Honda Accord Wagon 1991 Owner's Manual
1991 Accord Wagon Online Reference Owner's Manual
Use these links (and links throughout this manual) to navigate through this reference.
For a printed owner's manual, click on authorized manuals or go to www.helminc.com.
Owner's Identification Form
Features & Safety ................................................................................................................................ 2
What you should know before driving your car.
Starting & Driving............................................................................................................................. 65
What gas to use, how to change gears, etc.
Maintenance ....................................................................................................................................... 85
The Required Maintenance Schedule and some items you can service.
Emergency Service .......................................................................................................................... 122
Changing a flat, jump starting, towing.
Specifications ................................................................................................................................... 130
Dimensions, weights and capacities.
Consumer Information .................................................................................................................... 132
Reporting Safety Detects, warranty service, vehicle identification numbers, etc.
Index ................................................................................................................................................ 140
Contents
Introduction
This manual contains important information about the safe operation
and maintenance of your car.
We urge you to read this manual carefully, become familiar with the
controls it describes, and follow its recommendations, to help make
your driving trouble-free and enjoyable.
Statements or labels on the product preceded by the following words
are of special significance:
indicates severe personal injury or death will
result if instructions are not followed.
indicates a strong possibility of severe personal
injury or death if instructions are not followed.
means hazards or unsafe practices which could
cause minor personal injury or product or property damage.
NOTE: gives helpful information.
Break-in Period
During the first 600 miles (1,000 km) of driving, avoid full-throttle
starts and cruising for extended periods at a constant speed.
NOTE:
This break-in procedure also applies to exchanged or overhauled
engines.
During and after the break-in period, drive the car at moderate
speeds until the engine is fully warmed up.
During the first 200 miles (300 km), try to avoid severe braking.
Brake misuse during this period will reduce future braking efficiency.
Remember, your Honda Automobile dealer knows your car best, and
should be consulted for service assistance and advice.
Keys and Locks
Master and Valet Keys
Your car is supplied with a master
key that fits the ignition and all locks,
and a valet key that fits the ignition
and doors, but not the glove box or
tailgate. The valet key is provided for
times when you must leave the key
with a parking attendant or repair
person, but still want to keep
valuables safely locked-up in the
glove box.
Write down the numbers stamped on all of the keys and keep the
information in your wallet or purse in case you ever need to have
duplicates made. All keys are double-edged so you can insert them
into the locks with either side up.
Using the Master and Valet Key
If a key is used to lock the driver's side
door, all doors and the tailgate will
lock, but the key will only unlock the
driver's door.
If a key is used in the front passenger
door, all doors and the tailgate will
lock and unlock.
Using the key in the tailgate will lock
and unlock the tailgate and all doors.
To open the tailgate, pull the handle, then lift up.
VALET KEY
Lock
MASTER KEY
Unlock
Lock
Unlock
Keys and Locks (cont'd)
Remote Access Key
(US Cars: EX, Canada Cars: EX-R)
In addition to the master and valet keys, your
car is also supplied with a battery-operated
remote access key. Use the remote access key
to activate the keyless entry system.
Keyless Entry System
The keyless entry system enables you to operate the locks from
outside the car without inserting the key in the keyhole.
The battery in the remote access key recharges each time the key is
in the ignition with the engine running.
Using the Remote Access Key
(US: EX, Canada: EX-R)
To operate the door locks from
outside the car using the remote
access key, aim the key blade at the
keyless entry window located to the
left of the keyhole in the driver's
door or tailgate, and press the
button in the key. Keep the key
blade within 18 inches (50 cm) and
in line with the keyless entry
window. When the remote access
key is used on the driver's door, all
doors and the tailgate will lock; but
only the driver's door will unlock.
KEYLESS ENTRY WINDOW
KEYLESS
ENTRY
WINDOW
If the remote access key is used on
the tailgate, the tailgate and all
doors will lock and unlock.
Replacement Key
If you lose your remote access key, you can order a replacement from
your Honda dealer. You need the five-digit keyless code number on the
aluminum plate that came with your key and the four-digit number
on the key blade. Both numbers are equally important and should be
stored in a safe yet accessible place.
