Home Styles 9200-1211 User Manual
88 9200 002C
Kitchen Cart
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
PART LIST
H.
Back Stretcher
1 pc.
J.
Base
1 pc.
P.
Adj. Shelf
2 pcs.
B.
Side Panel
1 pc.
Q.
Adj. Shelf
1 pc.
Stretcher
K.
Door
Front
1 pc.
.2 pcs
C.
Middle Panel
2 pcs.
I.
Side Rack
1 pc.
L.
Door
2 pcs.
R.
M.
Drawer
Divider
1 pc.
D.
Side Panel
1 pc.
E.
Back Panel
2 pcs.
F.
Back Panel
1 pc.
N.
KD. Drawer
2 pcs.
(For Drawer N, packed in separate carton
with hardware and assembly instructions.)
S.
Side Rack
1 pc.
T.
Base Rack
1 pc.
G.
Back Piece
2 pcs.
HARDWARE LIST
Caster
two lock
two non-lock
4 pcs.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Head Cap Bolt (short)
for Side Towel Bar
2 pcs. (+1 extra)
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
Wood Screw
for Caster
16 pcs. (+2 extra)
Head Cap Bolt
11 pcs. (+1extra)
Adjustable Pin
12 pcs. (+2extra)
Head Cap Bolt
(short) for Top
4 pcs. (+1 extra)
servicedesk@homestyles-furniture.com
Wood Plug
8 pcs.
(+2 extra)
Steel Plate
Connector
for Top
4 pcs.
U.
Brush Chrome Pipes
3 pcs.
4 pcs. (+1 extra)
Spring
Washer
for Top
4 pcs. (+1 extra)
Towel Bar
1 pc.
Revised date : 30Oct2012
Flat
Washer
for Top
Machine Screw
for Pull Handle
8 pcs.
O.
Pull Handle
4 pcs.
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to
tighten up the Head Cap Bolts in the future.
STEP 1
Attach four Casters to the Base (J) with
Wood Screws.
(See the ‘Arrow’ sticker indicating front area
on the base.)
STEP 2
Attach the Side Panel (D) to the Base (J).
Assembly Instructions 2/3
G
C
C
G
D
Tighten Head Cap Bolt only half way.
Attach the Back Piece (G) to the Base
and the Middle Panel (C) to the Back Piece (G).
Tighten Head
Cap Bolt by
Hex Wrench.
Head Cap Bolt
STEP 3
Slide the Back Panel (E) and (F) in places.
Attach the Back Stretcher (H) and Front
Stretcher (I) to the unit with Head Cap Bolts
through the Side Panel (D).
Tighten Head Cap Bolts half way.
Locking Casters
E
B
H
J
Head Cap Bolt
Head Cap Bolt
(short)
M
F
I
E
O
Attach the Drawer Divider (M) in between
the Back Stretcher (H) and Front Stretcher
(I), using Head Cap Bolt.
Attach the Side Panel (B) to the unit, using
Head Cap Bolts.
Tighten up all Head Cap Bolts.
Attach the Towel Bar (O) to the Side Panel (D), using Head Cap Bolts (short).
D
Head Cap Bolt
Loading...