Page 1
88 5516 991
Barnside Bar
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
A.
Top
1 pc.
E.
Door
1 pc.
Hardware List
M6x30
Head Cap Bolt
Hex Wrench
1 pc.
8 pcs. (+1 extra)
F.
Foot Rest
1 pc.
G.
Foot Rest Support
2 pcs.
Cam Lock Screw
19 pcs. (+2 extra)
M4x16
Wood Screw (short)
8 pcs. (+1 extra)
H.
Middle Shelf
1 pc.
Magnet
1 pc.
B.
Middle Panel
1 pc.
M4x25
Machine Screw
3 pcs.
C.
Shelf
1 pc.
l
D.
Shelf
2 pcs.
Knob
1 pc.
Small
Hex Wrench
1 pc.
Cam Lock
19 pcs. (+4 extra)
M4x25
Wood Screw (long)
for drawer side
8 pcs. (+1 extra)
Adjustable Pin
12 pcs. (+1 extra)
Pull Handle
1 pc.
For assembly also need the following : 88 5516 992
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Leve
Home Styles Consumer Assistance: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
l
Page 2
88 5516 992
Barnside Bar
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
N.
Bottom
1 pc.
I.
Side Panel
1 pc.
P.
Back Rail
1 pc.
K.
Front Panel
1 pc.
J.
Side Panel
1 pc.
L.
Front Panel
1 pc.
O.
Front Rail
1 pc.
Q.
Drawer
1 pc.
(Please refer to the last page of these
instructions for drawer assembly step.)
For assembly also need the following : 88 5516-991
M.
Front Panel
1 pc.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
Page 3
Assembly Instruction 2 / 5
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the fl oor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
B
A
Cam Lock Screw
J
I
H
Cam Lock Screw
N
STEP 1
Insert Cam Lock Screws into the pre-drilled holes of Top (A), Middle Panel
(B), Side Panel (I), (J), Middle Shelf (H) and Bottom (N). (see Figure 1)
Figure 1
Page 4
O
Assembly Instruction 3 / 5
STEP 2
Attach Front Panels (K) and (M) to
Front Panel (L).
K
Attach Front Rail (O) to panel unit.
L
M
STEP 3
Attach Middle Shelf (H) to panel
unit.
Attach Middle Panel (B) to Middle
Shelf (H) with Cam Locks.
(see Figure 2)
Attach Back Rail (P) to Middle
Panel (B) using Cam Lock.
Attach Bottom (N) to unit with
Cam Locks.
P
H
Cam Lock
B
N
Cam Lock
J
I
Figure 2
Figure 3
Head Cap Bolt
STEP 4
Attach Side Panels (I), (J) to unit from Step 3 with
Cam Locks and Head Cap Bolts. (see Figure 3)
Page 5
Assembly Instruction 4 / 5
Head Cap Bolt
STEP 6
G
F
G
Figure 4
STEP 5
Attach Foot Rests Supports (G) to unit
with Head Cap Bolts.
Attach Foot Rest (F) unit with Head
Cap Bolts.
Figure 5
Place Top (A) unit onto the unit
and attach with Cam Locks.
Attach Magnet to middle
panel with Wood Screws
(short). (see Figure 4)
Slide Drawer (Q) into position.
Insert Adjustable Pins into side
panels at the desired level.
Place Shelves (C) and (D) into
position.
Attach Door (E) to side panels by
sliding the door lift hinges
into the side panel lift hinges.
(see Figure 5)
Assemble Knob to Door
(E) with Machine Screw.
(see Figure 6)
Figure 6
Cam Lock
Magnet
Wood Screw (short)
E
Q
Figure 7
A
To level the unit, adjust the
adjustable levelers on the bottom
of unit. (see Figure 7)
Note: Unit must be level to
work properly.
D
Adjustable Pin
C
C
Page 6
Drawer (Q)
Assembly Instruction 5 / 5
Q3
Figure 1
Q2
STEP 1
Attach Q1 to Q2 and Q4, using
a Phillips screwdriver and
long wood screws (4X), tighten
halfway.
Attach Q2 to Q3 and Q4 using
long wood screws (4X), tighten
halfway. (see Figure 1)
Q1Q3
Q1
MAKE SURE ROLLER
IS ON THE BACK
Q4
Figure 2
Q3
Q5
Q1
Q4
STEP 2
Slide Q5 into the grooves in Q3
and Q4. Be sure to push Q5 all
the way forward so it meets
Q1. (see Figure 2)
Q5
Q2
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in Q5
and tighten. (see Figure 3)
Part List
Q1.
Front Part
1 pc.
Q2.
Back Part
1 pc.
Q4
Figure 4Figure 3
STEP 4
Assemble Pull Handle
with machine screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
Q3.
Side Part
1 pc.
Q4
Side Part
1 pc.
Q5.
Base Part
1 pc.
Page 7
Loading...