with any seat belt and make sure any unused
seat belt a child can reach is buckled, fully retracted, and locked.
Protecting Infants
An infant must be properly restrained in a rear-facing, reclining child seat until the
infant reaches the seat manufacturer’s weight or height limit for the seat, and the
infant is at least one year old. Many experts recommend use of a rear-facing seat for
a child up to two years old if the child’s height and weight are appropriate for a rearfacing seat.
Child seats must be placed and secured in a rear
seating position. Rear-facing child seats should
never be installed in a forward-facing position.
When properly installed, a rear-facing child seat may
prevent the driver or a front passenger from moving
their seat all the way back, or from locking their
seat-back in the desired position. It can also interfere with proper operation of the
passenger’s advanced front airbag system.
If this occurs, we recommend that you install the child seat directly behind the front
passenger’s seat, move the seat as far forward as needed, and leave it unoccupied.
Or, you may wish to get a smaller rear-facing child seat.
WARNING
Placing a rear-facing child seat in the front seat can result in serious injury or
death during a crash.
Always place a rear-facing child seat in the rear seat, not the front.
14 || 15
SAFETYSAFETY
Marks
Rigid type
Lower anchors
Flexible type
Tether Strap
Hook
Anchor
Straight Top Tether Type
Tether Strap
Hook
Anchor
Other Top Tether Type
Protecting Smaller Children
If a child is at least one year old and within the weight range indicated by the child
seat manufacturer, the child should be properly restrained in a firmly secured
forward-facing child seat.
We strongly recommend placing a forward-facing
child seat in a rear seating position.
Placing a forward-facing child seat in the front seat
can be hazardous, even with advanced front airbags
that automatically turn the passenger’s front airbag
off. A rear seat is the safest place for a child.
Placing a forward-facing child seat in the front seat can result in serious
injury or death if the front airbag inflates.
If you must place a forward-facing child seat in front, move the vehicle seat
as far back as possible, and properly restrain the child.
Selecting a Child Seat
Most child seats are LATCH-compatible (Lower Anchors and Tethers for CHildren).
Some have a rigid-type connector, while others have a flexible-type connector. Both
are equally easy to use. Some existing and previously owned child seats can only
be installed using the seat belt. Whichever type you choose, follow the child seat
manufacturer’s use and care instructions as well as the instructions in this manual.
Proper installation is key to maximizing your child’s safety.
In seating positions and vehicles not equipped with LATCH, a LATCH-compatible
child seat can be installed using the seat belt and a top tether for added security.
This is because all child seats are required to be designed so that they can be
secured with a lap belt or the lap part of a lap/shoulder belt. In addition, the child seat
manufacturer may advise that a seat belt be used to attach a LATCH-compatible seat
once a child reaches a specified weight. Please read the child seat owner’s manual
for proper installation instructions.
Important considerations when selecting a child seat
Make sure the child seat meets the following four requirements:
• The child seat is the correct type and size for the child.
• The child seat is the correct type for the seating position.
• The child seat is compliant with Federal Motor Vehicle Safety Standard 213 or
Canadian Motor Vehicle Safety Standard 213.
• The child seat is not older than the expiration date printed on the seat.
WARNING
Installing a LATCH-Compatible Child Seat
A LATCH-compatible child seat can be installed in either of the two outer rear seats.
A child seat is attached to the lower anchors with either the rigid or flexible type of
connectors.
1. Locate the lower anchors under the marks.
2. Place the child seat on the vehicle seat, then
attach the child seat to the lower anchors
according to the instructions that came with the
child seat. Make sure that the lower anchors
are not obstructed by the seat belt or any other
object.
3. Open the tether anchor cover behind the head
restraint.
4. Route the tether strap over the top of the head
restraint, and secure the tether strap hook onto
the anchor.
5. Tighten the tether strap as instructed by the child
seat manufacturer.
6. Make sure the child seat is firmly secured by
rocking it forward and back and side to side; little
movement should be felt.
7. Make sure any unused seat belt that a child
can reach is buckled, the lockable retractor
is activated, and the belt is fully retracted and
locked.