Take care in handling the remote access key; its electric circuit is very
sensitive.
- Avoid dropping heavy objects on the key.
- Keep the key away from areas with high temperatures, high
humidity and direct sunlight.
- Do not disassemble the key.
- Use only a mild detergent and water to clean the key; dry the key
thoroughly with a soft cloth.
- Use the remote key as your main ignition key. This will allow the
battery to be regularly recharged.
The remote access key will not operate if:
Dirt or moisture is on the key or keyless
entry window.
The key was not used in the ignition regularly and has lost its
charge.
Consult your dealer if the keyless entry does not operate properly.
Keys and Locks (cont'd)
Door Plunger
From inside the car, each door and the tailgate can be locked by
pushing the plunger down; each door can be unlocked by pulling the
plunger up.
Pushing down the plunger on the driver's door locks all doors and the
tailgate, but pulling up the plunger unlocks only the driver's door.
Pushing down on the tailgate plunger locks the tailgate and all doors.
The plunger on the tailgate is not designed to be pulled up manually
for unlocking.
Unlock
Lock
Unlock
Lock
Power Door Locks
All doors and the tailgate can be simultaneously locked and unlocked
by operating the master door lock switch on the inside of each front
door.
Unlock
Lock
Lockout Prevention
Lockout Prevention keeps you from locking the driver's door or the
tailgate when the key is in the ignition and the driver's door or
tailgate is open. If you try to lock the driver's door by pushing down
the plunger, the tailgate plunger and all other door plungers will pop
back up. If you push down the tailgate plunger when the key is in the
ignition and the tailgate is open, the tailgate plunger and all other
door plungers will pop back up. Also, both master door lock switches
will not lock the doors if either front door is open and the key is in the
ignition.
The system can be overridden if the outside or inside door handle is
held in the open position while the plunger is pushed down. The lock
cycles several times and may lock all doors and the tailgate after the
door is closed .
Lockout Prevention does not affect the operation of any passenger
door lock.
(US Cars: EX, Canada Cars: EX-R)
Lockout Prevention does not affect the operation of the Remote Access
Key.
Child Proof Door Locks
The child proof door locks are designed to prevent accidental opening
of the rear doors from inside the car. To activate the locks, push down
the lock tabs located on each rear door, then close the doors. When the
rear doors are locked in this way, they can only be opened from the
outside.
LOCK TAB
Seats
Front Seat
Adjust the seat position by pulling up on the adjustment lever under
the front edge of the seat cushion, and sliding the seat to the desired
position. Then release the lever and make sure the seat is locked in
position by moving it back and forth.
Pull up
Pull up
The angle of the seat-back can be changed by pulling up on the lever
at the outside edge of the seat and leaning forward or back. Release
the lever and let the seat lock into place when it reaches the desired
angle.
Seat belts are most effective when the driver and passengers are
sitting up straight and well back in each seat.
Do not adjust the driver's seat while the car is moving; the seat
could move suddenly, causing loss of vehicle control.
To reduce the risk of sliding under the seat belts in a collision,
the seat-backs should be reclined no more than is necessary for
comfort.
Driver's Lumbar Support
(US: EX, CANADA: EX-R)
To adjust for more or less support of the
driver's lower seat-back cushion, turn
the knob on the inner side of the
seat-back.
Do not try to adjust the lumbar
support while driving. Make the adjustment
while sitting in your normal driving
position before driving away.
Head Restraints
The head restraints are designed to help reduce injuries due to
whiplash. They are located at the top of each front seat-back and have
several height positions. The restraints can be adjusted by pulling up
to the recommended position. To lower them, slide the button next to
the restraint's height adjustment bar while pushing the restraint
down. Adjust so the top of the restraint is approximately level with
the tops of your ears.
If a head restraint must be removed (for cleaning, fabric repair, etc.)
pull the restraint up to its highest position, then slide the button
while pulling the restraint out.
To reinstall, reverse the above procedure.
