High Speed Blender
Instruction Manual
Model: NY-8608
AC120V, 50/60Hz, 1450W
[ IMPORTANT ]
Important Safeguards
2
Parts and Features
5
Control Panel
6
Operational Area Features
7
Variable Speed Dial (Manual) Features
9
Operating Instructions
12
Using Variable Speed Dial
13
FAQ
13
Cleaning & Maintenance
14
Troubleshooting
15
Warranty & Service
16
Please feel free to check out our
website www.homgeek.com
for more information.
Most customer has useful discover there,
you probably will, too.
[ CONTENT ]
- 01 -
IMPORTANT SAFEGUARDS
1. Read all instructions.
2. Carefully observe and follow all warnings and instructions.
3. Take your time and exercise care during unpacking and appliance setup. This appliance contains
4. Take inventory of all contents to ensure that you have all parts needed to properly and safely
5. This appliance is not intended for use by persons (including children) with reduced physical, sensory,
6. Do not allow children to operate this appliance or use as a toy. Close supervision is necessary when
7. To protect against the risk of electric shock, DO NOT submerge the appliance or allow the power
8. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or
9. To avoid a hazard due to inadvertent resetting of the thermal cut-out, power to this blender must not
10. Do not operate any blender with a damaged cord or plug or after the blender malfunctions, or is
11. GFI circuit breakers might be installed in your kitchen. Look for them in outlets near sinks. If the
12. This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric shock,
13. This appliance has important information on the plug prong. The power cord is not suitable for
14. Before use, wash all parts that may come into contact with food. Follow washing instructions covered
15. ALWAYS use the appliance on a dry and level and firm surface. Never operate the appliance on
- 02 -
WARNING: This unit contains electrical connections and moving parts that potentially present risk to
the user. To avoid the risk of serious injury when using your blender. basic safety precautions should be
followed, including but not limited to following:
READ ALL INSTRUCTIONS, SAFEGUARDS, AND WARNINGS BEFORE OPERATING BLENDER.
The failure to follow any of the important safeguards and instructions for safe use is a misuse of your
blender, which can create the risk of serious injure and void your warranty.
sharp blades that can cause injury if mishandled.
operate your appliance.
or mental capabilities, or lack of experience and knowledge, unless they are closed supervised and
instructed concerning use of the appliance by a person responsible for their safety. Close supervision is
necessary when any appliance is used by or near children. Children should be supervised to ensure that
they do not play with the appliance.
any appliance is used near children.
cord to contact any form of liquid.
disassem-bling parts and before cleaning. To unplug, grasp the plug and pull from the out let. Never pull
from the power cord.
be supplied through an external switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
dropped or damaged in any manner. Email support@homgeek.com at once for information on examination, repair, or adjustment.
blender won’t operate, unplug the blender. Reset the wall outlet or circuit breaker. If the circuit breaker
continues to trip, unplug the blender from the outlet. Allow the blender to sit for 24 hours before attempting
to use it again. Contact Customer Service if the problem persists.
this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. DO NOT modify the plug in any way.
replacement. If damaged, contact homgeek for servicing in order to avoid a hazard.
in this instruction manual.
soft surfaces.
16. Avoid touching moving parts.
17. Alteration or modification of any part of the blender base or container, including the use of any part
or parts that are not genuine authorized homgeek parts, may cause fire, electric shock, or injury.