16 || 17
SAFETYSAFETY
Tether
Points
Anchorage
Cover
Anchor
Tether Strap
Hook
Anchor
Straight Top Tether Type in Outer
Position
Tether Strap
Hook
Anchor
Other Top Tether Type in Outer
Position
Tether Strap
Hook
Anchor
Straight Top Tether Type in Center
Position
Tether Strap
Hook
Anchor
Other Top Tether Type in Center
Position
Installing a Child Seat with a Lap/Shoulder Seat Belt
1. Place the child seat on the vehicle seat.
2. Route the seat belt through the child seat
according to the seat manufacturer’s instructions,
and insert the latch plate into the buckle. Insert
the latch plate fully until it clicks.
3. Slowly pull the shoulder part of the belt all the
way out until it stops. This activates the lockable
retractor.
4. Let the seat belt completely wind up into the
retractor, then try to pull it out to make sure the
retractor is locked. If you are able to pull the
shoulder belt out, the lockable retractor is not
activated. Pull the seat belt all the way out, and
repeat steps 3 – 4.
5. Grab the shoulder part of the seat belt near the
buckle, and pull up to remove any slack from
the lap part of the belt. When doing this, place
your weight on the child seat and push it into the
vehicle seat.
6. Make sure the child seat is firmly secured by
rocking it forward and back and side to side; little
movement should be felt.
7. Make sure any unused seat belt that a child
can reach is buckled, the lockable retractor
is activated, and the belt is fully retracted and
locked.
To deactivate a lockable retractor, release the buckle and allow the seat belt to
wind up all the way.
Adding Security with a Tether
A tether anchorage point is provided behind each rear seating position. A child
seat that is installed with a seat belt and comes with a tether can use the tether for
additional security.
1. Locate the appropriate tether anchorage point
and lift the cover.
2. Route the tether strap over the head restraint.
Make sure the strap is not twisted.
3. Secure the tether strap hook onto the anchor.
4. Tighten the tether strap as instructed by the child
seat manufacturer.
18 || 19
SAFETYSAFETY
(SAE J639 J2842 J2845)
Reserve tank cap
U.S. models
(U.S. models only)
Dashboard
Canadian models
Air conditioner system
*
Sun visor
U.S. models
Canadian models
Do not touch bare
metal or white clip.
Metal rod gets hot
and can burn hand.
Always lift rod
using foam area.
GRAB FOAM
Protecting Larger Children
When a child is too big for a child seat, secure the child in a rear seat using the lap/
shoulder seat belt.
Have the child sit upright and all the way back, then ensure the following:
• The child’s knees bend comfortably over the edge
of the seat.
• The shoulder belt crosses between the child’s
neck and arm.
• The lap part of the seat belt is as low as possible,
touching the child’s thighs.
• The child can stay seated for the whole trip.
If a lap/shoulder belt cannot be used properly, position the child in a booster seat in
a rear seating position. For the child’s safety, check that the child meets the booster
seat manufacturer’s recommendations.
Some U.S. states and Canadian provinces/territories require children to use a booster
seat until they reach a given age or weight (e.g., 6 years or 60 lbs). Be sure to check
current laws in the state or province/territory where you intend to drive.
WARNING
Allowing a child age 12 or under to sit in the front can result in injury or death
if the passenger’s front airbag inflates.
If a larger child must ride in front, move the vehicle seat as far to the rear as
possible, then have the child sit up properly and wear the seat belt properly,
using a booster seat if needed.
Safety Label Locations
Safety labels are in the locations shown. They warn you of potential hazards that
can cause serious injury or death. Read these labels carefully.
20 || 21
*if equipped
INSTRUMENT PANELSAFETY
200
323.
4
1234
Menu
4080
Reporting Safety Defects
In the U.S.
If you believe that your vehicle has a defect which could cause a crash or could cause
injury or death, you should immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a
safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
However, NHTSA cannot become involved in individual problems between you, your
dealer, or American Honda Motor Co., Inc.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236
(TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA,
1200 New Jersey Avenue, SE., Washington, DC 20590. You can also obtain other
information about motor vehicle safety from http://www.safercar.gov.