Slide
Do not drive the car with head restraints removed.
Do not try to adjust head restraints while driving.
Rear Seat Arm Rest
The rear seat arm rest located at
the rear seat-back can be used by
pulling the tab.
Seats (cont'd)
Folding Rear Seat
Each rear seat-back can be folded down to provide more cargo space.
Folding both rear seat-backs down will provide maximum cargo
space.
1. Pull on the strap at the center of the seat to lift up the seat
cushion.
STRAP
2. Remove the head restraint from the rear seat-back by sliding the
button next to the head restraint's height adjustment bar and
lifting the head restraint out.
Slide
3. Pull up the release knob at the top of the seat-back and fold the
seat forward.
Pull up
4. Store the head restraint in the holes provided in the seat cushion.
Weight limits shown on the label attached to the driver's door
jamb must be observed. The total weight of passengers and
cargo must not exceed the total weight limit on the label.
Make sure the rear seat-back latches engage securely when the
seat-back is returned to its normal position.
Always replace the head restraints when the seat-back is
returned to its upright position.
When transporting luggage or other cargo do not pile it higher
than the front seats. This precaution will help prevent such items
from becoming dangerous projectiles in an accident.
Cargo weight should be distributed as far forward as possible for
better vehicle handling.
Loading the Car
The maximum your car can carry, including passengers, cargo, and
trailer tongue weight, is 950 Ibs (431 kg). This is the Vehicle Capacity
Weight noted on the tire label attached to the driver's door jamb.
To calculate the car's load capacity, start with 950 Ibs (430 kg). First
subtract 150 Ibs (68 kg) for each person, including the driver. For
example, if there will be five people in the car (750 Ibs, 340 kg), you
can carry up to 200 Ibs (91 kg) of cargo.
If you are towing a trailer, remember to also subtract the trailer
tongue weight (see page 78) from the 950 Ibs (430 kg) capacity.
After you have determined how much cargo you can carry, remember
that where you put cargo is also important. Do not load cargo above
the top of the rear seat-back. The maximum you can carry behind the
rear seat is 200 Ibs (91 kg). To maintain a better weight distribution,
place heavier items toward the center of the car.
CAUTION:
Do not exceed the maximum weight capacity for your car;
overloading may affect vehicle handling and tire life.
Load cargo so it will not contact the printed defroster wires in the
rear window. The wires may be damaged if the cargo rubs against
them.
Cargo Area
A passenger should never sit in the open cargo area while the car is
moving. They should sit in one of the seats and wear their seat belt.
With the rear seats folded, the length of the cargo area is 72 in (1850
mm). The width at the tailgate opening is 36 in (915 mm). The width
between the wheel wells is 30 in (775 mm). The height of the rear
opening is 28 in (725 mm).
28
in.
(725 mm)
Storage Compartments
You can store smaller items in any of the
three storage compartments in the cargo
area. Two compartments are under the carpet, on either side of the tire compartment.
The third is in the right side panel.
Tonneau Cover
When extended, the tonneau cover con-
ceals your parcels and protects them
from direct sunlight. To extend the tonneau cover, pull the cover's leading edge
out of its housing and slip the brackets
over the hooks provided at both sides of
the tailgate opening.
Slip
bracket
over
hook.
STORAGE
COMPARTMENT
LOCATIONS
To retract the cover, slip the brackets off
the hooks and guide the cover so it rolls
back fully into its housing.
CAUTION: Do not store parcels on the
tonneau cover. The tonneau cover may
break if weight is placed on it.
TONNEAU
COVER
Cargo Area (cont'd)
Package Net
The package net is intended to restrain only
light, soft items, such as clothing which do not
exceed a total weight of 10 Ibs (4.5 kg).
Grasp the net's leading edge and pull it out of
the tonneau cover housing. Lock the prongs
at both ends of the net into either the floor or
ceiling latches.
To store the net, release both prongs from the
latches and let it roll back into the tonneau
cover housing.
You can select from either of two locations to position the tonneau cover
housing unit. One position is directly
behind the rear seat and the other is
halfway between the rear seat and
the tailgate.