18. The use of attachments, including canning jars, not expressly authorized or sold by homgeek for
19. Do not use outdoors.
20. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use blender for other
21. Check if the voltage you are using matches the voltage listed on the machine.
22. Do not let cord hang over edge of table or counter.
23. Do not let cord come into contact with hot surface, including the stove.
24. DO NOT operate this appliance on or near any hot surfaces (such as gas or electric burner or in a
25. Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons or
26. The tamper provided must be used only when the main part of the lid is in place.
27. Do not leave foreign objects, such as spoons, forks, knives or the lid plug, in the container as this will
28. Never attempt to operate with damaged blades.
29. DO NOT use the appliance if blade assembly is bent or damaged.
30. Before each use, inspect blades for damage. If blades are bent or damage is suspected, contact
31. Always operate blender with lid and lid plug firmly in place. The lid plug should be removed only when
32. If you find unmixed ingredients sticking to the sides of the container, stop the appliance, remove
33. DO NOT attempt to remove the container and lids from the motor base while the blades are still
34. Add ingredients to the container. NOTE: Do not overfill! To avoid spilling, do not add ingredients
35. When blending hot liquids or ingredients, use caution; spray or escaping steam may cause scalding
36. When making nut butters or oil-based foods, do not process for more than one minute after the mixture
37. Machines and power cords should be stored in a safe place to prevent children from pulling on the
38. Blades are sharp-handle with care. Clean around the blades in the container with extreme care to
39. Never attempt to operate with the centering pad removed.
40. Make sure that the container and blades base are flush with the centering pad to ensure that the
41. DO NOT attempt to Defeat the interlock mechanism.
42. DO NOT use your container to heat ingredients.
43. DO NOT continuously use your machine for more than 5 minutes.
- 03 -
use with this blender, including container, may cause fire, electric shock, or injury.
than intended use.
heated oven). Never leave an appliance unattended when in use.
damage to the blender. A scraper may be used but must be used only when the blender is not running.
damage the blades and other components when starting the machine and may cause injury.
homgeek to arrange for replacement.
adding ingredients and when using the tamper.
the lid, and use a spatula to dislodge ingredients. NEVER insert your hands into the container, as you
may contact one of the blades and experience a laceration.
spinning. Allow the appliance to come to a complete stop before removing lids and containers.
past the “MAX” fill line.
and burns. Do not fill container over half full of the capacity. Always begin processing on the lowest
speed setting, variable speed 0 and slowly increase speed. Keep hands and other exposed skin away
from the lid opening to prevent possible burns.
starts to circulate in the container. Processing for longer periods can cause dangerous overheating.
power cord.
avoid injury.
drive spline is engaged with the drive socket before operating.
44. DO NOT attempt to sharpen blades.
45. DO NOT expose container to extreme temperature changes.
46. Appliance accessories are not intended to be used in the microwave. Do not place the container or the
lid in the microwave as it may result in damage to the accessories.
47. Extension cords are not recommended for use with this product.
48. If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset,
49. DO NOT store ingredients before or after blending them in the container with the blades attached.
50. Never handle the plug with wet hands.
51. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any
52. Flashing light indicates ready to operate. Avoid any contact with blades or moveable parts.
53. Save this manual for future reference.
Before using the product,
The voltage to use should be
please read the manual and all
220V-240V.
explanations carefully.
Please don’t use the product
Please don’t let children use
beyond its functions.
the product.
Please stop using the product
Please don’t let power line touch
when power line or plug damage
sharp edge or high temperature
or other functions failure.
surface.
The product must be operated
Hold the plug tightly when pulling
on stable reliable worktable.
it, don’t pull its line.
The product is household use
Don’t put the product into water
only.
or any other liquids
unplug the appliance and allow it to cool for approximately 1 hour before using again.
Some foods may contain active ingredients or release gases that will expand if left in a sealed container,
resulting in excessive pressure buildup that can pose a risk of injury.
control to “off”, then remove plug from wall outlet.
SAVE THESE INSTRUCTIONS
Household use only
WARNING
To ensure safety, please don’t disassemble the product privately. If there is abnormal
situation, please contact customer service which contact information is printed on the
manual. It must be repaired by manufacturer or special technician of after-sale
service center appointed by manufacturer.
- 04 -
Product
Voltage
Frequency
Power
Capacity
Max. Speed
Model
NY-8608
120V
60Hz
1450W
2.0L
33000RPM
Lid Plug
2.0L Container
Tamper
Blades
Centering Pad
Control Panel
Motor Base
Slip Resistant
Feet
Slip Resistant
Feet
Power Cord
2-Part Lid
Specifications
PARTS & FEATURES
- 05 -
2-Part Lid:The 2-part Lid is easy to put on and take off and easy to clean.
bca
b. On/off key
Controls power to the machine
a. High/Variable Switch
High: The highest speed available
Variable: Activates the Variable Speed Dial
c. Variable Speed Dial
Manual control of lower speed from Variable 0 (stop) to 10
e. LCD Display Screen
Displays speed in orange number and time in white number
fef. Indicator light
d
Always use the complete 2-part lid when blending, especially when blending hot ingredients (unless
the tamper is inserted through the lid plug opening). Never operate the blender without the lid securely
latched during operation.
Lid Plug: Insert through the lid plug opening and secure by turning clockwise. Turn counterclockwise and
lift it to remove the lid plug for using the tamper or adding ingredients.
Container: Ounces/milliliters/cups are clearly marked.