In Canada
If you believe that your vehicle has a defect which could cause a crash or could cause
injury or death, you should immediately inform Honda Canada, Inc., and you may also
inform Transport Canada.
If Transport Canada receives similar complaints, it may open an investigation, and if it
finds that a safety defect exists in a group of vehicles, it may lead to a recall and remedy
campaign. However, Transport Canada cannot become involved in individual problems
between you, your dealer, or Honda Canada, Inc.
To contact Transport Canada’s Defect Investigations and Recalls Division, you may call
1-800-333-0510. For more information on reporting safety defects or about motor vehicle
safety, go to http://www.tc.gc.ca/roadsafety.
INSTRUMENT PANEL
Learn about the indicators, gauges, and displays related to driving the vehicle.
Models with information display
Models with Driver Information Interface
Indicators briefly appear with each engine start and then go out. Red and amber
indicators are most critical. Blue and green indicators are used for general information.
22 || 23
INSTRUMENT PANELINSTRUMENT PANEL
Malfunction Indicators
These are the most critical indicators. If they come on and stay lit while driving or at any
other time, there may be a problem. See your dealer if necessary.
Brake system
U.S.
• Brake fluid is low. Check the brake fluid (see page 137).
• The brake system has a problem. Press the brake pedal lightly to check
Canada
pedal pressure. If normal, check the brake fluid level when you stop. If
abnormal, take immediate action. If necessary, downshift the transmission
to slow the vehicle using engine braking. Have your vehicle checked by a
dealer immediately.
• If the indicator blinks (or comes on simultaneously with the amber brake
system indicator), there is a problem with the electric parking brake
system. Avoid using the parking brake and have your vehicle checked by a
dealer immediately.
Low oil pressure
Engine oil pressure is low. Immediately stop in a safe place. Open the hood.
Check the oil level, and add oil if necessary (see page 133). If the indicator
does not turn off, have your vehicle checked by a dealer immediately.
Charging system
The battery is not charging. Turn off all electrical items, but do not turn off the
vehicle to prevent further battery discharge. Have your vehicle checked by a
dealer immediately.
Supplemental Restraint System (SRS)
There is a problem with one of the airbag systems or seat belt tensioners.
Have your vehicle checked by a dealer immediately.
Smart Entry system*
There is a problem with the system. Have your vehicle checked by a dealer.
Lane Keeping Assist System (LKAS)*
There is a problem with the system. Have your vehicle checked by a dealer.
Electric Power Steering (EPS)
There is a problem with the system.Have your vehicle checked by a dealer.
Malfunction indicator lamp (check engine light)
The emissions control system may have a problem. If the indicator blinks,
a misfire in the engine’s cylinders is detected. Stop in a safe place, and wait
for the engine to cool down. Have your vehicle checked by a dealer.
Anti-lock Brake System (ABS)
There is a problem with the system. Your vehicle still has normal braking
ability, but no anti-lock function. Have your vehicle checked by a dealer.
Tire Pressure Monitoring System (TPMS) (U.S. models)
If the indicator blinks and remains on, there is a problem with the tire
pressure monitoring system, or the vehicle is fitted with the compact spare
tire. If the vehicle battery was disconnected, the system is temporarily
deactivated. Drive a short distance at 12 mph (20 km/h) or more, and the
indicator should go off. If the indicator remains on, have your vehicle
checked by a dealer.
Vehicle Stability Assist (VSA)
There is a problem with the VSA system or hill start assist system. If the
vehicle battery was disconnected, the system is temporarily deactivated.
Drive a short distance at 12 mph (20 km/h) or more, and the indicator should
go off. If the indicator remains on, have your vehicle checked by a dealer.
Vehicle Stability Assist (VSA) OFF
If the vehicle battery was disconnected, the system is temporarily
deactivated. Drive a short distance at 12 mph (20 km/h) or more, and the
indicator should go off. If the indicator remains on, have your vehicle
checked by a dealer.
Collision Mitigation Braking System (CMBS)*
There is a problem with the system, the temperature is too high, or the
camera is blocked. If the indicator remains on, have your vehicle checked
by a dealer.
