HONDA 08B26-S5T-1000-91 User Manual

Accessory Application Publications No.

www.collegehillshonda.com/parts

INSTALLATION

CD CHANGER

A TTA CHMENT KIT

INSTRUCTIONS

PARTS LIST

CD Changer Attachment Kit (sold separately): P/N 08B26-S5T-100

CD changer bracket

2 CD changer plates

2002-2005 CIVIC SI

3 EPT seals

4 Cushion tapes

8 Cap nuts, 6 mm

4 Washer-screws, 4 x 8 mm

4 Clip-nuts, 6 mm

AII 27936

Issue Date

AUG 2004

Template A

Left side bracket

Right side bracket

Bus cable

4 Stepped bolts, 6 mm

Template B

13 Wire ties

08B26-S5T-1000-91

6-Disc CD Changer (sold separately): P/N 08A26-1B1-100

Illustration of the CD Changer Installed in the Vehicle

CD changer

4 W asher-scre ws, 4 x 6 mm (Not used)

Adhesive seal sheet

Cover plates

CD magazine

Owner’s Manual

BUS CABLE

CD CHANGER

AUDIO UNIT

INST ALLATION

Customer Information: The information in this

installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver Flat-tip screwdriver Shop towel 10 mm Combination wrench Stubby Phillips screwdriver Diagonal cutters Utility knife Safety goggles Pushpin Drill 3 mm, 7.5 mm, and 10 mm Drill bits Uni-bit 30 mm Awl Masking tape Electrical tape or drill stop Isopropyl alcohol

1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

3. Open the glove box. Lower the glove box by releasing the right and left glove box stops.

TABS (2)

GLOVE BOX STOPS (2)

Lower.

4. Remove the driver's dashboard low er cover . Turn the lock knob 90° counterclockwise. Gently pull down on the left side of the cover to release the two hooks, then pull down on the cover to release the three retaining tabs. Take care not to damage the retaining tabs.

6. Remove the shift lever trim:

• Pull the shift boot down, and remove the shift knob by turning it counterclockwise.

• Reach through the shift boot, and gently pull out on the shift lever trim to release the bottom of the trim. Lift up on the shift lever trim to release the five hooks and four clips.

• Unplug the hazard warning switch connector, and remove the shift lever trim.

RETAINING TAB

HOOK

RETAINING TAB

KNOB (Turn 90° counterclockwise.)

DRIVER'S DASHBO ARD LOWER CO VER

5. Remove the driver's dashboard under co ver . T urn the lock knob 90° counterclockwise, and pull down on the rear of the cover to release the left clip. Pull the cover out toward you to release the remaining clip. Take care not to damage the clips.

KNOB (Turn 90° counterclockwise.)

CLIPS (4)

SHIFT LEVER TRIM

SHIFT KNOB

HAZARD WARNING SWITCH CONNECTOR

HOOKS (5)

SHIFT BOOT

Reach through the shift boo t, and pull the shift lever trim out

CLIP

DRIVER'S DASHBO ARD UNDER COVER

LEFT CLIP

toward you.

7. Remove the vehicle harness clip from the center panel bracket by pushing up on the locking tab on the clip and pulling the clip out toward you.

CENTER PANEL BRACKET

Push on the locking tab.

CLIP

VEHICLE HARNESS

8. Reach through the glove box area, and loosen the bolt that secures the center panel. Reach through the area near the steering wheel, and loosen the bolt that secures the center panel. Remove the center panel (eight clips, and unplug the connectors).

BOLTS (Loosen from the inside.)

9. Remove the dashboard center low er cover , and disconnect the accessory power socket connector. Remove the two self-tapping screws from the back of the front center console.

SELF-TAPPING SCREW

DASHBOARD CENTER LOWER COVER

FRONT CENTER CONSOLE

10. Slide the front seat completely forward. Remove the rear center console (two washer-screws, two clips, and two retaining tabs). Take care not to damage the clips and retaining tabs.

CENTER PANEL

CLIPS (8)

ANTENNA LEAD

VEHICLE CONNECTOR

WASHERSCREW

REAR CENTER CONSOLE

RETAINING TABS (2)

HOOK

CLIPS (2)

RETAINING TAB

11. Remove the front center console:

• Slide the front seat completely rearward.

13. Turn over the cargo area mat, and remove the cargo area floor.

• Open the lid, and take out the console box mat.

• Remove the two bolts from the inside of the pocket.

• Remove the two clips, then slide the front center console to the rear to release the four retaining tabs. Take care not to damage the retaining tabs.

CONSOLE BOX MAT

CLIP

RETAINING

BOLT

TAB

CLIP

CARGO AREA MAT

CARGO AREA FLOOR

14. Remove the cargo area mat (three clips).

CLIPS (3)

BOL T

Open the lid. FRONT CENTER CONSOLE

12. Open the hatch, and remove the center shelf.

CENTER SHELF

CLIP

CARGO AREA MAT

+ 9 hidden pages