Blades: Blades are made of ultra-sharp stainless steel. The container is designed to be completely
cleanable without removing retainer nut and blades. DO NOT attempt to remove the retainer nut or blades
from the container.
Centering Pad: The container must be aligned over the centering pad. Never attempt to operate with the
centering pad removed.
Motor Base: The motor is designed with dual protection circuits to prevent overheating and an overload.
Tamper: Used to process thicker mixtures and keep ingredients moving towards and through the blades.
CAUTION 1: The tamper can only be used only when the main part of the lid is in place. Hold
the container while using the tamper.
CAUTION 2: Lids and tampers are not interchangeable between different container styles, types, and sizes.
Power Cord: The blender is equipped with a long power cord. Store the unused portion neatly underneath.
Bottom View/Cord Wrap: Plastic cord retainers hold the cord securely. They are flexible and return
to position after the cord is lifted out.
Slip Resistant Feet: Prevent movement during use and prevent damaging marks on countertops or tables.
CONTROL PANEL
- 06 -
a. On/Off key: This key controls power to the machine. Push up to turn on the machine. Push down to
turn off.
b. High/Variable Switch:
Program
Speed
Working
Is Time
Time Range
Auto
Used for
Time
Adjustable?
start after
Making
Time elapses
whole-food
juices soups,
DIAL
0-10
Elapsed time
when using
0 second
0 seconds
shakes, frozen
Variable Speed
mixtures,
Dial
purees, nut
butters, and for
grinding grains.
High: The High function can be used when a smart program is selected and when you are using
Variable Speed Dial. Pushing the High/Variable Switch up to High position will cause the machine to
blend at the highest speed available. High provides the best quality of refinement, breaking down ice,
frozen fruit, whole fruits or vegetables, and grains to a smooth- lump-free consistency.
WARNING: Do not begin processing directly on the High setting.
Always make sure that the High/Variable Switch is set to Variable before pushing the On/Off Switch
to the On position.
Variable: Switch to Variable to activate all of the lower variable speeds by using Variable Speed Dial.
c. Variable Speed Dial: Gives you manual control of lower speed from Variable 0 (stop) to 8. It is
active only when the High/Variable Switch is set in the Variable position. LCD Display Screen displays
speed number in orange color when turning Dial. Timer will count up and elapsed time in white color will
be displayed on LCD screen.
Warning: Always make sure that the marker on Variable Speed Dial is set to 0 before pushing the
On/Off Switch to the On position.
OPERATIONAL AREAS FEATURES
Variable Speed Dial (manual) Features
- 07 -
4 Preset Smart Programs’ Feature
Program
Speed
Preset
Is Time
Time Range
Auto
Used for
Working Time
Adjustable?
start after
Make silky
smoothies,
Program
shakes and
SMOOTHIE
55seconds
No
Program
0 seconds
other drinkable
controlled
beverages from
controlled
fresh or frozen
fruit, milk,
liquids, and ice.
Turn ice, frozen
FROZEN
Program
50seconds
No
Program
0 seconds
juices and fruit
into icy, cold
DESSERT
controlled
controlled
drinks and
desserts.
ICE CRUSH
Program
1 minute and
Program
Crush hard ice
controlled
No
0 seconds
into sorbet in a
20 seconds
controlled
flash.
Program
Program
Blend soup
SOUP
5 minutes
No
0 seconds
from hot
controlled
controlled
ingredients.
1. Remove all packaging materials and labels from the appliance.
2. Container, lids, and tamper are not dishwasher safe. If preferred, wash all parts in warm soapy water.
OPERATING INSTRUCTIONS
IMPORTANT: READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY BEFORE USE. THE
FAILURE TO FOLLOW ANY OF THE IMPORTANT SAFEGUARDS AND IMPORTANT SAFETY
INSTRUCTIONS FOR SAFE USE IS A MISUSE OF YOUR BLENDER THAT CAN VOID YOUR
WARRANTY AND CREATE THE RISK OF SERIOUS INJURY.
BEFORE FIRST USE
WARNING: Blades are sharp. Use extreme caution when handling.
Rinse clean under running water and dry thoroughly. Wipe the motor base with a warm, damp cloth and
wipe clean with a dry, soft cloth. Allow all parts to dry completely before using.
WARNING: Do not place the motor base in water or other liquids. Do not let any liquid enter
the motor.