To remove the housing unit, depress
HOUSING
UNIT
LOCATIONS
the latch on the right end of the unit
and pull the unit out of the bracket,
then pull the opposite end out of its
LATCH
bracket.
CAUTION: Make sure all objects in the cargo area are secured,
otherwise they may become projectiles in an accident.
NET
BRACKET
Secure the tonneau cover housing unit when you are not using it. Use
the two straps located in the right side floor storage compartment and
strap it to the two floor hooks closest to the tailgate opening in the cargo area. If it is not secured, it may become a dangerous projectile in
an accident.
1. Take one strap and loop the free end through a floor hook.
2. Place the housing on the strap and wrap the strap completely
around it.
3. Slip the free end through the "D" rings, then separate the rings
and slip the strap over one ring and under the other and pull tight.
Repeat this procedure for the other strap and hook.
Seat Belts
Your Honda automobile is provided with seat belts to minimize the
chance of injury to yourself and your passengers in a sudden stop or
accident.
For precautions on using seat belts for children, babies, and pregnant
women, see pages 18 - 20.
Seat belts are most effective when properly worn and when the driver
and passengers are sitting up straight and well back in their seats.
in the event of a collision, occupants not wearing seat
belts could be seriously or fatally injured. Make sure you and all
your passengers ALWAYS put on the seat belts before driving away.
CAUTION: Be careful the seat belts are not damaged in the door or
seat mechanism.
Buckling the Front Seat Belts
The front seat belts are one-piece combination lap/shoulder belts with
emergency locking retractors designed to lock only during a sudden
stop or impact. Otherwise, they allow you some freedom of movement
in the seat.
NOTE: The emergency locking retractor will also activate if the belt
is pulled too fast. If the belt locks, release the belt slightly and pull it
out more slowly.
1. Before buckling your belt, move the seat to a comfortable distance
from the steering wheel, sit straight up and well back in your seat.
2. Take hold of the tongue plate and
pull the belt across your lap. Be sure
the belt is not twisted or caught on
anything.
Seat Belts (cont'd
3. Push the tongue plate into the buckle until
it clicks locked. Position the belt across your
lap, not your abdomen, as low on your hips as
possible.
)
Avoid placing the lap belt across
your abdomen. In the event of a collision, the
pressure of the belt on the abdomen may
increase the extent of injury.
4. To release the belt, push the "PRESS" button in the buckle; the belt
should retract automatically when released. If the belt does not
fully retract, pull it out and check for kinks or twists.
Comfort clips sold on the open market are not recommended
since they could impair the function and safety of the belts.
Do not wear the shoulder portion of the belt under your arm or
out of position. Such use could increase the chance and amount
of injury in an accident.
Never use one belt for more than one person, child or adult.
Shoulder Anchor Height Adjusting Mechanism
The height of the shoulder anchor can be
adjusted to four positions. It is best to use the
shoulder belt at the highest adjustment
position. However, if the belt is too near your
neck, causing discomfort, lower the anchor
position one step at a time until the belt is in a
comfortable position.
To raise or lower the anchor height adjustment,
push the release tabs on the mechanism.
Release
tab
Release
tab
Buckling the Rear Seat Belts
In the rear seat, there are two one-piece combination lap/shoulder
belts and a center lap belt. The seat-backs and seat belts provide best
restraint when the occupants are sitting well back and straight up in
the seat.
The lap/shoulder belts work the same as the two front seat belts.
Make sure both rear shoulder belts are positioned in front of the rear
seat-backs whenever the seat-backs are in their upright positions.
To use the center lap belt, push the tongue plate into the buckle until
it clicks locked. Position the belt across your lap, not your abdomen
and as low on your hips as possible. Pull the loose end of the belt to
adjust for a snug but comfortable fit.
A slack belt will greatly reduce the protection afforded to the wearer.
Hold the tongue plate perpendicular to the belt as shown.
To shorten, pull the end of the belt away from the tongue plate.
To lengthen, pull the tongue plate.