Starter system*
There is a problem with the system. Press and hold the ENGINE START/STOP
button for up to 15 seconds while pressing the brake pedal to manually start
the engine. Have your vehicle checked by a dealer.
Brake system
SYSTEM
There is a problem with one of the braking systems, the electric parking
U.S.
brake system, or the automatic brake hold system. Have your vehicle
checked by a dealer.
Canada
Adaptive Cruise Control (ACC) with Low Speed Follow (LSF)*
There is a problem with the system. Have your vehicle checked by a dealer.
Road Departure Mitigation (RDM)*
There is a problem with the system. Have your vehicle checked by a dealer.
*if equipped
24 || 25
*if equipped
INSTRUMENT PANELINSTRUMENT PANEL
Canada
Condition Indicators
These indicators may require you to perform an action.
Parking brake
U.S.
Release the parking brake before driving. You will hear a beep if you drive
with it not fully released.
Canada
Seat belt reminder
Make sure seat belts are fastened for you and all passengers. The indicator
blinks and beeps sound continuously if you or your front passenger has not
fastened your seat belts when you begin driving. If the indicator remains on
after seat belts are fastened, see your dealer.
Door/trunk open
A door or the trunk is not closed. A beep sounds if open while driving.
Low fuel
Refuel as soon as possible. If the indicator blinks, there is a problem with the
fuel gauge. Have your vehicle checked by a dealer.
Low tire pressure*
Stop in a safe place, check tire pressures, and inflate tire(s) if necessary.
The indicator also appears if the system has not been calibrated (see page
118).
Washer fluid level*
The washer fluid is low. Refill the washer fluid (see page 137).
Brake depress
Press the brake pedal before applying or releasing the electric parking
CVT models
brake or automatic brake hold. A blinking indicator means automatic brake
MT models
hold operation ceased. Immediately press the brake pedal.
On/Off Indicators
These indicators remind you when an item is on or off.
VSA off
VSA engaged (blinking)
CRUISE MAIN on
CRUISE CONTROL on
ACC* on
CMBS* off
LKAS* on
Turn signals/hazards on
Fog lights* on
High beams on
Exterior lights on
ECON mode on
Automatic brake hold on
Automatic brake hold
U.S.
activated
System message*
When a condition or malfunction indicator comes on, a message also
appears on the Driver Information Interface. Check the display for more
information. Press the display/information button on the steering wheel to
clear the message.
Maintenance Minder*
Scheduled maintenance for your vehicle is due.
Immobilizer/security system
Your key or remote transmitter cannot be recognized by the vehicle. If the
indicator blinks, you may not be able to start the engine. Turn the vehicle
off, remove the key from the ignition*, press and hold the brake pedal, and
restart the vehicle. If it continues to blink, there may be a problem with the
system. Have your vehicle checked by a dealer.
Canadian models: To reset the immobilizer system, follow the steps above
after the battery has been disconnected.
*if equipped
26 || 27
INSTRUMENT PANELINSTRUMENT PANEL
(TRIP) knob
Display/Information button
(TRIP) knob
Driver Information
Interface
Information Display*
Consists of several displays that provide you with useful information.
Press the TRIP knob to cycle through the displays shown below.
Instant fuel economy
Odometer
Trip meter A
Outside temperature
Engine oil life
Instant fuel economy
Range
Trip meter A
Outside temperature
Instant fuel economy
Average fuel economy A
Trip meter A
Outside temperature
Instant fuel economy
Average fuel economy B
Trip meter B
Outside temperature
Driver Information Interface*
Consists of several displays that provide you with useful information.
Main Displays
Press the display/information button to scroll through the different icons shown
below. Detailed information for the selected icon appears after a few seconds, or you
can press the ENTER button to view it.
Range/
average fuel
Turbo
Meter
*
Compass /
Navigation
*
Maintenance
*
Minder™
Audio
AAAAA
Phone
*
Change Unit
(or blank)
*
Warning
Messages
Trip Computer
Cycle between the trip meters by pressing the TRIP knob.