- 08 -
WARNING
1. Place motor base on a clean, dry, even, level and firm surface such as a countertop or table.
2. Make sure the centering pad is securely aligned over the motor base before using.
Electrical Shock Hazard
Use grounded outlet only.
DO NOT use an adapter.
DO NOT use an extension cord.
DO NOT remove ground.
Always unplug before cleaning or when not in use. Do not put the
motor base in water or any other liquids or let any form of liquid
enter the motor.
Failure to follow instructions in manual can cause death
or electrical shock.
IMPORTANT: This unit contains electrical connections and moving parts that potentially present a risk
to the user. Read all important safeguards and instructions before operating the blender.
USE YOUR BLENDER
Centering Pad
Motor Base
3. Cut food into smaller pieces for more efficient blending. Add ingredients to the container, making
sure not to exceed the “MAX” fill line.
WARNING:
DON’T fill container with Hot ingredients over half full capacity to avoid overflow and cause injury.
NOTE: If you need to add additional ingredients while the appliance is processing, open the lid plug and
pour ingredients in through the lid plug opening. Make sure the main part of the lid is in place when
adding ingredients.
IMPORTANT: NEVER RUN THE APPLIANCE EMPTY.
- 09 -
Tips: How to load your container
according to your recipe?
We suggest, liquids first, then
dry goods, leafy greens, fruit &
veggies and finally ice &
frozen ingredients.
Ice & Frozen Ingredients
Fruit & Veggies
Leafy Greens
Dry Goods
Liquids
4. With the motor off, set the container on the motor base by aligning it over the centering pad. The
container can be installed in four different orientations. The handle can be aligned on either of the 4 sides
of the motor base. Do not ever attempt to put a container on an operating motor base or to operate a
motor base without a container properly in place. The motor will not work if the container is not installed
correctly.
CAUTION: Never attempt to remove the container while the appliance is still running.
5. Push the lid down into container firmly with lid flaps midway between the spout and the handle. Make
sure that both side clips on lid fully snap onto lip of container. Insert the lid plug into the lid plug opening
and turn clockwise to lock in place.
CAUTION: Never operate the blender without the lid securely latched during operation. Always use the
complete 2-part lid when blending, especially when blending hot ingredients (unless the tamper is inserted
through the lid plug opening).
- 10 -
6. Check up the Variable Speed Dial. Make sure the High/Variable Switch is switched to Variable
position and the marker on Variable Speed Dial is pointing to “0” before powering on. When the unit is
connected to power and the container is correctly put onto the motor base, the unit will work at once under
the set speed that the marker on Variable Speed Dial is pointing if the marker on Variable
Speed Dial is not at “0”.
7. Plug the blender into a grounded, 2-prong outlet. On will be displayed on the LCD Display Screen
indicating that the appliance is ready for use. The indicator light of 4 smart programs will be on
indicating that now you can select a smart program or you can also use the Variable Speed Dial.
Warning: Make sure the power plug is safely connected to a grounded wall electrical socket.
Power Supply
120V AC
Warning: After plugged in, NEVER insert your hands into the container, as you may contact one
of the blades and experience a laceration.
8. Start to blend either using, Variable Speed Dial, or simply pressing a smart program button.
IMPORTANT! Never start on speeds above 0 with hot liquids to avoid possible burns. Always
start on Variable 0 and slowly increase speed. Escaping steam, or splashes from contents may
scald. Lock the lid and lid plug securely in place before operating the machine.
- 11 -
USING VARIABLE SPEED DIAL
1. Make sure the marker on Variable Speed dial is at “0” position.
2. Push the On/Off Switch up to On position, then slowly increase to the desired speed between 1 and
3. During blending, you can push the High/Variable Switch up to High position for the highest speed
4. To stop blending, turn the marker on Variable Speed Dial to “0” and blender will enter standby mode.
a. Make sure the High/Variable Switch is at Variable position and the marker on Variable Speed Dial is
b. Simply press one of the 4 programs key. It will automatically start blending under selected program.
c. The High function can be used when a program is selected. Pushing down the High/Variable Switch
d. The program will automatically stop after it’s completed. Alternatively, you can press the currently-
8 during the blending cycle.
of blending and turn it back to Variable position for using Variable Speed Dial again.
Push the On/Off Switch down to Off and blender will power off.
Note:
Make sure that the marker on Variable Speed Dial is pointed to “0” after each use.