TONGUE PLATE
To lengthen
To shorten
BUCKLE
NOTE: When the center lap belt is not in use, store it in the buckle
locators.
Fasten Seat Belt Warning Light and Warning Beeper
Both the light in the
instrument panel and the warning
beeper will go on for about six seconds
when the ignition switch is turned on
and the driver's belt is not fastened.
The beeper will not go on if the
driver's seat belt is fastened before
the ignition switch is turned on, but
the warning light will come on for
about six seconds each time, to
remind the driver to have passengers put their seat belts on. If the
light and beeper do not work as described, have your dealer check the
system.
Seat Belts (cont'd)
Child Restraint
Children riding in the car should be restrained to minimize the risk
of injury in an accident, sudden stop or sudden maneuver.
According to accident statistics provided to the National Highway
Traffic Safety Administration (NHTSA), children are safer when
properly restrained in the rear seating positions than in the front
seat.
For smaller children, we strongly recommend the use of a
commercially available child restraint system that meets the Federal
Motor Vehicle Safety Standard (FMVSS) and the applicable Canadian
Motor Vehicle Safety Standards because it offers the most protection
against injury. All states and virtually all provinces in Canada now
have laws which require that small children must be seated in a child
passenger seat restraint system. Check local laws.
All child restraint systems are designed to be secured by lap belts or
the lap portion of a lap-shoulder belt. Children could be endangered
in a crash if their restraints are not properly secured.
Before buying a particular child restraint system, make sure it fits
your car seat and seat belts, and fits your child. Follow the child seat
manufacturer's instructions when installing the seat.
Children who have outgrown the child restraint system should use
one of the seat belts.
Make sure the belt is snug against the child's body with the
shoulder portion going over the shoulder and across the body to
evenly distribute the belt's restraining force.
Check that the lap portion of the belt is positioned low on the child's
hipbone and below the abdomen. This way if the car is involved in
an accident, the child will be less likely to slide under the seat belts.
If the belt is too close to the child's neck or throat, you may want
to consider putting the child in an automobile booster seat that
meets the Federal Motor Vehicle Safety Standard (FMVSS).
Children should never ride unrestrained in an automobile.
Never use an infant carrier or child safety seat that "hooks" over
a seat-back; it may not provide adequate security in an accident.
Never allow a child to be held in a person's arms while they are
in the moving vehicle. Holding a child in a moving vehicle does
not provide the child with any means of protection during an
accident, even if the person holding the child is wearing a seat
belt.
Do not allow children to ride in the cargo area of the car.
Installation of Child Seat
All child restraint systems are designed to be secured by lap belts or
the lap portion of a lap/shoulder belt.
Children could be endangered in a crash if their child restraints are
not properly secured. Follow the child seat manufacturer's
instructions when installing the seat.
Your Honda automobile is equipped
with attachment points specifically
for a rear seat mounted child
restraint system which uses a top
tether.
The tether attachment points are
located on the floor just in front of the
tailgate.
TETHER
ATTACHMENT
POINTS
When the child restraint system is not in use, remove
it from the car or secure it with the seat belt to keep it from becoming
a projectile in the event of an accident.
NOTE: See your Honda dealer for installation of the child restraint
system.
Seat Belts (cont'd)
U.S. Cars
The child seat's manufacturer provides the anchor plate and
attaching hardware if the child seat requires a top tether. An anchor
plate kit is also available if you write to:
American Honda Motor Co., Inc.
Consumer Affairs
1919 Torrance Blvd.
Torrance, CA 90501-2746
Anchor Bolt Torque: 16 Ib. ft.
Canadian Cars
Your car is supplied with one child seat tether anchor plate stored in
the glove box. Bolt size: M8 x 1.25. Bolt torque: 22 N.m (2.2 kg-m). If
you are not sure how to install the anchor plate, or you need additional
anchor plates, contact your Honda dealer.
Do not remove the toothed washer
from the child seat anchor plate. Use
the child seat anchor plate with the
toothed washer attached to it.
TOOTHED WASHER
Do not use the anchor plate for any other purpose; it is designed
exclusively for the installation of a child seat.