OdometerTrip ATrip B
*if equipped
28 || 29
*if equipped
VEHICLE CONTROLSINSTRUMENT PANEL
MENU/CLOCK Button
Audio/Information Screen
Selector Knob
(Phone) Button
Audio/Information
Touch Screen
Vehicle Settings
You can customize certain features when the vehicle is stopped.
Models with Information Display
Models with Driver Information Interface
VEHICLE CONTROLS
Learn about the various controls necessary for operating and driving the vehicle.
Using the Key or Remote Transmitter*
Lock or unlock the doors and trunk.
Unlock button: Press once to
unlock the driver’s door. Press
again to unlock all doors.
Engine button*: Remotely start
the engine (see page 94).
Built-in key*: Slide the
release knob on the back
of the transmitter and
pull out the built-in key.
Lock button: Press to lock
the doors. Press again for
audible verification.
Trunk button: Press and
hold to unlock and open
the trunk.
Panic button: Press to
sound the alarm for 30
seconds. Press again to
cancel.
Release knob
Built-in key
NOTICE
Leaving the key or remote transmitter in the vehicle can result in theft or accidental
movement of the vehicle. Always take it with you whenever you leave the vehicle
unattended.
30 || 31
*if equipped
VEHICLE CONTROLSVEHICLE CONTROLS
Door Lock Button
Button
Trunk Release
Smart Entry System*
When you carry the remote transmitter (for example, in a pocket or purse) and it is
outside the vehicle and within range (about 32 inches or 80 cm), you can lock or unlock
the doors and trunk without handling the transmitter.
Unlocking/Locking the Doors
To unlock: Grab the driver’s door handle when the
vehicle is off to unlock the driver’s door. Grab the
front passenger’s door handle to unlock all doors.
To lock: Press the door lock button on either
door handle when the vehicle is off. If the remote
transmitter is inside the vehicle, the doors will not
lock.
Unlocking the Trunk
Press the trunk release button to unlock and open
the trunk.
Walk Away Auto Lock*
When you walk away from the vehicle while carrying the remote transmitter, the
doors can automatically lock if the following conditions are met:
• The remote transmitter is within a range of 6 feet (2 m).
• All doors and the hood are closed.
• There is not an additional remote transmitter inside the vehicle.
When you are within the range, the system is activated and a beep sounds. When
you go outside the range, the lights flash and a beep sounds again. The doors
automatically lock.
To turn on this feature, follow the steps below:
1. From the HOME screen, select Settings.
2. Select Vehicle. The vehicle must be in Park (P).
3. Select Door/Window Setup.
4. Select Walk Away Auto Lock.
5. Select On.
6. Select BACK to exit the menus.
*if equipped
32 || 33
*if equipped
VEHICLE CONTROLSVEHICLE CONTROLS
To unlock
Lock tab
To lock
To Unlock
Lock Switch
Master Door
To Lock
Trunk Release
Button
Power
Window Lock
Button
Indicator
Driver’s
Window
Passenger’s
Door Operation
Use several methods to lock or unlock the doors.
Using the Lock Tab
To unlock: Pull the lock tab rearward. When you
unlock the door using the lock tab on the driver’s
door, only the driver’s door unlocks.
To lock: Push the lock tab forward. When you lock
the door using the lock tab on the driver’s door, the
other door locks at the same time.
Using the Door Inner Handle
When you pull a door inner handle, the door unlocks
and opens. Unlocking and opening the driver’s door
from the inner handle unlocks the other door.
Using the Master Door Lock Switch
To unlock: Press the unlock side of the switch to
unlock both doors.
To lock: Press the lock side of the switch to lock
both doors.
Power Window Operation
The power windows can be opened and closed when the vehicle is on by using the
switches on the doors. The switches on the driver’s side can be used to open and close
both windows.
Automatic Operation
To open: Push the switch down firmly.
To close: Pull the switch up firmly.
The window opens or closes completely. To stop the
window at any time, push or pull the switch again
briefly.
Manual Operation
To open: Push the switch down lightly.
To close: Pull the switch up lightly.
Release the switch when the windows reach the desired position.
Power Window Lock
Push in the power window lock button so only the driver’s window can be operated.