USING 4 SMART PROGRAMS
The speed and time for these programs are set by default. These programs have pauses or changes
in speed throughout the cycle.
pointing to “0”. Pushing the On/Off Switch up to On and blender will enter standby mode. On will appear
on the LCD Display Screen.
Number “0” in orange color on LCD Display Screen will be running quickly during blending. Countdown
time number in white color will be displayed on LCD screen.
to High position when a program is selected will cause the machine to run at the highest speed available.
The timer will continue counting down under High mode. Returned to Variable position and blender will
continue to work under the selected program.
run-ning program button again to stop the program and blender will enter standby mode. Or simply turn
the On/Off switch to Off and blender will power off.
Tips:
How to switch among each smart program during blending?
Method:
During blending, simply press another desired program key. The newly-selected program indicator light
will be on, indicating its selection. Blender will be switched to immediately blending under the newly-selected program upon its selection.
How to use smart programs when using Variable Speed Dial?
Method:
Simply press the desired program key directly. The newly-selected program indicator light will be on
and will auto-start blend at once.
How to use Variable Speed Dial when using smart program?
Method:
Simply turn the marker on Variable Speed Dial at least one speed range, it will auto-start blending
under set speed at once.
- 12 -
* If ingredients are not blending properly, use a tamper to help push ingredients towards blades. If this
9. When blending is complete, turn off and unplug the appliance. Wait for the blades to completely stop
10. To remove the container from motor base, lift it off the motor base.
1. Place ice into the container (no more than 1/3 of the way full).
2. Securely lock the lid to the container, and remove the lid plug.
3. Turn on the blender and select "ICE CRUSH" program.
4. Use tamper to push ice down into the blades.
5. The program will stop automatically when finished. You can also manually stop blending before the
6. Unplug and remove the ice by turning the container upside down. Use a plastic spatula and carefully
does not work, press On/Off to Off position to power off. Remove the container from the blender base
and use a rubber spatula to press the air bubble away from the blades. Add liquid if necessary.
Replace the lid and lid plug. Replace container to the motor base and continue blending.
spinning.
CAUTION: Make sure that the motor base is unplugged when not in use.
WARNING: Be sure to wait for the unit to come to a complete stop before removing the container from
the base or the lid from the container.
11. To remove the lid, lift up on one lid flap while holding the container securely. The container can then
be emptied. If hot ingredients were blended, carefully hold the container handle, then place the container
on a flat surface.
CAUTION
Moving Parts May
Become Hot with
Extended Use.
DO NOT touch.
FAQ
1. How to crush ice?
homgeek Blender can crush ice cubes into sorbet.
To achieve the best results, the ice must be dried instead of watery or melting. The container should
be dry. Tamper is also needed.
ice starts melting.
shift ice stuck underneath the blades.
Note:
If dry ice is not available, you can crush 1 ice: 1 water.
2. How to determine the tamper is suitable for your blender?
Remove the lid plug and insert the tamper through the lid plug opening. The tamper should fit easily into
the opening. It should not come into contact with the blades no matter where you move the tamper inside
the container.
- 13 -
WARNING：
* DON’T submerge the motor base into water or any other liquids.
(1) Fill the container half full with warm water and add a couple of drops of dishwashing liquid.
(2) Make sure the 2-Part lid is securely snapped onto container.
(3) Perform one of the following procedures:
a. Make sure the marker on Variable Speed Dial is at 0. High/Variable Switch is at Variable position. Push
- 14 -
IF THE TAMPER TOUCHES THE BLADES AT ANY ANGLE, DO NOT USE THE TAMPER WITH YOUR
CONTAINER.
3. How to use the tamper?
IMPORTANT! The splash disk (near the top of the tamper) and
lid prevent the tamper from hitting the blades when the lid is
secured properly in the locked position.
a. The container should not be more than two-thirds full when the
tamper is used.
b. If the food does not circulate, the blender may have trapped an
air bubble. While ensuring that the lid remains firmly in place,
carefully remove the lid plug.
c. Release the air bubble by inserting the tamper through the
lid plug opening.
d. Holding the tamper straight down may not help the ingredients
circulate. Point the tamper towards the sides or corners of the
container if necessary. DO NOT try to force the tamper deeper
into the container.
CAUTION:
The tamper can only be used when the main part of the lid is in
place. Hold the container while using the tamper. To avoid
overheating during blending, DO NOT use the tamper for more
than 30 consecutive seconds.