Make sure the rear seat-back is locked firmly when installing a
child seat.
Pregnant Women
A pregnant woman should use a lap/shoulder belt to help lessen the
chance of injury and/or the amount of injury in an accident.
It is desirable that a pregnant woman ask her doctor at
each medical check-up if she can drive, and also ask about the most
appropriate way of wearing the lap/shoulder belt. If a rear seat lap
belt is used, it should be worn as low and snugly as possible over
the hips.
Inspection
All parts of the seat belts, including the belt fabric, should be
regularly inspected for fraying, loosening, wear and other damage.
Keep the belts in good condition at all times to reduce the chance of
being injured in an accident, and to minimize any injuries that do
occur. Make sure the buckles, retractors, tongue plates, guides and
anchors all work properly.
Don't let anything get inside the buckle or the retractor; it could cause
latch or retractor failure.
Cleaning
The belts should always be kept clean and dry; wet or damp belts can
cause rewinding problems. To clean the belts, pull them all the way
out of their retractors and scrub them with warm water and a mild
soap; then let them air-dry fully extended, in the shade, with the car
windows open.
Never bleach, dye or clean the belts with chemical solvents; they
will weaken the fabric.
Do not remove the seat belts from the car to wash them.
Replacement
Replace the seat belt if:
1. The belting is cut, punctured, burned, etc.
2. The buckle or retractor does not work properly.
3. It was being worn at the time of a collision (also check for
deformation damage at the seat belt anchor points).
4. Its condition is questionable.
Supplemental Restraint System (Airbag)
(US Cars Only)
Your car is equipped with a Supplemental Restraint System (SRS).
The Supplemental Restraint System consists of an airbag and a knee
bolster.
NOTE: The Supplemental Restraint System can function only when
the ignition switch is in the II position.
COMPONENTS of SRS
AIRBAG
ASSEMBLY
LEFT DASH SENSOR
Honda recommends the use of seat belts by all vehicle occupants to
reduce the risk of injury in an accident. The SRS, in combination with
the seat belt, is most effective when used in conjunction with the seat
belt.
KNEE BOLSTER
RIGHT DASH
SENSOR
SRS CONTROL UNIT
Make sure you and your passengers always put on
your seat belts before driving away. See pages 15 - 17 for seat belt
information.
The SRS is designed to deploy in an accident involving a moderate to
severe frontal collision, and is not designed to assist the driver in a
side impact, rear impact or roll-over accident.
The driver and all passengers should wear their seat belts at all times
for maximum protection.
The SRS is designed to function on a one time only basis. In the event
the SRS deploys, the airbag module will not function again and must
be replaced. As a reminder, the SRS indicator light will stay on
continuously after deployment. Only an authorized Honda dealer
should repair or replace the system.
To avoid accidental deployment of the system or
rendering the system inoperative, which may result in serious
injury in an accident, no modifications should be made to any
components or wiring of the SRS. This includes the installation of
"custom" steering wheels or additional trim material, or badges
over the steering wheel hub. Installation of additional
electrical/electronic equipment on or near SRS components and/or
wiring is specifically ill-advised, except by an authorized Honda
dealer.
System Monitors
A diagnostic system continually monitors the readiness of the SRS
while the car is being driven. The SRS indicator light will show normal
system operation by lighting for about 6 seconds when the ignition
key is turned to position II.
The following components are monitored by the diagnostics.
Right Dash Sensor Airbag Activator
Left Dash Sensor All Related Wiring
SRS Control Unit
SRS INDICATOR LIGHT
In the event of a malfunction, promptly take the car to your nearest
Honda dealer to have the system checked. Unless checked and
repaired, the SRS will not function reliably. A malfunction is shown
by:
The indicator light flashing or flickering.
The SRS indicator light failing to illuminate when the ignition
switch is first turned to the II position.
The SRS indicator light continuously illuminated.
The SRS indicator light illuminated while driving.
