88 9001 001 C
Kitchen Cart (Natural)
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
PART LIST
Casual Attire For Today's Home
Thai Patent Numbers 15272
A.
Side Panel
1 pc.
F.
Back
Stretcher
1 pc.
G.
Front Rail
1 pc.
L.
Side Towel Bar
1 pc.
M.
Shelf
1 pc.
HARDWARE LIST
B.
Side Panel
1 pc.
Side Rack
N.
Door.
1 pc.
H.
1 pc.
C.
Base
1 pc.
I.
Side Rack
1 pc.
O.
Door.
1 pc.
D.
Back Piece
1 pc.
J.
Brush Chrome Pipes
3 pcs.
E.
Back Panel
2 pcs.
P.
Drawer
1 pc.
K.
Base Rack
1 pc.
Hex Wrench
1 pc.
Caster
two lock
two non-lock
4 pcs.
Tools Required For Assembly : Philips screwdriver
Head Cap Bolt (short)
for Side Towel Bar
2 pcs.
(+ 1 extra)
Head Cap Bolt (Middle)
for top
4 pcs.(+ 1 extra)
Head Cap Bolt
(long)
12 pcs.(+ 1 extra)
Machine Screw
for Pull Handle
4 pcs.
Pull Handle
2 pcs.
Adjustable Pin
4 pcs. (+ 1 extra)
Wood Screw
16 pcs.
(+ 1 extra)
Wood Plug
8 pcs.
(+2 Extra)
Assembly Instructions 2/4
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to
tighten up the Head Cap Bolts in the future.
STEP 1
Attach four Casters to
the underneath of the Base (C).
Locking Caster
D
Wood Screw
C
Locking Caster
STEP 2
Attach the Side Panel (B) to the
Base (C).
C
Tighten up the Head Cap Bolts.
Attach the Back Piece (D) on the Base rear.
B
Tighten Head
Cap Bolt by
Hex Wrench.
Head Cap Bolt
F
Assembly
Head Cap Bolt
Instructions 3/4
Head Cap Bolt
J
A
A
E
G
Head Cap Bolt
E
STEP 3
Slide the Back Panel (E) in place.
Attach the Back Stretcher (F) on the unit
B
with the Head Cap Bolt.
Attach the Front Rail (G) to the
Side Panel (B) with Head Cap Bolt.
Attach the Side Panel (A) to the unit with
Head Cap Bolts.
STEP 4
Attach the Side Rack (H) to the Side Panel (A)
with the Head Cap Bolts.
H
K
J
I
STEP 5
Attach the Side Towel Bar (L)
to the Side Panel (B) with
Head Cap Bolts.
Attach the Brush Chrome Pipes (J) to the pre-drilled
holes of Side Rack (H).
Attach the Base Rack (K) to the Side Rack (H).
Attach the Side Rack (I) to the Side Panel (A),
using Head Cap Bolts.
Head Cap Bolt
(for Side Towel Bar)
B
B
L
Assembly
STEP 6
Now, you’ll be able to create your own kitchen cart.
Make your own choice of the ‘Top’, wood or stainless
steel or granite.
Place the Top on the unit, then tighten
the Head Cap Bolts.
Insert the Adjustable Pins into both side
panels at the desired level.
Place Shelf (M) into place.
Head Cap Bolt
(for Top)
Adjustable pin
Instructions 4/4
Head Cap Bolt
(for Top)
N
P
O
M
STEP 7
Attach the Pull Handles to the
Door (N) and (O) using the
Machine Screws. (See figure 1)
Attach the Door (N) and (O) to both
side panels, slide the door lift hinges
into the side frame lift hinges.
(See figure 2)
Slide the Drawer (P) into place.
(Drawer is packed in separated
carton).
Figure 1
Figure 2
STEP 8
Cover up all holes
with Wood Plugs
88 9001 001 C
Drawer (P)
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.
Unit Part List
P1.
Front Part
1 pc.
P2.
Back Part
1 pc.
P3
(Fig)1
P2
P3.
Side Part
1 pc.
P1
P4
HARDWARE LIST
P4.
Side Part
1 pc.
Pull Handle
1 pc.
P5.
Base
1 pc.
Assembly
Machine Screw
for Pull Handle
2 pc.
Instructions
(Fig) 1
Assemble the Front Part (P1), Back Part
(P2) and Side Part (P3) and (P4).
Using a Phillips screw driver, insert 1”
screw into the pre-drilled holes at the
side parts, tighten half way.
Wood Screw
(for Base)
6 pcs.(+1 extra)
Wood Screw
(for Side Part)
8 pcs.(+1 extra)
(Fig) 2
Slide the Plywood Base (P5) into the grooves
on side parts. Be sure to push the Base all the
way forward so it meets the Front Part.
P3
P1
P5
P4
P2
(Fig)3
(Fig) 3
Insert the remaining ½” screws (6 pcs.)
into the pre-drilled holes at the Base,
then tighten up all screws.
(Fig) 4
Assemble the Pull Handle
to the Front Part with
Machine Screw.
P3
P5
(Fig)2
P1
P4
(Fig)4
Loading...