HONDA 08E91-E22-100B User Manual

INSTALLATION

www.collegehillshonda.com

INSTRUCTIONS

Accessory Application Publications No.

REMOTE ENGINE

STARTER SYSTEM

2006-2008 CIVIC 2-DOOR

(A/T ONLY)

AII 38215-38958

Issue Date

FEB 2008

PARTS LIST

Remote Engine Starter Unit Kit P/N 08E91-E22-100B

Transmitter

Control unit

Antenna

Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B

Engine starter harness

Control unit bracket

Relay bracket

Key ring

Protective tape

Engine starter label

Fuse label

Accessory User’s Information Manual

Quick Start Guide

3 Black relays (4-pin)

18 Wire ties

7 Foam cushion tapes

www.collegehillshonda.com

Flange nut

Clip

Green relay (5-pin)

Template

Illustration of the Engine Starter System Installed on the Vehicle

RELAY (5-PIN)

2 FUSES 40 A

ANTENNA

ENGINE STARTER HARNESS

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Long blade flat-tip screwdriver

Small flat-tip screwdriver

6 mm Hex wrench

T25 Torx bit

3 mm and 7 mm Drill bit

File

Ratchet

10 mm Socket

Combination wrench

Isopropyl alcohol

Shop towel

Tape measure

Clip remover

Diagonal cutters

Felt-tip pen

Center punch

Scissors

2 Pairs of needle nose pliers

Rubber mallet

HDS (Honda Diagnostic System)

Masking tape

Safety goggles

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

NOTE: The antenna should only be installed if the ambient air temperature 15°C (60°F) or above.

1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

CONTROL UNIT

3 RELAYS (4-PIN)

2 FUSES 3 A

7507010T

Setting the Control Unit

CONTROL UNIT

SMALL FLAT-TIP SCREWDRIVER

Discharge any static electricity.

The switches must be selected before the control unit is plugged in.

SET

SWITCHES

SW:1 RR Junction unit -----------------------> OFF

SW:2 Trunk or Tailgate ----------------------> OFF

SW:3 Smart Entry -----------------------------> OFF

SW:4 Horn or Buzzer Answerback ------> OFF

SW:5 Trunk Main SW -------------------------> OFF

SW:6 Reserve ----------------------------------> OFF

SWITCHES

www.collegehillshonda.com

3. Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the control unit to the locations shown. Using a isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.

SW : 1 RR Junction Unit SW : 2 Trunk or Tailgate SW : 3 Smart Entry SW : 4 Horn or Buzzer Answer Back SW : 5 Trunk Main SW SW : 6 Reserve

NOTE:

• The switches must be selected before the

control unit is plugged in.

• If the switch setting is not correct, the engine

starter will not operate correctly.

• If setting the switches when the control unit is

installed in the vehicle, touch a metal part of the screwdriver to a metal part of the vehicle to discharge any static electricity.

• If you change the switch settings with the unit

connected, you must disconnect the unit then reconnect it before the settings will change.

Removing the vehicle parts

4. Remove the trunk lid/fuel fill door opener cover (six retaining tabs). Remove one self-tapping screw.

KEY

SELFTAPPING SCREW

Unlock.

COVER

TRUNK LID/ FUEL FILL DOOR OPENER

6 RETAINING TABS

5202191T

5. Using the key, unlock the opener.

www.collegehillshonda.com

6. Remove the left front door sill trim (two retaining tabs, five clips, and three hooks).

3 HOOKS

5 CLIPS

2 RETAINING TABS

FRONT

8. If equipped, remove the driver’s dashboard under cover (turn the knob counterclockwise, and release two clips and pin).

DRIVER’S

2 CLIPS

DASHBOARD UNDER COVER

KNOB

5202112T

LEFT FRONT DOOR SILL TRIM

5202200T

7. Pull away the weatherstrip, and remove the left kick panel (two clips).

WEATHERSTRIP

2 CLIPS

LEFT KICK PANEL

9. Remove the driver’s dashboard lower cover (eight clips).

DRIVER’S DASHBOARD LOWER COVER

8 CLIPS

5202121T

5202220T

10. Lower the tilt lever, and pull the steering wheel

www.collegehillshonda.com

toward you. Insert a long blade flat-tip screwdriver along the guide of the column lower cover, and pry the retaining tab of the column upper cover.

2 RETAINING TABS

Push.

COLUMN UPPER COVER

2 HOOKS

COLUMN

RETAINING TAB

LOWER COVER

12. Remove the column lower cover (two self-tapping screws and one screw).

COLUMN LOWER COVER

2 SELF-TAPPING

SCREW

SCREWS

5308530T

TILT LEVER

GUIDE

LONG BLADE FLAT-TIP SCREWDRIVER

6608050T

11. Push on the column lower cover in the area shown to separate the column upper cover from the column lower cover (two retaining tabs). Pull up to remove the column upper cover (two hooks).

13. If equipped, use a small flat-tip screwdriver to

www.collegehillshonda.com

remove the left and right lens from the map light console (four retaining tabs for each lens). Remove the two bolts, and then release the map light console.

FRONT

MAP LIGHT CONSOLE

15. Remove the cap from the left sunvisor (four retaining tabs).

CONNECTOR

4 RETAINING TABS

BOLT

LENS

6D01390T

14. Remove the sunvisor holders. Using a small flattip screwdriver, push the hook, and turn the holder 90°, then pull it out.

MAP LIGHT CONSOLE

CAP

TORX SCREW

LEFT SUNVISOR

5217030T

16. Remove the left sunvisor (two T25 Torx screws, and unplug the vehicle connectors).

17. Pull away the weatherstrip from the left front pillar trim.

Strike perpendicularly to the vehicle.

FRONT PILLAR

FRONT PILLAR TRIM

CLIP

STRIKE POINT

SHOP TOWEL

LEFT FRONT PILLAR TRIM

SUNVISOR HOLDER

SMALL FLAT-TIP SCREWDRIVER

WEATHERSTRIP

6D01400T

18. Using a rubber mallet and a shop towel, gently tap the left front pillar trim at the position shown to

CLIP

release the clip. Gently tap the pillar trim at the area marked as “SIDE CURTAIN AIRBAG”.

RUBBER MALLET

7503020T

19. Pull away the weatherstrip from the left front pillar

7503030T

6D01210T

www.collegehillshonda.com

trim. Remove the left front pillar trim (two clips).

Installing the Antenna

21. Using scissors, cut out the template.

LEFT FRONT PILLAR TRIM

WEATHERSTRIP

2 CLIPS

5202100T

20. Remove the clip from the left front pillar trim, and install a new clip on the left front pillar trim.

NEW CLIP

TEMPLATE

SCISSORS

Cut out.

22. Secure the template to the windshield with the tape by aligning it with the edge of the black ceramic paint as shown.

LEFT FRONT PILLAR TRIM

CLIP (Discard.)

5217110T

BLACK CERAMIC PAINT

WINDSHIELD TEMPLATE

TAPE

EDGE OF BLACK CERAMIC PAINT

Align the end with the end of the black ceramic paint.