Supplemental Restraint System (cont'd)
Safety Guidelines for the Supplemental Restraint System
During a severe frontal impact, a sudden, fairly loud inflation noise
will be heard and some smoke and powder will be released, neither
of which is injurious. The smoke from the airbag deployment does not
indicate a fire in the vehicle.
Although it is highly unlikely that the SRS would activate in a
non-accident situation - should it occur, the bag will deflate quickly,
not obscure vision and will not interfere with the driver's ability to
maintain control of the automobile.
NOTE: When you sell your car, we urge you to explain to the buyer
that it is equipped with a Supplemental Restraint System by alerting
him to the applicable section in this owner's manual.
System Servicing
To ensure its long-term reliability, the Supplemental Restraint
System must be inspected by a Honda dealer ten years after the date
of manufacture, which is shown on the certification label attached to
the left rear door jamb.
CAUTION: The impact sensors are located on the left and right
sides of the bulkhead behind the engine. If you need service or
repair in those areas or near the steering wheel and column, have
an authorized Honda dealer do the work.
After a collision that requires the airbag unit or the entire car to
be scrapped, it is mandatory that an authorized Honda dealer use
the procedures and tools described in the Honda Service
Manual.
The SRS has no user-serviceable parts. Tampering with or
disconnecting the SRS wiring could result in accidental firing of
the inflator or could make the system inoperative, which may
result in serious injury in an accident. For required servicing of
the SRS, see your nearest Honda dealer.
Instrument Panel
CRUISE CONTROL
MASTER SWITCH
COIN
BOX
HOOD
RELEASE
HANDLE
TACHOMETER
FUSE
BOX
SUNROOF
SWITCH
IGNITION
SWITCH
TILT STEERING
ADJUSTMENT
LEVER
SPEEDOMETER
WIPER/WASHER
SWITCH
HAZARD
WARNING
SWITCH
ASHTRAY
PANEL
BRIGHTNESS
CONTROL
KNOB
SRS
MAINTENANCE
INDICATOR LIGHT
HEATING/
COOLING
CONTROL
PANEL
CIGARETTE
LIGHTER
FUEL
GAUGE
DIGITAL
CLOCK
REAR
WINDOW
DEFOGGER
SWITCH
GLOVE BOX
SHIFT LEVER
POSITION
INDICATOR
(Automatic Trans. only)
COOLANT
TEMPERATURE
GAUGE
MAINTENANCE
INDICATOR
RESET
MAINTENANCE
INDICATOR
LIGHT
ODOMETER
TRIP METER
TRIP METER
RESET BUTTON
DOOR AND
LAMP
MONITOR
LIGHT
Gauges
Speedometer
US Cars: The speed is indicated in miles per hour (outer scale) and
kilometers per hour (inner scale).
Canada Cars: The speed is indicated in kilometers per hour (outer
scale) and miles per hour (inner scale).
Odometer
The numbers on the odometer indicate miles (US Cars) or kilometers
(Canada Cars).
The odometer registers total distance traveled, and serves as your
guide for determining when periodic maintenance is due.
US Cars: Federal law makes it illegal to alter the odometer of any
motor vehicle with the intent to change the number of miles indicated.
Trip Meter
The numbers on the trip meter indicate miles (US Cars) or kilometers
(Canada Cars).
The trip meter can be returned to zero by pushing in the reset button.
Use the trip meter to check fuel consumption or distance traveled per
trip.
Tachometer
The tachometer indicates engine speed in revolutions per minute.
The beginning of the RED ZONE indicates the maximum allowable
engine R.P.M. Do not run the engine with the tachometer indicator
needle in the RED ZONE.
Fuel Gauge
FUEL TANK CAPACITY: Approx. 64.5 (14.1 Imp. gal, 17.0 US gal)
As a convenience, the gauge continues to show the same fuel level as
when the ignition was last on. After refueling, the gauge will slowly
change to the new fuel level when the ignition is switched on.
When the needle indicates E (empty), a usable reserve of about 4
(0.9 Imp gal, 1.1 US gal) remains in the tank.
Coolant Temperature Gauge
Do not remove the radiator cap when the engine is hot.