WARNING
Closing a power window on someone’s hands or fingers can cause serious
injury.
Make sure your passengers are away from the windows before closing them.
Using the Trunk Release Button
Press the trunk release button on the driver’s door to
open the trunk.
34 || 35
VEHICLE CONTROLSVEHICLE CONTROLS
Open
Close
Tilt
TRIP knob
Door-activated position
Off
Front
High beams
Flash the high beams
Low beams
Fog
lights*
Power Moonroof Operation*
The moonroof can be opened and closed when the vehicle is on by using the switch on
the ceiling.
Automatic Operation
To open: Push the switch back firmly to the second
detent, then release.
To close: Push the switch forward firmly to the
second detent, then release.
The moonroof opens or closes completely. To stop
the moonroof at any time, push the switch briefly.
Manual Operation
To open: Push and hold the switch back to the first detent until the desired position is
reached.
To close: Push and hold the switch forward to the first detent until the desired
position is reached.
Moonroof Tilt
To tilt: Push the center of the switch.
To close: Push the switch forward firmly, then release.
WARNING
Closing the moonroof on someone’s hands or fingers can cause serious injury.
Make sure your passengers are away from the moonroof before closing it.
NOTICE
Opening the moonroof in below freezing temperatures or when it is covered with
snow or ice can damage the moonroof panel or motor.
One-Touch Turn Signal
Use this quick and convenient method to signal a lane change.
Lightly push the turn signal lever up or down for a
three-blink sequence.
For a continuous signal, push the lever up or down
until it locks into place.
Interior and Exterior Lights
Operate interior and exterior lights when the vehicle is on or off.
Brightness Control
Adjust instrument panel brightness when the vehicle is on.
To brighten: Turn the knob to the right.
To dim: Turn the knob to the left.
A beep sounds when the brightness reaches its
minimum or maximum.
Interior Lights
Change the interior light settings using the front and rear switches on the ceiling.
ON position (rear): Interior lights remain on.
Door-activated position (front): Interior lights come
on when any of the doors are opened, the driver’s
door is unlocked, or the vehicle is turned off.
OFF position: Interior lights remain off.
Map lights: Press the map lights to turn on or off.
Exterior Lights
Rotate the switches on the headlight lever to operate the exterior lights.
OFF: All exterior lights are off.
: Turn on exterior lights except headlights.
AUTO: Turn on the automatic lighting feature.*
Headlights turn on or off depending on ambient
brightness when the vehicle is on. Headlights
automatically come on after the wipers are
engaged for a certain time.
: Turn on all exterior lights including headlights.
: Turn fog lights* on or off.
Map lights
36 || 37
*if equipped
*if equipped
VEHICLE CONTROLSVEHICLE CONTROLS
Rotate the
adjustment ring.
Lower speed,
fewer sweeps
Higher speed,
more sweeps
INT position
Rotate the
adjustment ring.
Low sensitivity:
Wipers operate when
more rainfall is detected.
High sensitivity:
Wipers operate when
less rainfall is detected.
AUTO position
Wiper Operation
The windshield wipers and washers can be used when the vehicle is on. Move the wiper
lever up or down to the desired position.
MIST
OFF
INT: Low speed intermittent
LO: Low speed wipe
HI: High speed wipe
Headlight-Wiper Integration*
When the headlights are in the AUTO position, they automatically turn on when the
front wipers operate several times within a certain interval. The headlights turn off
shortly after the wipers are turned off, or if there is enough ambient light.
NOTICE
Do not use the wipers when the windshield is dry. The windshield may scratch, or
the rubber blades may become damaged.
In cold weather, the blades may freeze to the windshield, becoming stuck.
Operating the wipers in this condition may damage the wipers. Use the defroster
to warm the windshield, or manually clear the windshield of ice and snow before
turning on the wipers.
Pull to
use
washer.
Intermittent (INT) Wipers*
When you move the lever to the INT position, the
wipers operate based on the delay adjustment.
Rotate the adjustment ring to adjust the wiper delay.
Automatic (AUTO) Rain-Sensing Wipers*
When you move the lever to the AUTO position while
driving in rainy weather, the wipers operate based
on the amount of detected rainfall.