CLEANING AND MAINTENANCE
CAUTION：
*To avoid inadvertent activation, unplug from outlet before assembling or disassembling parts, and
before cleaning.
DON’T let any liquid enter the motor.
Please refer to all instructions included in this book.
IMPORTANT: To ensure continued and effective performance, do not put the container, lid, or lid plug
in the dishwasher. Clean the appliance after every use.
1.To clean container, lid, lid plug, tamper and centering pad:
Self-Cleaning:
(without removing the container, lid and lid plug):
：
the On/Off Switch up to On position.
b. Slowly increase the variable speed to Variable 8.
c. Run the machine for 30 to 60 seconds. For best results, using short “High” several times.
d. Rotate the Variable Speed dial back to Variable 0 and turn off the machine.
e. Rinse clean under running water and dry thoroughly.
1. Unplug the appliance.
2. Make sure all parts are clean & dry and placed in a clean and dry place.
3. Store the blender upright with the lid secured on top.
4. Store the unused portion of the power cord neatly underneath as picture.
Hand Wash:
(remove the container, lid, and lid plug)
a. Wash the container, lid, and blades in warm soapy water. Rinse clean under running water and
dry thoroughly. Centering pad can be removed for more thorough cleaning.
CAUTION:
blades with care to avoid laceration caused by contact with sharp edges.
2. To clean motor base:
Clean the motor base with a soft, damp cloth to prevent scratching.
Do not submerge the motor base into water and or other liquids. Do not let any liquid enter the motor
HOW TO STORE?
Any other servicing should be performed by an authorized service representative.
- 15 -
TROUBLESHOOTING
1.If the blender does not start, check to make sure you have plugged
the unit in and that the On/Off switch is at On.
2.Make sure the container is securely placed on the motor base.
Motor doesn’t start or
3.Check the fuse or circuit breaker.
blades doesn’t rotate
The blender has dual-protection circuits.
a.For overheating.
b.For overloads.
If the motor overheats, allow it to cool for 1 hour; if overloaded,
unplug and plug again after 3 minutes.
Food is chopped too
The food has been over-processed. Use High mode for controlled
finely or is too watery
processing. Or stop blending if necessary.
Food collects on lid
The mixture is too thick. Add more liquid or use the tamper to help
or on the sides of the
push the ingredients toward the blades. The container should not be
blades
filled more than 2/3 (for the sake of consistency) full when the tamper
is used during blending.
You cannot create
DO NOT use ice that has been sitting out or has started to melt. Use
snow from solid ice.
ice straight from the freezer.
WARNING:
To reduce the risk of shock and unintended operation, turn off power and unplug unit before
troubleshoot-ing.
WARRANTY AND SERVICE
*1-Year Full Machine Warranty
This warranty coverage applies to the owner of this blender for personal household use only and to the
original product only and is not transferable. This Warranty does not apply to products for commercial,
rental or re-sale purposes.
homgeek warranty guarantees owner that if this blender fails within 1 year form the date of purchase due
to defects in materials and workmanship under normal household conditions, homgeek will in homgeek’s
sole discretion, elect to either(A)replace the Blender free of charge or(B) refund the owner, unless
homgeek receives prior written notice of the owner’s preference. In the rare event that a replacement unit
is issued, the warranty coverage ends six months after the receipt date of the replacement unit or the
remainder of the existing warranty, whichever is greater. If the unit id replaced, homgeek reserves the
right to replace the unit with one of equal or greater value.
This warranty is only valid if the blender is used and maintained in accordance with the instructions,
warnings and safeguards contained in the owner’s manual. This warranty only applies to product
- 16 -
purchased through an authorized dealer.
This warranty does not cover damages or wear resulting from accident, misuse, abuse, commercial use,
or unauthorized adjustment and/or repair by homgeek. homgeek shall not be liable for loss of use or any
other incidental, consequential or indirect costs, expenses or damages. There are no express warranties
except as listed under the terms of this Limited Warranty. This warranty gives you specific legal rights,
and you may have other rights which vary from state to state.
If your appliance is found to be defective or fails to operate properly while in use under normal household
conditions within the warranty period, please email us at support@homgeek.com. Please note that proof
of purchase is required.
Shenzhen TOMTOP Technology Co., Ltd.
Add: G-4 Zone 5/F, No.1 Exchange Square, Huanan City, Pinghu Town, Longgang District,
Shenzhen, Guangdong, CN 18111
www.homgeek.com
support@homgeek.com
- 17 -
Loading...