The coolant Is under pressure and may blow out and scald you.
This gauge shows the temperature of the engine coolant. During
normal operation, the needle should stay in the middle of the white
range. Under severe driving conditions, such as hot weather or
driving uphill for a long period, the needle may rise toward the upper
section of the white range.
If the needle reaches the red line at "H" (Hot), pull safely off the road
and stop the engine.
Wait until the engine is cool and check the coolant level in the reserve
tank on the passenger side of the radiator under the hood. (See pages
97 - 98.)
Indicator Lights
US Car
Shown:
Shift Lever Position Indicator (Automatic transmission only)
A lighted indicator between the fuel and water temperature gauges
shows which gear you have selected.
S
Indicator Light
The S (Sports) indicator light will come on when the "Sports" switch
on the shift lever is pushed. See page 77.
NOTE: The S indicator light in the instrument panel also serves a
second function. If the light flashes while driving (in any gear range)
it indicates a possible malfunction in the transmission; avoid rapid
acceleration and have the transmission checked by an authorized
Honda dealer as soon as possible.
Turn Signal/Hazard Warning Indicator Lights
When the turn signal lever is pushed for left or right turns, the
appropriate green indicator arrow on the instrument panel will blink
along with the signal. Turning on the hazard warning switch makes
all turn signals and both arrows blink (see page 39).
Headlight High Beam Indicator Light
This blue indicator light will go on whenever the high beams are
switched on (see page 38).
CRUISE
CONTROL
When the cruise control system is engaged, this indicator light is on
(see page 41).
Cruise Control Indicator Light
Fuel Reserve Light
If the light glows, it means you have about 10.0 (1.8 Imp gal, 2.6
US gal) or less fuel remaining and should refuel.
US
Canada
BRAKE
Check the brake light every time you start the car. With the parking
brake set, the warning light should go on when the ignition switch is
turned to I I or I I I.
g o on when the ignition switch is turned to II I.
an y other time, it means the brake fluid level in the master cylinder
reservoir is too low; add fluid (see page 101) and have your dealer
check for leaks immediately. Make sure the parking brake is released
and the light is off before driving away.
Parking Brake/Brake Failure Light
With the parking brake released, the light should
If the light goes on at
Seat Belt Warning Light
The seat belt reminder light comes on for approximately six seconds
when the ignition switch is turned on (see page 17).
Oil Pressure Light
A severe fluctuation in engine oil pressure will cause this light to flash
on and off. You should get off the road as soon as possible and turn
off the ignition. Check the oil level and add oil if necessary.
The oil pressure light will come on, and remain on, if there is
insufficient oil pressure or when the ignition switch is turned on with
the engine not running. If the light should come on while driving, get
the car off the road as soon as you can, turn the engine off and check
the engine oil level (see page 92).
Even if the oil level is correct, the engine should be checked by a
Honda dealer before the car is driven again.
NOTE: The oil pressure light will only light as a result of low oil
pressure. It is not directly an oil level indicator.
CAUTION: Running the engine while the oil pressure light is on
constantly may cause immediate and severe engine damage.
Indicator Lights (cont'd)
Charging System Warning Light
The charging system warning light comes on when there is a problem
with the electrical charging system or when the ignition switch is
turned on with the engine not running. If the light comes on while
driving, stop the car, turn off the engine and check the alternator belt
for proper tension. With the engine turned off, push down on the
middle of the belt as shown; it should have 10-12 mm (0.4 - 0.5 in)
deflection under a force of 98 N.m (22 Ib).
if the engine has been running, some engine components may
be hot enough to burn you.
Keep hands away from the radiator fan. The fan may start
automatically without warning and run for up to 15 minutes, even
after the engine is turned off.
NOTE: If necessary, have the charging system checked by an
authorized Honda dealer.
US
Canada
Check Engine Warning Light
This light comes on for a couple of seconds each time the ignition is
turned on. It will also come on, and remain on, if there is a
malfunction in the emission control system. If the light comes on
while driving, avoid driving at high speed, and have the system
checked by a Honda dealer as soon as possible.
Loading...