Put the lever in the AUTO position only when driving
in rainy weather.
Rotate the adjustment ring to adjust the rainfall
sensor sensitivity.
Return the lever to the OFF position when rain stops.
NOTICE
Always ensure the wiper lever is in the OFF position before entering a car wash to
prevent severe damage to the windshield wiper system.
38 || 39
*if equipped
*if equipped
Adjusting the Seats
Horizontal position
adjustment
Pull up on the bar to move the
seat, then release the bar.
Height adjustment
(driver side only)
Pull up or push down the lever
to raise or lower the seat.
Seat-back angle
adjustment
Pull up the lever to
change the angle.
Make seat adjustments before driving to ensure the best comfort and safety.
Adjusting the Seats
Adjust the driver’s seat as far back as possible while
allowing you to maintain full control of the vehicle.
You should be able to sit upright and well back in the
seat, adequately press the pedals without leaning
forward, and grip the steering wheel comfortably.
The passenger’s seat should be adjusted in a similar
manner, so that it is as far back from the front airbag
in the dashboard as possible.
The National Highway Traffic Safety Administration and Transport Canada
recommend that drivers allow at least 10 inches (25 cm) between the center of the
steering wheel and their chest.
Move back and allow
sufficient space.
VEHICLE CONTROLSVEHICLE CONTROLS
WARNING
Reclining the seat-back too far can result in serious injury or death in a crash.
Adjust the seat-back to an upright position, and sit well back in the seat.
WARNING
Sitting too close to a front airbag can result in serious injury or death if the
front airbags inflate.
Always sit as far back from the front airbags as possible while maintaining
control of the vehicle.
WARNING
Sitting improperly or out of position can result in serious injury or death in a
crash.
Always sit upright, well back in the seat, with your feet on the floor.
Floor Mats
Position the front seat floor mats properly, and
anchor them. If they are not properly positioned, the
floor mats can interfere with the front seat functions.
Do not put additional floor mats on top of the
anchored mats.
Unlock
Lock
40 || 41
VEHICLE CONTROLSVEHICLE CONTROLS
Lever
Release
Release Lever
Seat-back Angle
Adjustment Lever
Seat-back Angle
Adjustment Lever
Release Lever
Adjusting the Head Restraints
Your vehicle is equipped with head restraints in all seating positions. Head restraints
are most effective for protection against whiplash and other rear-impact crash
injuries.
The center of the back of the occupant’s head
should rest against the center of the restraint. The
tops of the occupant’s ears should be level with the
center height of the restraint.
To raise the head restraint: Pull it upward.
To lower the head restraint: Push it down while
pressing the release button.
To remove the head restraint: Pull the restraint up as
far as it will go. Then push the release button, and
pull the restraint up and out.
To reinstall a head restraint: Insert the legs back
in place, then adjust the head restraint to an appropriate height while pressing the
release button. Pull up on the restraint to make sure it is locked in position.
In order for the head restraint system to work properly:
• Do not hang any items on the head restraints, or from the restraint legs.
• Do not place any object between an occupant and the seat-back.
• Install each restraint in its proper location.
WARNING
Improperly positioning head restraints reduces their effectiveness and
increases the likelihood of serious injury in a crash.
Make sure head restraints are in place and positioned properly before driving.
Rear Seat Access
Driver side: Pull up the seat-back lever to tilt the
seat-back forward.
Passenger side: Pull up the seat-back lever, or push
the seat-back release lever, to tilt the seat-back
forward. Then move the seat forward.
Folding Down the Rear Seats
The rear seat-backs can be folded down to make room for large items in the trunk.
1. Pull the release lever in the trunk to release the
lock.
2. Fold down the seat-back.
Push the seat-back up firmly until it locks into
place to return it to its original position.
Make sure all items in the trunk or items
extending through the opening into the rear
seats are properly secured. Loose items can fly
forward if you have to brake hard.
WARNING
Failure to reinstall, or correctly reinstall, the head restraints can result in
severe injury during a crash.
Always replace the head restraints before driving.
42 || 43
Loading...
+ 57 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.